GE G60 Instruction Manual page 370

B.4 MEMORY MAPPING
bitmask element
518 Digital Element 7
519 Digital Element 8
520 Digital Element 9
521 Digital Element 10
522 Digital Element 11
523 Digital Element 12
B
524 Digital Element 13
525 Digital Element 14
526 Digital Element 15
527 Digital Element 16
530 Frequency Rate of Change 1
531 Frequency Rate of Change 2
532 Frequency Rate of Change 3
533 Frequency Rate of Change 4
544 Digital Counter 1
545 Digital Counter 2
546 Digital Counter 3
547 Digital Counter 4
548 Digital Counter 5
549 Digital Counter 6
550 Digital Counter 7
551 Digital Counter 8
680 User-Programmable Pushbutton 1
681 User-Programmable Pushbutton 2
682 User-Programmable Pushbutton 3
683 User-Programmable Pushbutton 4
684 User-Programmable Pushbutton 5
685 User-Programmable Pushbutton 6
686 User-Programmable Pushbutton 7
687 User-Programmable Pushbutton 8
688 User-Programmable Pushbutton 9
689 User-Programmable Pushbutton 10
690 User-Programmable Pushbutton 11
691 User-Programmable Pushbutton 12
F125
ENUMERATION: ACCESS LEVEL
0 = Restricted; 1 = Command, 2 = Setting, 3 = Factory Service
F126
ENUMERATION: NO/YES CHOICE
0 = No, 1 = Yes
F127
ENUMERATION: LATCHED OR SELF-RESETTING
0 = Latched, 1 = Self-Reset
F128
ENUMERATION: CONTACT INPUT THRESHOLD
0 = 17 V DC, 1 = 33 V DC, 2 = 84 V DC, 3 = 166 V DC
B-52
F129
ENUMERATION: FLEXLOGIC TIMER TYPE
0 = millisecond, 1 = second, 2 = minute
F130
ENUMERATION: SIMULATION MODE
0 = Off. 1 = Pre-Fault, 2 = Fault, 3 = Post-Fault
F131
ENUMERATION: FORCED CONTACT OUTPUT STATE
0 = Disabled, 1 = Energized, 2 = De-energized, 3 = Freeze
F133
ENUMERATION: PROGRAM STATE
0 = Not Programmed, 1 = Programmed
F134
ENUMERATION: PASS/FAIL
0 = Fail, 1 = OK, 2 = n/a
F135
ENUMERATION: GAIN CALIBRATION
0 = 0x1, 1 = 1x16
F136
ENUMERATION: NUMBER OF OSCILLOGRAPHY RECORDS
0 = 31 x 8 cycles, 1 = 15 x 16 cycles, 2 = 7 x 32 cycles
3 = 3 x 64 cycles, 4 = 1 x 128 cycles
F138
ENUMERATION: OSCILLOGRAPHY FILE TYPE
0 = Data File, 1 = Configuration File, 2 = Header File
F140
ENUMERATION: CURRENT, SENS CURRENT, VOLTAGE,
DISABLED
0 = Disabled, 1 = Current 46 A, 2 = Voltage 280 V,
3 = Current 4.6 A, 4 = Current 2 A, 5 = Notched 4.6 A,
6 = Notched 2 A
F141
ENUMERATION: SELF TEST ERROR
bitmask
0
1
2
4
5
G60 Generator Management Relay
error
Any Self Tests
IRIG-B Failure
DSP Error
No DSP Interrupts
Unit Not Calibrated
APPENDIX B
GE Multilin