Mitsubishi Electric CMB-WP-V-GA1 Data Book page 131

1. SPECIFICATIONS
Model
Power source
Cooling capacity
(Nominal)
Power input
Current input
EER
Temp. range of Indoor
cooling Circulating water
Heating capacity
(Nominal)
Power input
Current input
COP
Temp. range of Indoor
heating Circulating water
Indoor unit Total capacity
connectable Model/Quantity
Sound pressure level (measured in anechoic room) dB <A>
Sound power level (measured in anechoic room)
Refrigerant High pressure
piping diameter Low pressure
Circulating water Water flow rate
Pressure drop
Operating volume
range
Compressor Type
Manufacture
Starting method
Motor output
Case heater
Lubricant
External finish
External dimension H x W x D
Protection devices High pressure protection
Inverter circuit (COMP.)
Compressor
Refrigerant Type x original charge
Control
Net weight
Heat exchanger
Water volume in plate
Water pressure Max.
HIC circuit (HIC: Heat Inter-Changer)
Drawing External
Wiring
Standard attachment Document
Accessory
Optional parts
Remarks
Notes:
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Water temperature: 30°C (86°F)
Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.), Water temperature: 20°C (68°FD.B.)
Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
MEE15K052
PQRY-P500YLM-A
3-phase 4-wire 380-400-415 V 50/60 Hz
*1 kW
kcal/h
*1 BTU/h
kW
A 24.6-23.3-22.5
kW/kW
W.B. 15.0~24.0°C (59~75°F)
°C 10.0~45.0°C (50~113°F)
*2 kW
kcal/h
*2 BTU/h
kW
A 22.0-20.9-20.2
kW/kW
D.B. 15.0~27.0°C (59~81°F)
°C 10.0~45.0°C (50~113°F)
50~150% of heat source unit capacity
WP15~WP50/5~50
dB <A>
mm (in.) 22.2 (7/8) Brazed
mm (in.) 28.58 (1-1/8) Brazed
3
m /h
L/min
cfm
kPa
3
m /h
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
kW
kW
Galvanized steel sheets
mm 1,450 x 880 x 550
in. 57-1/8 x 34-11/16 x 21-11/16
High pressure sensor, High pressure switch at 4.15 MPa (601
Over-heat protection, Over-current protection
Over-heat protection
R410A x 6.0 kg (14 lbs)
HBC controller
kg (lbs)
I
MPa
WKS94C744
WKE94G131
Installation Manual
Refrigerant conn. pipe
Main HBC controller: CMB-WP108, 1016V-GA1
Sub HBC controller: CMB-WP108, 1016V-GB1
Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
The ambient temperature of the heat source unit needs to be kept below 40°C D.B.
The ambient relative humidity of the heat source unit needs to be kept below 80%.
The heat source unit should not be installed at outdoor.
Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
Be sure to provide interlocking for the unit operation and water circuit.
Install the supplied insulation material to the unused drain-socket.
When installing insulation material around both water and refrigerant piping, follow the installation manual.
56.0
48,200
191,100
14.58
3.84
63.0
54,200
215,000
13.07
4.82
54
70.5
7.20
120
4.2
44
4.5 ~ 11.6
Inverter
13.0
-
MEL32
psi)
216 (477)
plate type
5.0
2.0
-
Unit converter
BTU/h =kW x 3,412
3
cfm =m /min x 35.31
lbs =kg/0.4536
*Above specification data is
subject to rounding variation.
2 - 42