Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-433PU...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
Assy beforehand when inclines the power supply unit as the right figure. X CONNECTOR (B) Assy SW POWER SUPPLY Module Power Switch (S1) AC Inlet with Filter Power Cord Fig.1 Charged Section and High Voltage Generating Point (Rear View) PDP-433PU...
Page 5
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PDP-433PU...
7. GENERAL INFORMATION ..........................77 7.1 DIAGNOSIS ............................. 77 7.1.1 CONFIGRATION OF THE PC BOARD ....................77 7.1.2 DIAGNOSIS FOR SHUTDOWN AND POWER-DOWN DIAGNOSIS BY LED ........78 7.1.3 DISASSEMBLY ............................. 85 7.2 IC INFORMATION............................ 89 8. PANEL FACILITIES ............................108 PDP-433PU...
1. SPECIFICATIONS Item Model: PDP-433PU 1024 × 768 pixels Number of Pixels Audio Amplifier 12 W + 12 W (10% distortion) Power Requirement AC 120 V, 60 Hz, 318 W (0.6 W Standby) 1070 (W) × 630 (H) × 98 (D) mm [42 (W) ×...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING PDP-433PG Only PDP-433PG Only PDP-433PU Only PDP-433PE Only Except PDP-433PU Except...
Page 9
See Contrast table (2) Vinyl Bag AHG1310 SP Spacer AEC1925 • • • • • (2) CONTRAST TABLE PDP-433PU/KUC, PDP-433PE/WYVI6, PDP-433PE/WYVI6XK and PDP-433PG/TLDPKBR are constructed the same except for the following: PDP-433PE/ PDP-433PE/ PDP-433PG/ Mark No. Symbol and Description PDP-433PU/KUC...
2.7 MIDDLE LAYER SECTION (1) Upper side Upper side Upper side Upper side PDP-433PU...
Page 21
Sub Frame L ANG2517 Sub Frame R ANG2518 NSP 7 Front Chassis HL (43) ANA1699 NSP 8 Front Chassis V (43) ANA1702 FPC Cushion (43) AEB1371 Insulation Sheet C AEC1927 Screw ABA1294 Screw BMZ30P060FMC VR Cushion AEB1374 V Cushion AED1205 PDP-433PU...
Set the slide switches in accordance with applicable model when replacing the MR INTERFACE Assy. S4001 S4004 CBIT_1 CBIT_0 → → PDP-433P → → PDP-433PU S4001 ← → (CBIT_1) PDP-433PE ← → PDP-433PG Note 1 : When there is not S4004, set only S4001. S4004...
Page 27
J114 Earth Wire ADX2709 Screw BMZ30P060FZK SP TERMINAL Assy AWZ6688 J101 13P Housing Wire ADX2768 (2) CONTRAST TABLE PDP-433PU/KUC, PDP-433PE/WYVI6, PDP-433PE/WYVI6XK and PDP-433PG/TLDPKBR are constructed the same except for the following: PDP-433PE/ PDP-433PE/ PDP-433PG/ Mark No. Symbol and Description PDP-433PU/KUC WYVI6...
2.11 FRONT CASE SECTION PDP-433PU Only Foil Side PDP-433PU...
Page 29
Panel Cushion H (43) AED1200 HDTV Label See Contrast table (2) Protect Panel Assy (43) AMR3303 (2) CONTRAST TABLE PDP-433PU/KUC, PDP-433PE/WYVI6, PDP-433PE/WYVI6XK and PDP-433PG/TLDPKBR are constructed the same except for the following: PDP-433PE/ PDP-433PE/ PDP-433PG/ Mark No. Symbol and Description...
See Contrast table (2) NSP 6 Name Label (HD) Gray See Contrast table (2) Bolt Caution Label Gray AAX2928 (2) CONTRAST TABLE PDP-433PU/KUC, PDP-433PE/WYVI6, PDP-433PE/WYVI6XK and PDP-433PG/TLDPKBR are constructed the same except for the following: PDP-433PE/ PDP-433PE/ PDP-433PG/ Mark No. Symbol and Description...
2..BRIDGE B ASSY AWZ6729 2..BRIDGE C ASSY AWZ6730 2..BRIDGE D ASSY AWZ6731 1..ADDRESS FUKUGO ASSY AWV1928 2..ADR CONNECT A ASSY AWZ6678 2..ADR CONNECT B ASSY AWZ6679 2..ADR CONNECT C ASSY AWZ6680 2..ADR CONNECT D ASSY AWZ6681 2..ADR RESONANCE ASSY AWZ6751 PDP-433PU...
Page 33
∗ In case of this unit(433PU, 433PE or 433PG), remove the part that "W" is marked(one part). PDP Service Assy 433 (AWU1069) Wire Saddle Circuit Board Spacer Circuit Board Spacer (AEC1904) (AEC1872) (AEC1872) (There is marking of "P" nearby.) PDP-433PU...
Page 37
0-3.3V swing square wave *LED_R Red LED control signal 5.0V DC RXD0 232C bus 0-5V swing square wave DDC_SCL I2C for DDC 0-5V swing square wave Remote control signal 5.0V DC DDC_SDA I2C for DDC 0-5V swing square wave PDP-433PU...
"5" key "∞" key "∞" key "2" key * "ENTER" "2" key "3" key * "ENTER" "3" key * : Refer to * : Refer to "6.1.1 How to "6.1.1 How to Enter Service Enter Service Factory Mode". Factory Mode". PDP-433PU...
"5" and "∞" keys. Page 11/18, 13/18 Adjustment and setting items of the Plasma Display Note: The actual page structure may be different. Note 1: If the remote control unit for adjustment with the factory (AA5F) code is used. PDP-433PU...
PANEL Version Panel microcomputer version information of the PDP FLASH Version Panel flash ROM version information of the PDP 01: PIONEER 50 inches, 02: PIONEER 43 inches, MONITOR model PDP model information 11: SHARP 50 inches, 12: SHARP 43 inches...
Page 63
ADRK PD (SD) prompted by the abnormal temperature (indicated by 4 blinks DIGITAL-DC/DC CONVERTER DCC PD of the Green LED), and not a record of a PD of the power-supply section. Note: The actual page structure may be different. PDP-433PU...
After adjustment, if the PDP is restarted in the normal mode, the value in W/B table 2 will be used during PAL signal input, and the value in W/B table 1 will be used during NTSC signal input. Note: The actual page structure may be different. PDP-433PU...
Page 65
After the adjustment, if the PDP is restarted in the normal mode, the unit will operate on [ABL VIDEO50] during PAL signal input, and on [ABL VIDEO60 PC] using your adjusted values during NTSC signal input. Note: The actual page structure may be different. PDP-433PU...
Page 66
For 2 seconds after any operation is performed using the buttons on the main unit or the keys on the remote control unit, generation of a mask signal is stopped. During this period, it is possible to change any setting, make any adjustment, or check an external input signal. Note: The actual page structure may be different. PDP-433PU...
Replace the entire X DRIVE Assy. 1. VRN voltage adjustment When replaced 1. Panel white balance adjustment SW POWER SUPPLY Module Y DRIVE Assy X DRIVE Assy DIGITAL VIDEO Assy MR INTERFACE Assy Fig. 1 Configuration of the PC Board (rear side view) PDP-433PU...
PSUS (=GNDH) is a floating GND and its electric potential is different from that of chassis (Y DRIVE Assy) GND. Be sure not to short-circuit PSUS (=GNDH) and another GND, because that may damage the unit. Note : Be sure to measure between specified test points. PDP-433PU...
Page 69
Note: If you perform various adjustments with the RS-232C commands, be sure to execute a "DM0" command (releasing the pulse number limit) first, and after completion of the adjustment, be sure to execute a "DM3" command (pulse number limit: 64%, factory preset value). PDP-433PU...
Page 70
Y DRIVE Assy X DRIVE Assy Adjusting Points PDP-433PU...
6.4.1 RS-232C Commands The panel control items for the PDP-433PU, PE and PG system can be controlled with the RS-232C commands by connecting a PC through a special communication device GGF1428 when the Media Receiver is not connected with the PDP.
Page 72
Schematic Diagram of the special communication device PDP-433PU...
Page 73
MASK 64 Full mask (cyan 444) MASK 65 Full mask (flesh color 43) MASK 66 Full mask (red 620) MASK 67 Full mask (magenta 98) MASK 68 Full mask (sky blue 1_43) * See "6. 4. 2 GET Commands". PDP-433PU...
Page 74
Maximizing the adjustment value UP n Increasing the adjustment value by n VOFFSET ADJUST Vofs adjustment VOLUME Volume VSUS ADJUST Vsus adjustment XSUS B X-SUS-B pulse adjustment XSUS G X-SUS-G pulse adjustment YSUS B Y-SUS-B pulse adjustment YSUS G Y-SUS-G pulse adjustment PDP-433PU...
(Note 1) : If data are output when Reference mode is selected, the same data as the reference data are output as the offset data. (Note 2) : A checksum of 2 bytes is added at the end, but this can be ignored. PDP-433PU...
Page 76
3 byte Wide /FLASH ROM version 3 byte Note: A checksum of 2 bytes is added at the end, but this can be ignored. Display Information Data Model PDP-503MX (initial value) PDP-433MX Module 50 inches Module 43 inches PDP-503HD PDP-433HD PDP-433PU...
Assy ADR CONNECT D Assy BRIDGE C Assy X CONNECTOR (B) MR INTERFACE Assy Assy ADR CONNECT C Assy ADR RESONANCE Assy SUB ADDRESS B Assy ADR CONNECT B Assy BRIDGE D Assy ADR CONNECT A Assy LED Assy PDP-433PU...
Wait another 5 seconds, then recover the unit by setting the MAIN X-DC/DC CONVERTER POWER button to ON. X-DRIVE Power supply Note: After power-down is released, the unit restarts and goes to Standby mode. Address junction Address resonance DIGITAL-DC/DC CONVERTER PDP-433PU...
Page 79
MODULE Expander MR INTERFACE ASSY AUDIO ASSY IC5202 CXA2021S IC4204 SiI861 IC4005 Expander IC4011 Expander MEDIA RECEIVER Note: The figures 1 - 4 indicate the number of times the "STANDBY/ON" LED blinks when shutdown occurs in the corresponding route. PDP-433PU...
Page 80
Sen so r e Temp Cen t e r t ime 4 1 M RESET Mon i t o r Ac u t i me 4 2 M RESET Pu l s e Ac u t i me 1 6 4 RESET PDP-433PU...
Page 81
Block Diagram of the Power Down Signal System ("STANDBY/ON" LED: Blinking in red) PDP-433PU...
Page 82
P.D. by 2.5V undervoltage (= overcurrent) Reference OVP : Over Voltage Protect UVP : Under Voltage Protect OCP : Over Current Protect : Power Down Note 1: The AC200V P.D. circuit is not mounted in the PDP-503PE and PDP-503PU models. PDP-433PU...
Page 84
Similarly, the switches and the semifixed VRs inside the power- 200V AC). supply module must not be adjusted without a special reason. Setting: For the PU model only, the switch is set to 100V, and for other models, it is set to 200V. PDP-433PU...
MENU, ENTER, then POWER Metal keys of the remote control unit in that order. The unit restarts and enters Service Factory mode. Turn off the power using the remote control unit. Then, the unit can be operated normally. PDP-433PU...
Page 86
Assy Metal AUDIO AMP Assy SW Power Supply Module Sub Frame L Sub Frame R ×2 SP TERMINAL Assy ×4 ×2 SW Power Supply Module Remove the DIGITAL VIDEO Assy (Connector,Circuit Board Spacer × 6) Diagnosis DIGITAL VIDEO Assy PDP-433PU...
Page 87
Remove the Front Case 43 (P). Front Case Assy 43 (P) Rear Case Aluminum Materials The hook of the Front Case 43 (P) is fixed with the Rear Case and the aluminum material, as shown in the illustration. PDP-433PU...
Page 88
(Connector, PCB Spacer × 3, Screws × 8) Scan IC Spring (43L) Scan IC Spring (43R) ×2 Reverse the SCAN (A) and SCAN (B) Assemblies. Exchange the ROM if necessary. SCAN (B) Assy ×2 X DRIVE Assy ×6 SCAN (A) Assy PDP-433PU...
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC SN755864APZP, HD64F2328VF, PE1013B, M30624FGAFP, PD6358A, PST9246N, FS781BZB, STK795-470 SN755864APZP (SCAN A ASSY : IC6201 - IC6206, SCAN B ASSY : IC6001 - IC6006) Scan IC Pin Assignment (Top view) PDP-433PU...
Page 90
The high potential circuit power supply which is common to HVO1 - HVO32 − 41, 42, 78, 79 The high potential circuit power supply which is common to HVO33 - HVO64 29, 33, 43, 47 − It is the insulation electrically 77, 80, 83, 96 PDP-433PU...
Page 91
APLP The APL value acquisition trigger signal input VD_31 The V signal input from IC1401 (PD6358) 3.3V power supply Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus PDP-433PU...
Page 92
A clock oscillation child connection terminal NC terminal 3.3V power supply NC terminal A read control terminal from an outside slave device HWRB A wright control terminal to an outside slave device NC terminal NC terminal NC terminal NC terminal NC terminal NC terminal PDP-433PU...
Page 93
The HD signal input from outside Assy (RGB Assy etc.) The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input NC terminal CS_31Y IC1301, IC1401 (PD6358) control signal CS_31X IC1301, IC1401 (PD6358) control signal PDP-433PU...
Page 96
, y l l l u l l u t i s c t i x i f t s i x i f PDP-433PU...
Page 97
Pin Function (2/2) a l l g i l g i l t s i l a i n i l PDP-433PU...
Page 98
PD6358A (DIGITAL VIDEO ASSY : IC1301, IC1401) Picture Improved IC Pin Function (1/7) ) t r ) t i PDP-433PU...
Page 99
) t i f i f ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i PDP-433PU...
Page 100
Pin Function (3/7) ) t r ) t i PDP-433PU...
Page 101
) t i r i f ) t i ) t i ) t i ) t i ) t i f i f ) t i ) t i r i f ) t i PDP-433PU...
Page 102
Pin Function (5/7) ) t i r i f ) t i ) t r PDP-433PU...
Page 103
) t i ) t i ) t i ) t i ) t i f i f ) t i r i f ) t i ) t i ) t i ) t r PDP-433PU...
Page 104
Pin Function (7/7) ) t i ) t i ) t i ) t i ) t i ) t i ) t i PDP-433PU...
Page 105
PST9246N (DIGITAL VIDEO ASSY: IC1208) Drive Protect PLD Block Diagram Pin Assignment (Top View) SOT-25 (TOP VIEW) Pin Function Pin No. Pin name Functions control pin Substate pin GND pin Reset signal output pin pin / voltage detect pin PDP-433PU...
Page 106
Modulated Clock Frequency Output. The center frequency is the same as the input reference FSOUT CMOS/TTL frequency for FS781. Input frequency is multipled by 2X and 4X for FS782 and FS784 respectively. Power Positive Power Supply Power Power Supply Ground PDP-433PU...
Page 107
OUT L PGND 36 N.C. 35 POWER GND DUMMY 34 POWER GND 33 POWER GND 32 POWER GND 31 N.C. 30 PL1 N.C. 28 N.C. 26 PC1 25 PC2 24 PC2 PGND DUMMY TR10 23 N.C. 22 PL2 21 PL2 PDP-433PU...