Heaters For Mag-Break Controllers - GE Evolution Series E9000 User Manual

Evolution Series E9000 User Manual
Size 5 (Standard and Ambient Comp.)
Motor Full- Heater
Load Amps Number
3-Ph, 3 Heater CR123
109-118 C592A
119-128 C630A
129-138 C695A
139-155 C778A
156-168 C867A
169-184 C955A
Heaters for Mag-Break
The Mag-Break protector is factory adjusted to the
minimum trip setting
To maintain overload, short-circuit, and ground-
fault protection, use the following instructions
to select heaters and to adjust the Mag-Break
trip setting.
For continuous-rated motors with a service factor of
1.15 to 1.25, select the appropriate heaters for the
motor full-load current. For continuous-rated motors
with a service factor of 1.0, multiply the motor full-load
current by 0.9 and use this value to select heaters.
Use the heater table to verify that the Mag-Break and
current limiter rating is correct for the motor full-load
current. Then set the Mag-Break trip setting to the
recommended value.
If the Mag-Break trips during motor startup, increase
the trip setting by one step at a time until the motor
can be consistently started. Do not exceed the maximum
trip setting shown in the heater table.
Overload relay tripping current in 40° C ambient is the
minimum value of heater full-load current multiplied
by 1.25.
Motor Full- Heater
Load Amps Number
3-Ph, 3 Heater CR123
185-200 C104B
201-221 C113B
222-237 C125B
238-262 C137B
263-270 C151B
Controllers
®
Circuit breaker tripping may be an indication that
a fault current has been interrupted. To provide
continued protection against re or shock hazard,
examine all current-carrying parts and other
components of the motor controller and replace
any damaged components. If heater burnout occurs,
the complete overload relay must be replaced.
Size 0 and 1 (Standard)
Motor Full- Heater
Load Amps Number
3-Ph, 3 Heater CR123
.65-.74 C087A
.75-.84 C097A
.85-.92 C109A
.93-1.02 C118A
1.03-1.10 C131A
1.11-1.23 C148A
1.24-1.38 C163A
1.39-1.49 C184A
1.50-1.67 C196A
1.68-1.79 C220A
1.80-1.98 C239A
1.99-2.24 C268A
2.25-2.43 C301A
2.25-2.43 C301A
2.44-2.75 C326A
2.76-3.25 C356A
3.26-3.43 C379A
3.44-4.03 C419A
4.04-4.43 C466A
4.44-4.94 C526A
4.95-5.36 C592A
5.37-5.77 C630A
5.37-5.77 C630A
5.78-6.35 C695A
6.36-6.92 C778A
6.93-7.99 C867A
8.00-8.47 C955A
8.48-9.19 C104B
9.20-10.0 C113B
10.1-10.7 C125B
10.8-12.0 C137B
10.8-12.0 C137B
12.1-12.9 C151B
12.1-12.9 C151B
13.0-15.1 C163B
15.2-16.3 C180B
16.4-17.9 C198B
Size 1
18.0-19.7 C214B
19.8-21.2 C228B
21.3-22.3 C250B
22.4-23.5 C273B
23.6-25.5 C303B
23.6-25.5 C303B
25.6-27.0 C330B
Mag-Break
TEC &
Trip Setting
TECL
Rating
Rec. Max.
3 LO LO
3 LO LO
3 LO 1
3 LO 1
3 LO 2
3 LO 2
3 LO 3
3 LO 4
3 1 4
3 1 5
3 1 6
3 2 7
3 3 8
7 LO 1
7 LO 2
7 LO 3
7 LO 4
7 1 4
7 1 5
7 2 6
7 2 7
7 3 6
15 LO 2
15 LO 2
15 LO 3
15 LO 3
15 1 4
15 1 5
15 1 6
15 2 6
15 2 7
30 LO 2
15 3 8
30 LO 2
30 LO 3
30 LO 4
30 1 4
30 1 5
30 1 6
30 2 7
30 2 8
30 3 8
50 LO 3
50 LO 3
30