Honeywell AlarmNet 7847i-E Installation And Setup Manual page 33

PROMPTS
Restore Zn6 Y/N
63
(Y)_
Delay Zn6 (secs)
64
(00)_
Rpt Zn6 ONLY if
65
Armed (N)_
Enable Zn7 Y/N
66
(N)_
Zn7 Trigger Type
67
(V+)_
Invert Zn7 Y/N
68
(N)_
Restore Zn7 Y/N
69
(Y)_
Delay Zn7 (secs)
70
(00)_
Rpt Zn7 ONLY if
71
Armed (N)_
Delay Zn8 (secs)
72
(00)_
Use DHCP Y/N
73
(Y)_
NIC IP Address:
74
255.255.255.255_
Subnet Mask:
75
255.255.255.255_
Gateway IP Addr:
76
255.255.255.255_
4204/
ZONE
ENTRY
2-4204
TRIG.
✔ ✔
[Y], [N]
✔ ✔ [01-15]
[00] = no delay
✔ ✔ [Y], [N]
[Y], [N]
4204
only
• (EOLR)
✔
4204
• (V+)
only
• (V–)
✔
[Y], [N]
4204
only
✔ ✔ [Y], [N]
✔ ✔
[01-15]
[00] = no delay
✔
[Y], [N]
2-
[01-15]
4204
[00] = no delay
only
✔ ✔
[Y], [N]
✔ ✔
12 digit:
xxx.xxx.xxx.xxx
✔ ✔
12 digit:
xxx.xxx.xxx.xxx
✔ ✔
12 digit:
xxx.xxx.xxx.xxx
[0.0.0.0.] = not
used
Section 3: Programming the 7847i/7847i-E
OPTIONS
Enables restore reporting for zone 6.
Defines the reporting delay in seconds for zone 6.
Reports alarms on zone 6 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 4 in 4204 mode; zone 8 in 2-4204 mode) is
triggered (armed).
If [N], always reports alarms on zone 6.
Enables alarm reporting for zone 7.
If [N], skip to Prompt 73: "Use DHCP."
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
Inverts the alarm and normal states of the zone
7 trigger; otherwise uses normal input signal.
Enables restore reporting for zone 7.
Zone Trigger mode: This question will only be
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
Defines the reporting delay in seconds for zone 7.
Zone Trigger mode: This question will only be
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
Reports alarms on zone 7 ONLY if the
conditional zone (zone 4 in 4204 mode; zone 8 in
2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 7.
2-4204 mode: If any zone is programmed to
"Report Only if Armed," or if tamper is enabled,
skip to Prompt 73: "Use DHCP."
Defines the reporting delay in seconds for zone 8.
Dynamically allocates the IP addresses
(recommended).
If Private LAN is enabled, skip to Prompt 79:
"Review." Otherwise, skip to Prompt 78: "Enable
Pwr Save."
If [N], uses fixed IP addresses.
Enter the 4-part address for this device. The four
parts of the address must be separated by spaces
(displayed as periods in Review mode).
Enter the 32-bit address mask used to indicate
the portion (bits) of the IP address that is being
used for the subnet address. The four parts of
the address must be separated by spaces
(displayed as periods in Review mode).
Enter the 4-part address assigned to the
Gateway. The four parts of the address must be
separated by spaces (displayed as periods in
Review mode).
DESCRIPTION
3-19