Related Manuals for Philips/Magnavox CCW135AT
Summary of Contents for Philips/Magnavox CCW135AT
- Page 1 Color TV with built-in VCR CCZ132AT CCW135AT Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. AUDIO VIDEO STOP/EJECT PLAY F.FWD REC/OTR CHANNEL VOLUME POWER EARPHONE...
- Page 2 Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once.
-
Page 3: Introduction 3
SmartClock is a trademark of Philips Consumer Electronics Company. Copyright 1998 Philips Consumer Electronics Company. All rights reserved. Introduction 3 Helpful Hint • Before doing anything else, record the TV/VCR’s model and serial num-... -
Page 4: Table Of Contents
4 Table of Contents Setting Up Your TV/VCR Introduction ............3 Table of Contents . -
Page 5: Before Using The Tv/Vcr 5
Putting Batteries in the Remote Control Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow. Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid. -
Page 6: Hooking Up The Tv/Vcr
6 Hooking Up The TV/VCR Hook up your TV/VCR using one of the connections shown. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). -
Page 7: Hooking Up The Tv/Vcr
ANT(enna) Jack. • A rod antenna (not supplied) is available from Philips Service Solutions Group. The part number is 4835 303 37006. To order, call 1-800-851-8885. -
Page 8: Using The Swivel Base (Ccw135 Only)
8 Using the Swivel Base (CCW135 only) Caution: Always place the swivel base on a flat surface. Carefully place the TV/VCR upside down and attach the assembled swivel base to the bottom of the TV/VCR as shown. Tighten the screws (supplied) into the holes marked by the arrows. -
Page 9: Turning On The Tv/Vcr 9
Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. Press the POWER button. The TV/VCR will come on and the screen shown below will appear. -
Page 10: Language Selection
10 Language Selection Follow the steps below to change the language of the on-screen displays. Press the MENU button. PRESS > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP SELECT LANGUAGE >... -
Page 11: Automatic Channel Setup 11
Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. Press the MENU button. TO ADJUST PRESS { / B CABLE >... - Page 12 12 Automatic Channel Setup (cont’d) Adding/Deleting Channels Press the MENU button. TO ADJUST PRESS { / B CH123 SAVED > CHANNEL INPUT EXIT PRIM. SETUP VCR PROGRAM VCR SETUP Press the PLAY/ button or the STOP/ CHANNEL, then press the F.FWD/B button. TO ADJUST PRESS { / B CH123 SAVED...
-
Page 13: Setting The Clock 13
There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from your local PBS station. - Page 14 14 Setting the Clock (cont’d) If ON appears beside AUTO CLOCK, press the F.FWD/B button so that OFF appears to the right of AUTO CLOCK, then press the MENU button. If OFF appears beside AUTO CLOCK, press the MENU button. SET MANUAL CLOCK TIME –...
- Page 15 Automatic PBS Channel Selection Press the MENU button. PRIM. SETUP > PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP SELECT LANGUAGE > AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON]...
-
Page 16: Helpful Hints
16 Setting the Clock (cont’d) Press the PLAY/ button or the STOP/ select SET PBS CH. AUTO. Then, press the F.FWD/B button. SET AUTO CLOCK TIME – – : – – DATE – – / – – / – – NOW SEARCHING TO END PRESS EXIT NOW SEARCHING flashes on the TV/VCR screen. - Page 17 Manual PBS Channel Selection Press the MENU button. PRIM. SETUP > PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS Press the PLAY/ button or the STOP/ PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP SELECT LANGUAGE > AUTO PROGRAMMING CH MEMORY REVIEW VOLUME BAR [ON]...
-
Page 18: Setting The Clock
18 Setting the Clock (cont’d) Press the PLAY/ button or the STOP/ select SET PBS CH. MANUAL. Then, press the F.FWD/B button. AUTO CLOCK (PBS) CH – – TIME – – : – – DATE – – / – – / – – SELECT CHANNEL NUMBER TO END PRESS EXIT Use the Number buttons to select your PBS station. -
Page 19: Daylight-Saving Time 19
When the Daylight-Saving Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Saving Time ON or OFF, follow the steps below. Press the MENU button. -
Page 20: Time Zone
20 Time Zone When you set the clock using AUTO CLOCK, specify a time zone in which a local PBS channel is located. The TV/VCR will maintain the clock according to your time zone. Press the MENU button. PRIM. SETUP >... -
Page 21: Front Panel 21
Cassette Compartment Insert a video cassette tape here. Wireless Remote Sensor Receives a signal from your remote control so you can operate the TV/VCR from a dis- tance. STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the pop up menu. -
Page 22: Rear Panel
22 Rear Panel AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR. ANT. ANT(enna) Jack Connect your antenna or cable here. Details are on pages six - seven. Antenna Hole Connect the stem of an indoor antenna here. -
Page 23: Remote Control Buttons 23
SLEEP Button Press to set the sleep timer. Details are on page 37. POWER Button Press to turn on or off the TV/VCR. Number Buttons Use to select channels and to program TV/VCR functions (such as setting the clock). Channels 1 - 9 To select, press 0, then press the channel you want. - Page 24 24 Remote Control Buttons (cont’d) ALT. CH (Alternate Channel) Button Press to return to the TV channel you were viewing immediately before switching to your current channel. CHANNEL o/p Buttons Press to scan through the TV/VCR’s channels. VOLUME o/p Buttons Press to adjust the sound level.
-
Page 25: Adjusting The Picture Controls 25
Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. Press the MENU button. TO ADJUST PRESS { / B > BRIGHTNESS PICTURE COLOR TINT SHARPNESS TV RESET Press the PLAY/ button or the STOP/ the desired control (BRIGHTNESS, for example). Press the REW(ind)/{ button or the F.FWD/B button to adjust the picture control. -
Page 26: On-Screen Status Displays
26 On-Screen Status Displays A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status dis- play will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: Whenever you press the STOP/p button or the PLAY/o but- ton, the status display will appear for five seconds. -
Page 27: Reminder 27
The channel number will remain on-screen at all times when you set REMINDER to ON in the pop up menu. The exception is dur- ing tape playback, Forward and Reverse Searching and Still modes, and when closed captioning is selected (CAPTION in the pop up menu). -
Page 28: Playing
28 Playing Follow the steps below to play a tape. Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab has been removed, playback should start auto- matically. If playback does not start automatically, press the PLAY/ button to start playback. -
Page 29: Recording 29
Read and follow the steps below to record a TV program. Place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button. Press the SPEED button until the desired tape speed appears on the TV/VCR screen. -
Page 30: One-Touch Recording
30 One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: Channels are set up. There is a tape in the TV/VCR. The record tab must be intact. Use the CHANNEL o/p buttons or the Number buttons to select the channel you want to record. -
Page 31: Rerecording (Tape Duplication) 31
AUDIO and VIDEO OUT Jacks on source unit (VCR or Camcorder) VIDEO AUDIO Make the connections shown above, using audio and video cables. (Make sure the source unit is connected to a power source.) The source unit (VCR or camcorder) will play your tape. Insert a prerecorded tape in the source unit. -
Page 32: Timer Recording
32 Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: The clock is set. If not, CLOCK MUST BE SET appears. Channels are set up. - Page 33 Use the Number buttons (1 - 8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not yet been stored). NOTE: If you select a number that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for a few seconds.
- Page 34 34 Timer Recording (cont’d) Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed. Details about tape speed are on page 29. You cannot use the SPEED button at this time.
-
Page 35: Timer Recording
Checking or Clearing Timer Recordings With the TV/VCR on, press the MENU button. Press the PLAY/ button or the STOP/ VCR PROGRAM, then press the F.FWD/B button. Press the PLAY/ button or the STOP/ GRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest num- bered position will appear on-screen. -
Page 36: Defeat Recording
36 Defeat Recording Follow the steps below to prevent accidental recording. Press the MENU button. PRIM. SETUP PRESS > VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS Press the PLAY/ button or the STOP/ VCR SETUP, then press the F.FWD/B button. VCR SETUP >... -
Page 37: Setting The Sleep Timer 37
Use the sleep timer to program the TV/VCR to shut off in a cer- tain amount of time. Press the SLEEP button. The sleep timer display will appear on-screen. (You can not set the sleep timer during a recording.) SLEEP Within five seconds, press the SLEEP button repeatedly to select 30 minutes, 60 minutes, 90 minutes, or 120 min- utes. -
Page 38: Closed Caption
38 Closed Caption When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the pro- gram’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements). - Page 39 Press the STATUS/EXIT button. The type of closed captions you selected at step 3 will appear on-screen. HELLO HELLO Standard Closed Captions WORLD WEATHER WORLD WEATHER 23:00 23:00 CLOUD CLOUD RAIN RAIN 20:00 20:00 4:00 4:00 CLOUD CLOUD LONDON LONDON Half-screen text Closed Caption (cont’d) 39 +100...
-
Page 40: Volume Bar
40 Volume Bar Usually, the volume bar appears when you press the VOLUME o/p buttons. If you do not need it, set the VOLUME BAR to OFF position. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on-screen. -
Page 41: Repeat Play 41
Follow the steps below to program the TV/VCR to play a tape over and over. Press the MENU button. PRESS > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS Press the PLAY/ button or the STOP/ VCR SETUP, then press the F.FWD/B button. VCR SETUP ONE TIME PLAY [ON]... - Page 42 42 A - B Repeat Play Follow the steps below to program the TV/VCR to play the mate- rial between two specified points (A and B) on a tape over and over again. Insert a tape in the TV/VCR. Press the MENU button. PRIM.
-
Page 43: A - B Repeat Play
Press the STATUS/EXIT button to remove the display. A- B REPEAT will appear on-screen. Beneath it, the letter A will flash beside the real-time counter. A-B REPEAT 0:00:00 Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A). -
Page 44: Real-Time Counter Memory
44 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. Press the STATUS/EXIT button. -
Page 45: Automatic Operation Features 45
Automatic Operation Features 45 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. -
Page 46: Playback Options
46 Playback Options Forward and Reverse Searching (SP/LP/SLP) During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. To return to normal playback, press the PLAY/ Super High Speed Searching (LP/SLP) During tape playback, press the F.FWD/B button or the REW(ind)/{ button, then press again. -
Page 47: Specifications / Glossary 47
Specifications General CRT: 13-inch in line gun Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec. Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C) Relative Humidity: 10% to 75% Power requirement: AC 120V, 60Hz... -
Page 48: Helpful Hints
48 Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. -
Page 49: Helpful Hints
The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 21). You can not enter numbers (for example, to program a timer recording) using the front panel buttons. TV/VCR has no power. -
Page 50: Limited Warranty
Philips Consumer Electronics Company. In countries where Philips Consumer Electronics Company does not dis- Philips Service Solutions Group, P.O. Box 555, Jefferson City, Tennessee 37760, (423) 475-8869 TV/VCR COMBINATION tribute the product, the local Philips service organiza-... -
Page 51: Index 51
a-b repeat play ..42 - 43 accessories ....52 ant(enna) jack ...6, 22 audio jack . -
Page 52: Supplied Accessories
Swivel Base Foundation (CCW135 only) (4835 462 17011 Screw (CCW135 only) (4835 502 67054) If any of these items are not included, or if you need to replace an item, contact Philips Service Solutions Group at the address below. Philips Service Solutions Group P.O.