Download  Print this page

Mitsubishi Electric FR-E720-0.1K(SC) Instruction Manual Page 202

Fr-e700 series.
Hide thumbs

Advertisement

Selection of operation mode and operation location
(11) Switching of operation mode by external signals (X65, X66 signals)
When Pr. 79 = any of "0, 2, 6", the operation mode switching signals (X65, X66) can be used to change the PU or External
operation mode to the Network operation mode during a stop (during a motor stop or start command OFF). (Pr. 79 = "6"
Switch-over mode can be changed during operation)
When switching between the Network operation mode and PU operation mode
1)Set Pr. 79 to "0" (initial value) or "6".
2)Set "10" in Pr. 340 Communication startup mode selection.
3)Set "65" in any of Pr. 178 to Pr. 184 to assign the NET-PU operation switching signal (X65) to the terminal.
4)The operation mode changes to the PU operation mode when the X65 signal turns ON, or to the Network operation
mode when the X65 signal turns OFF.
Pr. 340
Pr. 79
Setting
Setting
0
(initial value)
1
2
3, 4
10
6
X12 (MRS)
ON
7
X12 (MRS)
OFF
∗1
NET operation mode when the X66 signal is ON.
∗2
PU operation mode is selected when the X16 signal is OFF. PU operation mode also when Pr. 550 NET mode operation command source selection= "0"
(communication option command source) and the communication option is not fitted.
External operation mode when the X16 signal is ON.
When switching between the Network operation mode and External operation mode
1) Set Pr. 79 to "0 (initial value), 2, 6 or 7". (At the Pr. 79 setting of "7", the operation mode can be switched when the X12
(MRS) signal turns ON.)
2) Set "0 (initial value) or 1" in Pr. 340 Communication startup mode selection.
3) Set "66" in any of Pr. 178 to Pr. 184 to assign the NET-PU operation switching signal (X66) to the terminal.
4) The operation mode changes to the Network operation mode when the X66 signal turns ON, or to the External
operation mode when the X66 signal turns OFF.
Pr. 340
Pr. 79
Setting
Setting
0
(initial value)
1
2
0
3, 4
(initial
value), 1
6
X12 (MRS)
7
X12 (MRS)
∗1
PU operation mode is selected when Pr. 550 NET mode operation command source selection = "0" (communication option command source) and the
communication option is not fitted.
∗2
PU operation mode is selected when the X16 signal is OFF. When the X65 signal has been assigned, the operation mode changes with the ON/
OFF state of the X65 signal.
202
X65 Signal State
ON (PU)
NET operation mode
PU operation mode ∗1
PU operation mode
NET operation mode
External/PU combined operation mode
NET operation mode
PU operation mode ∗1
Switching among the External and
PU operation mode is enabled ∗2
External operation mode
X66 Signal State
ON (NET)
NET operation mode
∗1
PU operation mode
NET operation mode
∗1
External/PU combined operation mode
NET operation mode
∗1
NET operation mode
∗1
ON
External operation mode
OFF
OFF (NET)
∗2
Fixed to PU operation mode
Fixed to NET operation mode
External/PU combined mode fixed
Operation mode can be switched with operation continued
∗2
Output stop in External operation mode
Forcibly switched to External operation mode
OFF (External)
External operation
mode ∗2
Fixed to PU operation mode
External operation
Cannot be switched to PU operation mode
mode
External/PU combined mode fixed
External operation
Operation mode can be switched with
mode ∗2
operation continued
External operation
Output stop in External operation mode
mode ∗2
Forcibly switched to External operation mode
Remarks
Remarks

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric FR-E720-0.1K(SC)

Comments to this Manuals

Symbols: 0
Latest comments: