Mitsubishi Electric GOT2000 Series Connection Manual page 120

One-touch tuning data (OTS)
External input (DI)
External output (DO)
Motion device (#)
CPU buffer memory access device (U3E0G)
CPU buffer memory access device (U3E1G)
CPU buffer memory access device (U3E2G)
Word device
CPU buffer memory access device (U3E3G)
Refresh data register (RD)
Safety link register (SAW)
Link direct
Word-specified bit devices (except timer, long timer, counter, long
counter, retentive timer, and long retentive timer)
Long timer (current value) (LTN)
Long counter (current value) (LCN)
Long retentive timer (current value) (LSN)
Index register (32 bits) (ZZ)
Double word
Index register (32 bits) (LZ)
device
Lifetime diagnosis (ALD)
Input signal for test operation (for test operation) (TMI)
Forced output of signal pin (for test operation) (TMO)
Set data (for test operation) (TMD)
*1 For the maximum number of devices when an extended SRAM cassette is installed, refer to the following.
➠
*2 Monitoring or writing is not possible in the continuous device designation mode.
*3 For the servo amplifier, if a real number is written to the device, only the integer portion of the number is stored in the device.
If the data type of the servo amplifier device is set to [Real], the value after the writing may differ from the one before the writing.
In addition, the monitoring performance may slow down.
Therefore, select one of the following items for the data type of the device.
• [Signed BIN16]
• [Unsigned BIN16]
• [Signed BIN32]
• [Unsigned BIN 32]
When you use the value of the servo amplifier device, remember that only the integer portion of the value is stored in the device.
To display a real number on the numerical display or numerical input object, set [Format] to [Real] and select [Adjust Decimal
Point Range] in the object setting.
*4 For monitoring the multiple CPU high speed transmission memory, the CPU buffer memory access device (HG) for RCPU is
monitored.
The CPU buffer memory access device (G) is not monitored.
*5 Only reading is possible.
*6 Only writing is possible.
*7 The device No. must be set in multiples of 16.
*8 Use the following devices to write data to the RAM of a servo amplifier.
• PA, PN: 1 to 32
• PB, PE, PF: 1 to 64
• PC, PT: 1 to 80
• PD, PL: 1 to 48
• POS, SPD, ACT, DCT, DWL, AUX: 1 to 255
Use the following devices to write data to the EEPROM of a servo amplifier.
• PA, PN: 1001 to 1032
• PB, PE, PF: 1001 to1064
• PC, PT: 1001 to 1080
• PD, PL: 1001 to 1048
• POS, SPD, ACT, DCT, DWL, AUX: 1001 to 1255
*9 If a bit-specified word device is used in the random read processing, GT SoftGOT2000 or GT Simulator3 uses the value of the bit
device in block No. 0 only.
2 - 36
2.2 MELSEC iQ-R, RnMT/RT, CR800-D (GT21 only)
Device name
*2*3*5
*2*3
*2*3*5
*5
Link register (JnW)
Link special register
(JnSW)
*1*2
*1
*1*2
*2
*2*3*5
*2*3*6
MELSEC iQ-R CPU Module User's Manual (Application)
Setting range
OTS0 to OTS3
DI0 to DI6
DO0 to DO4
#0 to #108287
U3E0G0 to U3E0G268435455
U3E1G0 to U3E1G268435455
U3E2G0 to U3E2G268435455
U3E3G0 to U3E3G268435455
RD0 to RD1048575
SAW0 to SAW9BFF
JnW0 to JnW1FFFF
JnSW0 to JnSW1FF
Setting range of each bit device
LTN0 to LTN2529407
LCN0 to LCN4761215
LSN0 to LSN2529407
ZZ0 to ZZ22
LZ0 to LZ11
ALD0 to ALD1
*2*3*6
TMI0 to TMI2
*2*3*6
TMO0
TMD0 to TMD1
TMD3
Device No.
representation
Decimal number
Hexadecimal number
-
Decimal number