Maintenance; Optional Accessories; Fig.10 - Makita JV101D Instruction Manual

Finishing edges
► Fig.16
To trim edges or make dimensional adjustments, run the
jig saw blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant jig saw
blade wear. The underside of the workpiece can be
greased instead of using a coolant.
Dust extraction
► Fig.17: 1. Hose (optional accessory) 2. Dust cover
Clean cutting operations can be performed by connect-
ing this tool to a Makita vacuum cleaner.
Insert the hose of the vacuum cleaner into the hole at
the rear of the tool.
Lower the dust cover before operation.
NOTE: Dust extraction cannot be performed when
making bevel cuts.
Rip fence
Optional accessory
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing accessories.
Straight cuts
When repeatedly cutting widths of 160 mm or less, use
of the rip fence will assure fast, clean, straight cuts.
► Fig.18: 1. Rip fence (Guide rule)
To install, insert the rip fence into the rectangular hole
on the side of the base with the fence guide facing
down. Slide the rip fence to the desired cutting width
position, then tighten the bolt to secure it.
► Fig.19: 1. Hex wrench 2. Bolt 3. Fence guide 4. Rip
fence (Guide rule)
Circular cuts
When cutting circles or arcs of 170 mm or less in radius,
install the rip fence as follows.
► Fig.20: 1. Rip fence (Guide rule)
1.
Insert the rip fence into the rectangular hole on the
side of the base with the fence guide facing up.
2. Insert the circular guide pin through either of the
two holes on the fence guide. Screw the threaded knob
onto the pin to secure the pin.
► Fig.21: 1. Threaded knob 2. Fence guide 3. Rip
fence (Guide rule) 4. Pin
3.
Slide the rip fence to the desired cutting radius,
and tighten the bolt to secure it in place. Then move the
base all the way forward.
NOTE: Always use jig saw blades No. B-17, B-18,
B-26 or B-27 when cutting circles or arcs.
Anti-splintering device
Optional accessory, only for aluminum base model
CAUTION:
The anti-splintering device cannot
be used when making bevel cuts.
► Fig.22: 1. Base 2. Anti-splintering device
For splinter-free cuts, the anti-splintering device can
be used. To install the anti-splintering device, move the
tool base all the way forward and fit it from the back of
tool base.
When you use the cover plate, install the anti-splintering
device onto the cover plate.
Cover plate
Optional accessory, only for aluminum base model
► Fig.23: 1. Cover plate 2. Base
Use the cover plate when cutting decorative veneers,
plastics, etc. It protects sensitive or delicate surfaces
from damage. Fit it on the back of the tool base.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Jig saw blades
• Hex wrench 3
• Rip fence (guide rule) set
• Anti-splintering device
• Hose (For vacuum cleaner)
• Cover plate
• Makita genuine battery and charger
10 ENGLISH