1. Manuals
  2. Brands
  3. Sensaphone Manuals
  4. Telephone
  5. 1108
  6. User manual

Sensaphone 1108 User Manual

Sensaphone telephone
Hide thumbs Also See for 1108:
Table of Contents

Advertisement

Quick Links

SENSAPHONE
®
Model 110 8
User's Manual
including CottageSitter, BusinessSitter,
RemoteControl & 1118 Line Seizure editions
Version 1.43
PHONETICS, INC.

Advertisement

Table of Contents
loading

Related Manuals for Sensaphone 1108

Summary of Contents for Sensaphone 1108

  • Page 1 SENSAPHONE ® Model 110 8 User’s Manual including CottageSitter, BusinessSitter, RemoteControl & 1118 Line Seizure editions Version 1.43 PHONETICS, INC.
  • Page 2 PHONETICS, INC. assumes no responsibility for the results of errors beyond its control. PHONETICS, INC. also cannot guarantee that changes in equipment made by other manufacturers, and referred to in this manual, will not affect the applicability of the information in this manual.

  • Page 3: Important Safety Instructions

    Do not place on or near a heat source, such as a radiator or heat register. • Do not use your Model 1108 near water, or spill liquid of any kind into it.
  • Page 4 There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. To Reduce the Risk of Fire or Injury to Persons, Read and Follow these Instructions: 1.

  • Page 5: Fcc Requirements

    Connection to party lines is subject to state tariffs. Should the Model 1108 cause harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance. But if advance notice isn’t practical, the telephone company may temporarily...
  • Page 6 Sensaphone ® Model 1108 User’s Manual Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits a designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 7: Canadian Department Of Communications Statement

    Load Numbers of all the devices does not exceed 100. For the Sensaphone® Model 1108, the Load Number is 8.
  • Page 8 Sensaphone ® Model 1108 User’s Manual viii...

  • Page 9: Year Limited Warranty

    1 YEAR LIMITED WARRANTY PLEASE READ THIS WARRANTY CAREFULLY BEFORE USING THE PRODUCT. THIS LIMITED WARRANTY CONTAINS SENSAPHONE’S STANDARD TERMS AND CONDITIONS. WHERE PERMITTED BY THE APPLIC- ABLE LAW, BY KEEPING YOUR SENSAPHONE PRODUCT BEYOND THIRTY (30) DAYS AFTER THE DATE OF DELIVERY, YOU FULLY ACCEPT THE TERMS AND CONDITIONS SET FORTH IN THIS LIM- ITED WARRANTY.
  • Page 10 Sensaphone ® Model 1108 User’s Manual repairs; (6) used in a manner or purpose for which the product was not intended; or (7) sold by original purchaser. LIMITED WARRANTY, LIMITATION OF DAMAGES AND DISCLAIMER OF LIABILITY FOR DAMAGES: THE WARRANTOR’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPAIR OR REPLACE- MENT OF THE PRODUCT, AT THE WARRANTOR’S OPTION AS TO...
  • Page 11 DAMAGES OR COSTS, INCLUDING BUT NOT LIMITED TO DAM- AGES THAT ARE DIRECT OR INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL, AND INCLUDING ATTORNEYS FEES AND LEGAL COSTS, THAT MAY RESULT FROM THE INSTALLATION, OPERATION, USE OF, OR INABILITY TO USE WARRANTORS’ PRODUCTS AND SERVICES, OR FROM THE FAILURE OF THE WARRANTORS’...
  • Page 12 Sensaphone ® Model 1108 User’s Manual The agreement between the Warrantors and the Purchaser, including but not limited to the terms and conditions herein shall not be governed by the Convention for the International Sale of Goods. Where applica- ble, the Uniform Commercial Code as adopted by the State of Delaware shall apply.

  • Page 13: Table Of Contents

    Power Supply and Battery Backup ..22 Starting the Model 1108 ....22 Run Mode and Standby Mode ... . 23 Telephone Line .
  • Page 14 4.2.2 Interrogating a Dial-out Telephone Number ..42 4.2.3 Erasing a Telephone Number....42 Tone or Pulse Dialing ....43 Special Dialing .
  • Page 15 4.12 Maximum Number of Calls (Max Calls) ..61 4.12.1 Programming Max Calls ....61 4.12.2 Interrogating Max Calls ....62 4.13 The Clock .
  • Page 16 Example: A Dial-out Telephone Call ..98 Chapter 8: Model 1108 Special Editions . . . 99 Sensaphone 1108 CottageSitter ..99 8.1.1 Switching the Output using the Keypad ..100 8.1.2 Switching the Output over the Telephone .
  • Page 17 Sensaphone 1108 RemoteControl..108 8.3.1 Switching the Output using the Keypad ..108 8.3.2 Switching the Output over the Telephone ..109 8.3.3 Controlling Lights or other devices... 110 8.3.4 Relay Output Specifications .
  • Page 18 xviii...

  • Page 19: Chapter 1: Introduction

    Designed for desktop or wall mounting, the Model 1108 is simple to install, program and operate; no changes to standard electrical or telephone service are required. Connected to a telephone line, it will respond to an alarm by dialing up to eight separate telephone numbers.

  • Page 20: Technical Support

    (not included) will continue to power the unit for approximately 24 hours. This manual comprises the instructions and commands for installing and operating the Model 1108. The Quick Start chapter is included to speed understanding of programming and operation. Communication and Alarm Programming chapters demonstrate step-by-step methods for utilizing the full range of available features.

  • Page 21: Chapter 2: Installation

    Do not expose to humid environments, fumes, or corrosive vapors. 2.2 Mounting Flat Mount: Place the Model 1108 on top of a desk or other horizontal surface. Wall Mount: Mount on a wall with two screws using the keyholes on the back panel of the unit.

  • Page 22: Power Surge Protection

    ® Model 1108 User’s Manual 2.3 Power Surge Protection The Model 1108 can be damaged by power surges and lightning through the telephone line and the 120 VAC power supply. Although the Model 1108 has built-in surge protection, we recommend that additional protection be obtained for the unit and for any electronic equipment that is attached to your power supply and telephone lines.

  • Page 23: Run Mode And Standby Mode

    LED goes out, but will blink every few seconds to indicate that power is still supplied to the unit. In RUN mode, the Model 1108 is able to receive incoming calls and to automatically dial out in the event of an alarm on one of the monitored conditions.

  • Page 24: The Microphone

    2-4. Figure 2-4. Installing the Telephone Line On the back of the Model 1108 is a female telephone jack. This is provided so that a telephone or other answering device may be used on the same line as the unit. It is not necessary to hook up a telephone for the Model 1108 to operate.

  • Page 25: Alert Inputs

    If this sound level exists for 8 consecutive seconds (default) or for the programmed length of time, the Model 1108 will dial out with an alarm message. The proximity of the audible alarm to the microphone is extremely important.

  • Page 26: Installing The Sensor

    Fasten one lead to the numbered screw and the other lead to GND. Tighten both screws. If the input was not disabled, the Model 1108 may recite its “Alert Condition Exists” message as you connect the sensor. If it does, just press any key to stop.

  • Page 27: Multiple Sensors

    Continue connecting sensors end-to-end until you have connected all of your sensors. Take the second lead from the last sensor and connect it to the ground screw on the Model 1108. See Figure 2-8. Multiple N.C. sensors are typically magnetic reed switches to monitor the security of windows and doors.

  • Page 28: Outdoor Wiring

    2.12 Outdoor Wiring When wiring sensors outdoors, DO NOT allow exposed wires to run freely in open air; under such conditions, the Model 1108 is susceptible to serious damage during a lightning storm. Depending upon the distance outdoor wiring must travel, consideration should be given to use of shielded wire inside a metal conduit.

  • Page 29: Disconnecting The Model 1108 For Storage Or

    Disconnecting the Model 1108 for Storage or Seasonal Use. If you plan to employ the Model 1108 as a seasonal “watchdog” for a few months during the year, you must disconnect all wires from the unit completely to avoid damage to the circuitry when the unit is not in use.
  • Page 30 Sensaphone ® Model 1108 User’s Manual...

  • Page 31: Chapter 3: Quick Start

    Chapter 3: Quick Start This section presents a useful guide for first-time programming of the Model 1108. Follow instructions for installation before attempting to program the Model 1108. Refer to Chapter 2: Installation. 3.1 The Local Keypad Programming is accomplished using the local keypad (shown below, Figure 3-1).

  • Page 32: Quick-Start Programming Steps

    3.3 Quick-Start Programming Steps Step 1: Set Configuration of Inputs The Model 1108 will scan the 8 external inputs and determine if they are N.O. (normally open), N.C. (normally closed), or Temperature. If external sensors are added, make sure they are in their normal positions before proceeding—refer to Chapter 5,...

  • Page 33: Step 2: Set The Id Number

    2. Press ID NUMBER. 3. Using the number keys, enter the digits (up to 16 are permitted) for the ID number. The Model 1108 will recite the digits as they are pressed. 4. Press ENTER. The 1108 will respond: “Enter. ”...

  • Page 34: Step 4: Set Temperature Limits

    Model 1108 User’s Manual 4. Enter the complete telephone number using the number keys. The Model 1108 will recite the digits as they are pressed. 5. Press ENTER. The unit will respond: “Enter. ” 6. Repeat above procedure to program up to eight separate telephone numbers.
  • Page 35 The Model 1108 responds: “Enter low temperature limit. ” Using the number keys, enter a value for low temperature limit. The Model 1108 will recite the digits as they are pressed. If a negative number is required, first press PAUSE, then enter the number.
  • Page 36 Sensaphone ® Model 1108 User’s Manual For a complete explanation of each feature (with illustrations of keystrokes), refer to Chapter 4: Communications Programming and Chapter 5: Alarm Programming. To gain a basic understanding of how the alarm dial-out feature works, refer to this chapter, Section 3.4. For extended information regarding dial-out and related programmable parameters, refer to Chapter 7: Operation.

  • Page 37: Summary Of The Alarm Dial-Out Process

    3.4 Summary of the Alarm Dial-Out Process Action—Response THE MODEL 1108 DETECTS AN ALERT CONDITION An alert condition is not the same as a valid alarm—the condition must continue for the programmed time period, or Recognition Time, before it is recognized as a valid alarm.
  • Page 38 Sensaphone ® Model 1108 User’s Manual...

  • Page 39: Chapter 4: Communications Programming

    4.1 The Unit ID Number The Unit ID Number is the identification number of the Model 1108. This number may be the same as the telephone number where the unit is installed, or it may be designated using any number that best suits your application.

  • Page 40: Interrogating The Id Number

    The Model 1108 will recite the digits as they are pressed. 4. Press ENTER. The Model 1108 will respond: “Enter. ” 4.1.2 Interrogating the ID Number To interrogate the ID number: 1. Press WHAT IS. 2. Press ID NUMBER. The Model 1108 will recite the Unit ID Number programmed.

  • Page 41: Dial-Out Telephone Numbers

    4.2 Dial-out Telephone Numbers The Model 1108 can store up to eight 32-digit phone numbers. These are the numbers that will be called during dial-out. In the event of an alarm, the numbers are dialed sequentially, 1 through 8. Begin programming the first telephone number by assigning it to the key labeled with the number 1 on the keypad, and continue to assign any other telephone numbers in numerical order.

  • Page 42: Interrogating A Dial-Out Telephone Number

    1. Press WHAT IS. 2. Press PHONE NUMBER. 3. Press a number key (from 1 to 8). Model 1108 will recite the corresponding telephone number. If there is no number programmed for a particular key, the unit will respond: “No number. ”...

  • Page 43: Tone Or Pulse Dialing

    4. Press ENTER. The Model 1108 will say “Enter. ” 4.3 Tone or Pulse Dialing The Model 1108 can dial out in pulse or Touch Tone. Select the type of dialing, in either pulse or tone, depending upon the type of service provided by your telephone company.

  • Page 44: Special Dialing Keys

    When interrogating telephone numbers, asterisk (*) is audibly represented by the word “eleven. ” 4. Code CODE instructs the Model 1108 to wait until the call is answered before continuing. When interrogating telephone numbers, CODE is audibly represented by the word “fourteen. ”...

  • Page 45: Incorporating A Pause

    Model 1108 will recite the digit. 5. Press PAUSE. The Model 1108 will “beep. ” 6. Enter the complete telephone number (1 + area code) using the number keys. The Model 1108 will recite the digits as they are pressed. Chapter 4: Communications Programming...

  • Page 46: Incorporating A Pound (#) Or Asterisk (*)

    Sensaphone ® Model 1108 User’s Manual 7. Press ENTER. The Model 1108 will say “Enter. ” 4.4.3 Incorporating a Pound (#) or Asterisk (*) Incorporate a pound or asterisk if it is normally included in telephone number: 1. Press SET.

  • Page 47: Special Dialing To A Beeper Or

    4.4.4 Special Dialing to a Beeper or Pager The following example demonstrates just one solution to programming the Model 1108 for dialing to a beeper or pager. Many other key sequences will also work. Start with steps 1–3 below; next, enter special dialing keys where required for your beeper or pager service.
  • Page 48 4. Enter the complete telephone number using the number keys. The Model 1108 will recite the digits as they are pressed. 5. Press CODE. This instructs the Model 1108 to wait for the telephone call to be answered by the beeper or pager service.
  • Page 49 SET (where the pound is located) or WHAT IS (where the asterisk is located). The Model 1108 will “beep” each time pound or asterisk is pressed. Enter any remaining digits of the telephone number.

  • Page 50: Rings Until Answer

    4.5 Rings Until Answer Rings Until Answer is the programmed number of times the telephone rings before the Model 1108 will answer an incoming call. This can be set from 1 to 15 rings. The default value is 4. 4.5.1 Programming Rings Until Answer To program Rings Until Answer: 1.

  • Page 51: Double Ring Compatibility

    Press ENTER. The Model 1108 will respond : “Enter. ” 4.5.4 Interrogating Double Ring Compatibility To interrogate Double Ring Compatibility: Press WHAT IS. 2. Press SENSOR ON/OFF. The model 1108 will say “0” if Double Ring Compatibility enabled and “1” if it is disabled. Chapter 4: Communications Programming...

  • Page 52: Tad (Telephone Answering Device)

    To enable/disable the TAD feature: 1. Press SENSOR ON/OFF. 2. Press RING/TAD. The Model 1108 will respond: “On. ” (If the Model 1108 says “Off, ” repeat steps 1 and 2 to reactivate TAD.) 4.6.2 Using the TAD Feature 1. Make sure the TAD feature is enabled on the Model 1108.

  • Page 53: No Tad In Use

    4.6.3 No TAD In Use If a telephone answering device is not used on the same telephone line as the Model 1108, make sure that the TAD feature is disabled, or turned off. Only Rings Until Answer programming will determine how incoming calls are answered. For example, if you program Rings Until Answer to 3, incoming calls will be answered in 3 rings.

  • Page 54: Listen-In Time

    The Listen-in Time is the amount of time you can listen to sounds from the Model 1108’s built-in microphone at its installation site. When you call in for a Status Report, the Model 1108 announces Listen-in Time at the end of its first round of status readings, saying, “Listen to the sound level for (programmed time entered).

  • Page 55: Interrogating The Listen-In Time

    4.7.2 Interrogating the Listen-in Time To interrogate the Listen-in Time: 1. Press WHAT IS. 2. Press LISTEN TIME. The Model 1108 will recite the listen time in seconds programmed. 4.8 Call Delay Call Delay is the programmed length of time the Model 1108 waits, following detection of an alarm, before it begins the dial- out sequence.

  • Page 56: Interrogating Call Delay

    The Model 1108 recites the digits as they are pressed. 4. Press ENTER. The Model 1108 responds: “Enter seconds. ” 5. Using the number keys, enter the seconds. The Model 1108 recites the digits as you press them. 6. Press ENTER. The Model 1108 responds: “Enter. ”...

  • Page 57: Local Voice Mute

    4.9 Local Voice Mute When the Model 1108 dials out to report an alarm, it also audibly recites the alarm message at its installation site. The Local Voice Mute command allows you to turn off the voice at the Model 1108’s site during alarm dialouts and status call-ins.

  • Page 58: Interrogating Voice Repetitions

    2. Press VOICE REPS. The Model 1108 will respond: “Enter number. ” 3. Using the number keys, enter a value from 0 to 10. 4. Press ENTER. The Model 1108 will respond: “Enter. ” 4.10.2 Interrogating Voice Repetitions To interrogate Voice Repetitions: 1.

  • Page 59: Intercall Time

    10 seconds to 60 minutes. The default intercall time is 1 minute. If an incoming telephone call is made to the Model 1108 during Intercall Time (in between its dialing of subsequent telephone numbers to report an alarm), it will answer the incoming call and immediately report any existing alarms.

  • Page 60: Interrogating Intercall Time

    The Model 1108 recites the digits as you press them. 4. Press ENTER. The Model 1108 will respond: “Enter seconds. ” 5. Using the number keys, enter the seconds. The Model 1108 recites the digits as you press them. 6. Press ENTER. The Model 1108 responds: “Enter. ”...

  • Page 61: Maximum Number Of Calls (Max Calls)

    4.12 Maximum Number of Calls (Max Calls) The Max Calls feature controls the total number of repeated call- ing attempts by the Model 1108 in the event of an alarm. When an alarm occurs, the dial-out process begins, and continues to cycle through your programmed telephone numbers until a maximum number of calls is reached.

  • Page 62: Interrogating Max Calls

    The Model 1108 will recite the value set for Max Calls. 4.13 The Clock The Model 1108 has a built-in clock. The power-up time is 12 The clock will keep time from 12 current time. It will then keep time from your programmed time.

  • Page 63: Interrogating For The Current Time

    3. Using the number keys, enter the correct time. The Model 1108 will recite the digits as they are pressed. 4. If the time is AM, press the AM key. The Model 1108 will “beep. ” (If the time is PM , there is no key to press—the clock will be automatically set to PM if AM is not set.)

  • Page 64: The Security Code

    2. Press CODE. The Model 1108 will say “Enter security code. ” 3. Using the number keys, enter 4 digits. The Model 1108 says, “OK. ” The keyboard is now locked. If unauthorized persons attempt to set a parameter, an error message, “Error 2, ”...
  • Page 65 Chapter 4: Communications Programming 3. Using the number keys, enter the digits for the code. If the correct code is entered, the Model 1108 will say “OK. ” If the wrong code is entered, the Model 1108 will say “Error 2. ”...
  • Page 66 Sensaphone ® Model 1108 User’s Manual...

  • Page 67: Chapter 5: Alarm Programming

    • Use Exit Delay via Status Report 5.1 Input Configuration In preparing the Model 1108 to sense an alert condition, the inputs must be configured as dry contact (either open or closed) or as temperature inputs. The default setting for input 1 is temperature;...

  • Page 68: Programming Input Configuration

    1. Press STANDBY to place the Model 1108 in Standby mode. 2. Wire sensors to the inputs to the back of the Model 1108 (see Chapter 2, Section 2.10). 3. Press RUN. The red light glows when the Model 1108 returns to Run mode.

  • Page 69: Enable/Disable Inputs

    5.2.2 Verifying Enabled/Disabled Input Status 1. Press WHAT IS. Press STATUS. The Model 1108 audibly recites the current status of every input. In a Status Report, each input is first identified by its input number, followed by a report that specifies parameters currently...

  • Page 70: Input Recognition Time

    If an alert condition begins and then clears within the established Recognition Time, no dial-out will occur. When an alert condition continues beyond the programmed Recognition Time, the Model 1108 initiates dial-out. The default setting for Input Recognition Time is 0 minutes, 3 seconds. 5.3.1 Programming Input Recognition Time 1.

  • Page 71: Interrogating Input Recognition Time

    4. Using the number keys, enter the minutes. For example, to set a Recognition Time of five minutes, simply press “5” on the keypad. The Model 1108 recites the digits as they are pressed. 5. Press ENTER. The Model 1108 responds: “Enter seconds. ”...

  • Page 72: Limits

    -20° to +150° Fahrenheit, or from -30° to 65° Celsius. When temperature limits exceed high or low settings, the Model 1108 will dial out with an alarm message. Default settings are: 10° F for low temperature and 100° F for high temperature.
  • Page 73 The Model 1108 responds: “Enter low temperature limit. ” 4. Using the number keys, enter a value for low temperature limit. The Model 1108 will recite the digits as they are pressed. If a negative number is required, first press PAUSE, then enter the number.

  • Page 74: Disabling Alarm Response To High Or Low

    To disable alarm response to either high or low temperature settings exclusively, enter the maximum temperature limit when programming the selected input. (The Model 1108 will not respond to temperatures encountered at maximum settings or beyond.) Begin by following the key sequence shown in Section 5.4.1, and when prompted to enter the high or low temperature...

  • Page 75: Temperature Scale

    The default temperature scale is Fahrenheit. To change to Celsius: Press SENSOR ON/OFF. 2. Press TEMP. The Model 1108 responds: “Off, ” indicating Celsius scale has replaced Fahrenheit scale. 3. To return to Fahrenheit scale, repeat the key sequence. The Model 1108 responds: “On, ”...
  • Page 76 • To program a positive offset number (up to +10 degrees), enter the number on the keypad. The Model 1108 recites the digits as they are pressed. • To program a negative offset number (up to -10 degrees), first press PAUSE.

  • Page 77: Interrogating Temperature Calibration

    5.7 Obtaining Current Temperature Current temperature readings for each temperature input may be accessed at any time. The Model 1108 recites the input number, and the actual temperature detected by the attached sensor, for all inputs configured as temperature. To obtain current temperature: Press WHAT IS.

  • Page 78: Ac Power Monitoring Enable/Disable

    AC power failure exceeds a programmable span of time (refer to AC Power Failure Recognition Time, Section 5.9). The default setting for AC power monitoring is enabled (on). When disabled, the Model 1108 will not dial out to report power failure. 5.8.1 Enabling/Disabling the AC Power Alarm 1.

  • Page 79: Programming Power Failure Recognition Time

    5.9.1 Programming Power Failure Recognition Time Press SET. Press RECOGNITION TIME. 3. Press POWER. The Model 1108 responds: “Enter minutes. ” Using the number keys, enter the number of minutes. The Model 1108 will recite the digits as they are pressed.

  • Page 80: Interrogating Power Failure Recognition Time

    5.10 Sound Alarm Monitoring This feature allows you to program the level and duration of sound that will cause the Model 1108 to respond to an alarm and dial out. It may be useful to desensitize the Model 1108 to sound...

  • Page 81: Interrogating Sound Sensitivity

    Press SOUND. The Model 1108 responds: “Enter number. ” Using the number keys, enter a value for sound sensitivity. The Model 1108 recites the digits as you press them. Press ENTER. The Model 1108 responds: “Enter. ” 5.10.2 Interrogating Sound Sensitivity Press WHAT IS.

  • Page 82: Recognition Time

    59 seconds. The default value is 8 seconds. Press SET. Press RECOGNITION TIME. Press SOUND. The Model 1108 responds: “Enter seconds. ” Using the number keys, enter the number of seconds. The Model 1108 will recite the digits as they are pressed. Press ENTER.

  • Page 83: High Sound Alarm Enable/Disable

    The Model 1108 monitors sound through the built-in microphone. When the sound level suddenly exceeds the programmed high sound limit, the Model 1108 will respond to an alert condition. The increased sound level must continue throughout the programmed recognition time. The default for high sound alarm is enabled (on).

  • Page 84: Exit Delay

    The Model 1108 is able to suppress and then reset its dial-out function automatically through use of the Status Report. This is especially convenient when an alert condition is created upon exiting a monitored door, and there is no way to cancel from the local keypad.

  • Page 85: Chapter 6: Acknowledgment, Status Report & Remote Access

    • The Status Report on all monitored conditions. 6.1 Alarm Acknowledgment When the Model 1108 dials out with an alarm message, it will request acknowledgment before hanging up. Acknowledgment indicates to the unit that the alarm message has been received.

  • Page 86: Callback Acknowledgment

    The Model 1108 will respond: * “Warning message received by telephone number (last number dialed). ” The Model 1108 will hang up and the dial- out sequence, including any further response to the alarm, will be cancelled.

  • Page 87: Status Report

    • Listen to the message and hang up. • Then call the Model 1108 back on any telephone. You must wait for 10 rings: This signals the Model 1108 to answer your telephone call. (Make sure to call back within the programmed setting for Intercall Time—refer to Chapter 4,...

  • Page 88: Example: Status Report, No Alarms

    ID). ” “The time is 12:15 (or the current time). ” The Model 1108 proceeds with a separate report for each input. Each input identifies itself by reciting the input number. 6.2.1 Example: Status Report, No Alarms Inputs 2, 3, 4, and 6 are configured as dry contact and input 1, 5, 7, and 8 are configured as temperature.

  • Page 89: Example: Status Report, Existing Alarms

    ” “Listen to the sound level for 10 seconds. ” The Status Report repeats once more and the Model 1108 concludes the call by saying: “Have a good day. ” * The “last telephone number dialed” refers to any...

  • Page 90: Example: Status Report, Disabled Inputs

    (Note that to indicate disabled status, only AC power will return two audible “beeps, ” rather than the word “OFF. ” ) When you call the Model 1108 for a Status Report, you hear the following: “Hello, this is telephone number 555-1234.

  • Page 91: Remote Access By Touch-Tone Telephone

    If a Security Code is in effect, the Model 1108 will prompt you with: “Enter Security Code. ” If no Security Code is set, then it will say “O.K.
  • Page 92 ...initiates Listen-In Time for listening to on-site sounds for the programmed time available. Activating Status Report – # (pound), 2 ...initiates a full recitation of the Status Report. Exiting – # (pound), # (pound) ...forces exit. The 1108 says, “Have a good day, ” and hangs ™...

  • Page 93: Chapter 7: Operation

    1108 operates. 7.1 Alarm Detection, Dial-out and Acknowledgment Generally, an alarm event is structured in the following manner: I. The Model 1108 detects an alert condition due to a change at the sensor. II. A valid alarm is recognized. III. Dial-out begins.
  • Page 94 Sensaphone ® Model 1108 User’s Manual I.Model 1108 Detects a Change at the Sensor • Model 1108 detects a change in the monitored condition (from the sensor wired to one of the inputs). This is considered an alert condition, and does not qualify as a valid alarm at this point.
  • Page 95 III. Dial-out Begins • The dial-out process is activated as soon as the Call Delay time expires (if the alarm has not been cancelled at the Model 1108’s installation site.) The dial-out begins with telephone number 1 and proceeds sequentially, through the remaining telephone numbers.
  • Page 96 Model 1108’s installation site, by pressing any key. • When the Model 1108 dials out and the call is answered via Touch-Tone telephone, any alarm may be instantly acknowledged by pressing “555.”...
  • Page 97 IV. The Alarm Is Acknowledged answering device is connected to the same line as the Model 1108 (and TAD is enabled), the Model 1108 will answer on the first ring. First, it recites the Status Report, followed by: “Warning message received by telephone number...(the last number dialed).

  • Page 98: Example: A Dial-Out Telephone Call

    7.2 Example: A Dial-out Telephone Call The following parameters are selected for demonstration purposes: • Model 1108 Unit ID Number is set to 555-5674. It is currently installed at your place of business. • Dial-out Telephone Number 1 is programmed to 555-1234, your home telephone number.

  • Page 99: Chapter 8: Model 1108 Special Editions

    The Sensaphone 1108 CottageSitter also allows you to turn a device on or off using the 1108 keypad or using your touch-tone telephone. You can also inquire about the status of the device during a voice status report.

  • Page 100: Switching The Output Using The Keypad

    Sensaphone ® Model 1108 User’s Manual or enclosure and have wiring performed by a qualified electrician. 8.1.1 Switching the Output using the Keypad To switch the output ON from the keypad: 1. Press STATUS. STATUS CONFIGURE 2. Press 6. CALIBRATE To switch the output OFF from the keypad: 1.

  • Page 101: Heating Up Your Cottage Or Cabin Remotely

    4. To check the present state of the relay press # 2. This initiates a full recitation of the Status Report. At the end of the status report, the Sensaphone will say “Number nine On/Off. ” 8.1.3 Heating up your Cottage or Cabin Remotely If you keep your cottage or cabin open all year around, or if you do not drain your pipes and antifreeze your plumbing, you likely keep your furnace active when you are away but at a very low...
  • Page 102 Sensaphone ® Model 1108 User’s Manual The second thermostat, the one pre-set for your preferred temperature when you arrive at your cottage or cabin, should be located in your normal living space. This would likely be your existing thermostat, already located in a suitable location by your heating professional at the time your furnace was installed.

  • Page 103: Controlling Lights Or Other Devices

    Module (set to momentary contact) in conjunction with the X10 Universal Module to remotely control your electric garage door opener over the telephone—an ideal way of letting in your cottage or cabin service personnel without being on-site. You may also use the X10 technology to send the ON/OFF signal to a furnace or heater if your thermostat is not easy to wire directly.

  • Page 104: Relay Output Specifications

    Sensaphone ® Model 1108 User’s Manual 8.1.6 Relay Output Specifications Rated Load: 2 A at 30 VAC 2 A at 30 VDC Max. Operating Voltage: 30 VAC 30 VDC Max. Operating Current: Max. Switching Capacity: 60 VA 60 W...

  • Page 105: Sensaphone 1108 Businesssitter

    8.2 Sensaphone 1108 BusinessSitter Edition The Sensaphone 1108 BusinessSitter allows you to monitor and check on the status of your facility from any cellular or ordinary telephone. The Sensaphone 1108 BusinessSitter turns a device on when an alarm occurs. You can also inquire about the status of the device during a voice status report.

  • Page 106: Switching The Output Over The Telephone

    Sensaphone ® Model 1108 User’s Manual To switch the output OFF from the keypad: 1. Press STATUS. STATUS CONFIGURE 2. Press 3. INTERCALL TIME 8.2.2 Switching the Output over the Telephone 1. Call the Sensaphone. When the unit answers it will begin reciting a status report.

  • Page 107: Relay Output Specifications

    Chapter 8: Special Editions Figure 3: Activating a Sounder or Strobe on Alarm 8.2.3 Relay Output Specifications Rated Load: 2 A at 30 VAC 2 A at 30 VDC Max. Operating Voltage: 30 VAC 30 VDC Max. Operating Current: Max. Switching Capacity: 60 VA 60 W...

  • Page 108: Sensaphone 1108 Remotecontrol

    The Sensaphone 1108 RemoteControl also allows you to turn a device on or off using the 1108 keypad or using your touch-tone telephone. You can also inquire about the status of the device during a voice status report.

  • Page 109: Switching The Output Over The Telephone

    2. Press 3. INTERCALL TIME 8.3.2 Switching the Output over the Telephone 1. Call the Sensaphone. When the unit answers it will begin reciting a status report. At any time during the call, press a touch-tone. The unit will respond with “OK. ” The Sensaphone is now ready to accept touch-tone commands.

  • Page 110: Controlling Lights Or Other Devices

    8.3.3 Controlling Lights or other devices Using X10 technology, you can remotely activate any electrical device or appliance in your home through your 1108. X10 technology is a suite of control modules that plug into your existing electrical outlets and transmit coded signals to lamps, lights, and appliances to turn them on or off (See Figure 5).

  • Page 111: Relay Output Specifications

    Module (set to momentary contact) in conjunction with the X10 Universal Module to remotely control your electric garage door opener over the telephone—an ideal way of letting in your cottage or cabin service personnel without being on-site. You may also use the X10 technology to send the ON/OFF signal to a furnace or heater if your thermostat is not easy to wire directly.

  • Page 112: Model 1118 Line Seizure Edition

    8.4 Model 1118 Line Seizure Edition The Sensaphone Model 1118 operates identically to the Model 1108 except for the “line seizure” feature. The following is an explanation of the setup procedures unique to the Model 1118. 8.4.1 How Line Seizure Works Line seizure gives the Sensaphone the ability to “seize”...

  • Page 113: Appendix A: Weekly Testing Procedure

    Humidity sensors: Raise the humidity around the sensor by holding a cup of very hot water beneath the sensor. Allow the unit to contact all programmed telephone numbers. This will make sure that the Sensaphone is programmed properly. It will also prepare personnel to respond appropriately when they receive a call from the Sensaphone.
  • Page 114 Allow the unit to dial all programmed telephone numbers. 5) Keep a log of your tests, noting the date and whether the 1108 passed in each category tested. An example of such a log is shown below. (See “Test Log” at the end of this manual.) If you require assistance, call Sensaphone Technical Support at 610-558-2700.

  • Page 115: Appendix B: Troubleshooting

    Most problems with the Model 1108 are easy to identify and quickly corrected, and are found under the following general headings: •...

  • Page 116: Error Messages

    Error Messages Problem 1. The unit says “Error 1.” 2. The unit says “Error 2.” Cause An invalid value has been entered or too much time has passed without entering a value. Programming changes were attempted without unlocking the keypad. Solution Only enter values within the allowed programming range, and make programming...
  • Page 117 Communications / Dial-out: Problem 1. The Model 1108 fails to dial out. Cause The telephone number may be incorrectly programmed. Tone or pulse (the current dialing method) is not compatible with the telephone line on which the Model 1108 is installed.
  • Page 118 The Model 1108 is connected to an incompatible telephone line. Solution The Model 1108 must be connected to a standard (2-wire analog) telephone line, not a digital extension to a phone system. If the unit will not dial out and the factors previously listed have been ruled out, try connecting the unit to a standard residential telephone line.
  • Page 119 Answer is set to equal the number of rings set for the telephone answering device. When calling the Model 1108, and the TAD is disabled, allow the telephone to ring 10 times. Refer to Chapter 6, Section 6.1.3, and Chapter 4, Section 4.6.3.

  • Page 120: Temperature Monitoring

    Temperature Monitoring: Problem Can’t program temperature limits; or the unit won’t read the temperature sensor. The temperature reading is -20° F or -30° C. Temperature reads 150° F or 65° C. Temperature reading is inaccurate. Cause The input isn’t configured to read a tempera- ture sensor.

  • Page 121: Sound Level Monitoring

    Sound Level Monitoring: Problem False high sound alarms occur frequently. High sound does not cause an alarm. Other Monitoring: Problem Alarm status of an alert input is incorrect. False power out alarms Cause The programmed sound sensitivity results in over-sensitivity to non-alarm sound as well as alarm sound.
  • Page 122 Other Monitoring (continued): Problem The Model 1108 does not recognize power failure. The Model 1108 does not recognize any alarm. Cause Batteries are either incorrectly installed or drained. Recognition time setting is too long. Inputs for alarm are disabled. Programmed Recognition Time is too long.
  • Page 123 • Remove the batteries. • Unplug the unit. • Wait one minute for the Model 1108 to completely power down. • Plug in the unit’s AC adaptor into a standard 120 VAC outlet. • Replace the batteries. Refer to Chapter 2, Installation, for additional information on batteries and installation procedures.
  • Page 124 Sensaphone ® Model 1108 User’s Manual...

  • Page 125: Appendix C: Quick Reference

    Appendix C: 1108 QUICK REFERENCE Parameter Description Call Delay Time delay until first call is made Voice Reps Number of times alarm message is repeated over the phone Intercall Time Time delay between phone calls Max Calls Number of calls until unit...
  • Page 126 [CODE] + [4 digit code] [SENSOR ON/OFF] + [PHONE] SPECIAL KEY FUNCTIONS: + the phone number of the 1108 (+ optional [SET/#] Activate Listen-in: [#] + [1] Activate Status Report: [#] + [2] Disconnect: [#] + [#] On or Off...

  • Page 127: Appendix D: Accessories

    Appendix D: Accessories The sensors listed below are available from Phonetics, Inc., and represent the most commonly used input devices. Other dry contact sensors, designed for more specialized applications, may also be used. Commercial or industrial electrical supply houses can provide devices to monitor virtually any condition. For further information, contact Sensaphone Customer Service at 610-558-2700.
  • Page 128 Sensaphone ® Model 1108 User’s Manual...

  • Page 129: Appendix E: Specifications

    Phone Line Protection: Metal Oxide Varistor & self-resetting fuse LED Indicator System LED: On steady when the unit is in RUN mode. LED blinks once every few seconds while in STANDBY mode. Relay Output (1108-CS/BS/RC only) Rated for 2A 30VAC/2A 30VDC maximum.

  • Page 130: Power Supply

    Sensaphone ® Model 1108 User’s Manual Power Supply Power Supply: 120VAC/8VAC 60Hz 12W wall plug-in transformer w/6' cord. Power Consumption: 5 Watts Power Protection: Metal Oxide Varistor Battery Backup: Six size-D alkaline batteries (not included), providing up to 24 hours of back-up time.

  • Page 131: Appendix F: Returning 1108 For Repair

    Appendix F: Returning the Unit for Repair In the event that the Model 1108 does not function properly, we suggest that you do the following: 1) Record your observations regarding the Model 1108’s malfunction. 2) Call the Technical Service Department at 610-558-2700 prior to sending the unit to Sensaphone for repair.

  • Page 133: Test Log

    Test Log Test Log...
  • Page 134 Sensaphone ® Model 1104 User’s Manual...

Table of Contents