Table of Contents
Advertisement
Quick Links
- 1 Getting Started Guide
- 2 N1100-On Series Hardware Overview
- 3 N1124T-On/N1124P-On/N1148T-On/ N1148P-On Installation
- 4 Starting and Configuring the N1100-On Series Switch
- 5 Connecting an N1100-On Series Switch to a Terminal
- 6 Performing the N1100-On Series Initial Configuration
- 7 Enabling Remote Management
- 8 Initial Configuration Procedure
- Download this manual
Advertisement
Table of Contents
Related Manuals for Dell N1108T-ON
Summary of Contents for Dell N1108T-ON
-
Page 1: Getting Started Guide
Dell Networking N1108T-ON/N1108P-ON/ N1124T-ON/N1124P-ON/ N1148T-ON/N1148P-ON Switches Getting Started Guide Regulatory Models: E17W and E18W... - Page 2 ___________________ © 2017 Dell Inc. or its subsidiaries. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell Inc.
-
Page 3: Table Of Contents
......Installing in a Rack ....Wall Installation for N1108T-ON and N1108P-ON ..Installing as a Free-standing Switch . - Page 4 ... Example Session ....Dell Easy Setup Wizard Console Example ..Next Steps .
-
Page 5: Introduction
NOTE: Switch administrators are strongly advised to maintain Dell Networking switches on the latest version of the Dell Networking Operating System (DNOS). Dell Networking continually improves the features and functions of DNOS based on feedback from you, the customer. For critical infrastructure, pre-staging of the new release into a non-critical portion of the network is recommended to verify network configuration and operation with the new DNOS version. -
Page 6: Ventilation System
459.37W 240V/50Hz Main PSU 1.97A 459.06W Ventilation System One fan cools the N1108T-ON/N1108P-ON switches, and two fans cool the N1024T-ON/N1024P-ON/N1048T-ON/N1048P-ON switches. The fans are not field replaceable. N1100-ON Series Model Summary Table 1-2. N1100-ON Series Switch Regulatory Numbers Marketing Description... -
Page 7: N1108T-On/N1108P-On Installation
When mounting multiple switches into a rack, mount the switches from the bottom up. 1 Secure the N1108T-ON/N1108P-ON switch in either the Dell Rack Mount Kit as shown in Figure 1-1 or the Dell Tandem Tray Kit as shown in Figure 1-2. Figure 1-1. Dell Rack Mount Kit... - Page 8 Figure 1-2. Dell Tandem Tray Kit 2 Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack mounting holes on the kit line up to the mounting holes in the rack. 3 Secure the kit to the rack with either the rack bolts or cage nuts and cage- nut bolts with washers (depending on the kind of rack you have).
-
Page 9: N1124T-On/N1124P-On/N1148T-On/ N1148P-On Installation
N1124T-ON/N1124P-ON/N1148T-ON/ N1148P-ON Installation Rack Mounting an N1124T-ON/N1124P-ON/ N1148T-ON/ N1148P-ON Switch WARNING: Safety and Regulatory Information Read the safety information in the as well as the safety information for other switches that connect to or support the switch. The AC power connector is on the rear panel of the switch. Installing in a Rack WARNING: Do not use rack mounting kits to suspend the switch from under a... -
Page 10: Wall Installation For N1108T-On And N1108P-On
Make sure that the supplied rack bolts fit the pre-threaded holes in the rack. NOTE: Make sure that the ventilation holes are not obstructed. Wall Installation for N1108T-ON and N1108P-ON To mount the switch on a wall: 1 Make sure that the mounting location meets the following requirements: •... -
Page 11: Installing As A Free-Standing Switch
Installing as a Free-standing Switch NOTE: Dell strongly recommends mounting the switch in a rack. Install the switch on a flat surface if you are not installing it in a rack. The surface must be able to support the weight of the switch and the switch cables. -
Page 12: Stacking Multiple N1124T-On/N1124P-On/ N1148T-On/ N1148P-On Switches
2 Set the switch on a flat surface, and make sure that it has proper ventilation by leaving 5 cm (2 inches) on each side and 13 cm (5 inches) at the back. Stacking Multiple N1124T-ON/N1124P-ON/ N1148T-ON/ N1148P-ON Switches You can stack N1124T-ON/N1124P-ON/N1148T-ON/ N1148P-ON switches up to four switches high using 10G SFP+ ports on the front of the switch. -
Page 13: Starting And Configuring The N1100-On Series Switch
Starting and Configuring the N1100-ON Series Switch The following flow chart provides an overview of the steps you use to perform the initial configuration after the switch is unpacked and mounted. Installation and Configuration Flow Chart Figure 1-5. Getting Started Guide... -
Page 14: Connecting An N1100-On Series Switch To A Terminal
Terminal keys (not Microsoft Windows keys). 3 Connect the USB type B connector on the cable directly to the switch console port. The Dell Networking console port is located on the right side of the front panel and is labeled with a |O|O| symbol. -
Page 15: Connecting An N1100-On Series Switch To A Power Source
NOTE: Console access to the stack manager is available from any console port via the local CLI. Only one USB console session at a time is supported. Connecting an N1100-ON Series Switch to a Power Source CAUTION: Safety and Regulatory Information Read the safety information in the manual as well as the safety information for other switches that connect to or support the switch. -
Page 16: Booting The N1100-On Series Switch
Booting the N1100-ON Series Switch When the power is turned on with the local terminal already connected, the switch goes through a power-on self-test (POST). POST runs every time the switch is initialized and checks hardware components to determine if the switch is fully operational before completely booting. -
Page 17: Performing The N1100-On Series Initial Configuration
• The Dell Networking switch booted successfully. • The console connection was established, and the Dell Easy Setup Wizard prompt appears on the screen of a PC running terminal emulation software. The initial switch configuration is performed through the console port. After... -
Page 18: Initial Configuration Procedure
NOTE: If you do not run the Dell Easy Setup Wizard or do not respond to the initial Easy Setup Wizard prompt within 60 seconds, the switch enters CLI mode. You must reset the switch with an empty startup configuration in order to rerun the Dell Easy Setup Wizard. -
Page 19: Example Session
Example Session This section describes a Dell Easy Setup Wizard session. The following values are used by the example session: • The SNMP community string to be used is public. • The network management system (NMS) IP address is 10.1.2.100. -
Page 20: Dell Easy Setup Wizard Console Example
Dell Easy Setup Wizard Console Example The following example contains the sequence of prompts and responses associated with running an example Dell Easy Setup Wizard session, using the input values listed earlier. After the switch completes the POST and is booted, the following dialog appears: Unit 1 - Waiting to select management unit)>... - Page 21 Dell. You further agree to allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dell's affiliates, subcontractors or business partners.
- Page 22 The wizard automatically assigns the highest access level [Privilege Level 15] to this account. You can use Dell Network Manager or other management interfaces to change this setting, and to add additional management system information later.
- Page 23 Step 2: Now we need to set up your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later. For more information on setting up user accounts and changing privilege levels, see the user documentation.
-
Page 24: Next Steps
If the information is incorrect, enter (N) to discard the configuration and restart the wizard: [Y/N] y Thank you for using the Dell Easy Setup Wizard. You will now enter CLI mode. Applying Interface configuration, please wait... - Page 25 VLANs and spanning tree protocol. Use the Web-based management interface or the CLI to configure the features your network requires. For information about how to configure the switch features, refer to the User Configuration Guide or CLI Reference Guide available on the support site: dell.com/support. Getting Started Guide...
-
Page 26: Nom Information (Mexico Only)
(NOM): Exporter: Dell Inc. One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, S.A. de C.V. Paseo de la Reforma 2620 - 11 Piso Col. Lomas Altas 11950 México, D.F. Ship to: Dell Computer de México, S.A. de C.V. - Page 27 Printed in the U.S.A. Impreso en los EE.UU. Imprimé aux U.S.A. Impresso nos EUA. w w w. d el l .c om | d el l .c om / s up p or t...