Area Setting; Air Flow Velocity And Direction Adjustment; ª∞™Π∞ ∆√À ∫∞£∂ ∂•∞Ƒ - Mitsubishi Electric MSZ-FA25VA Operating Instructions Manual

AREA SETTING

To air-condition mainly the
left area of the room
Remote controller button
Press to select LEFT.
Remote controller display
i-see Sensor operation
Installed
Control range
at center
of horizontal air
flow direction.
The vertical air
flow direction
Installed
conforms to the
at left
setting on the re-
mote controller.
(The horizontal
air flow direction
Installed
is controlled in
at right
this range. )
Indoor unit
AREA
display

AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT

AIR FLOW velocity and direction can be selected as required.
■
To change the AIR FLOW velocity, press the
Each time the button is pressed, the fan speed is changed in sequence:
(Low) →
• Use the
• If the operating sound of the air conditioner disturbs your sleep, use the
■
To change the AIR FLOW blowing direction vertically, press the
VANE
Each time the button is pressed, the angle of the horizontal vane is changed in
sequence:
SWING OPERATION
Use the swing operation for the air flow to reach all corners of the room.
Recommended horizontal vane range for more
efficient air-conditioning
Use the
Use position
use positions
adjusting to your requirements.
To air-condition the entire room The
horizontal air flow direction and indoor unit To air-condition mainly the
display are switched according to the room right area of the room
temperature (floor/wall).
Press to select AUTO. Press
FAN
(Med.) → (High) → (Supper High) →
(Super High) notch to cool/heat the room more efficiently.
(Low) notch.
button.
(1) → (2) → (3) → (4) → (SWING) →
(AUTO) position usually.
(1) in the COOL or DRY mode and
(2) to (4) in the HEAT mode when
Movement of the horizontal vane
to select RIGHT.
Horizontal position
• The vane automatically moves to horizontal position.
It will not swing.
NOTE:
Air blows out upper than position (1).
• To constantly change the air flow direction, select
(SWING) with the
When the air flow direction is
set to position (2), (3) or (4)
• After around one hour of operation, the air conditioner
automatically moves the vane to position (1).
button.
To change the air flow direction to the original setting,
operate the VANE button on the remote controller again.
(AUTO)
• The vane does not move to the straight-down
position in the COOL and DRY mode.
• The vane moves intermittently between positions (1)
and (4). The vane stops for a brief period at positions
(1) and (4).
(AUTO)
COOL
DRY NOTE:
• Adjust the AIR FLOW direction using the remote controller. Moving the horizontal vane and vertical vane
manually can cause trouble.
HEAT
• When the operation mode changes in "
to the position in each mode.
COOL/DRY
At the start
of heating
operation
Horizontal
position
• Immediately after the air conditioner starts operating,
the vane stays at horizontal position. Once the air from
the indoor unit becomes sufficiently warm, the vane
moves to position (4).
• Once the air conditioner starts operating, the fan speed
button. increases gradually as the air from the indoor unit gets
VANE
warmer, and continues until the set speed is finally reached.
At the start
of heating
operation
After
Horizontal
around 0.5 Position (1)
position
to 1 hour
• Immediately after the air conditioner starts operating,
the vane stays at horizontal position. Once the air
from the indoor unit becomes sufficiently warm,
the vane moves to the position corresponding to the
set direction of air flow.
• Once the air conditioner starts operating, the fan
speed increases gradually as the air from the indoor
unit gets warmer, and continues until the set speed
is finally reached.
• The vane moves intermittently between positions (2) and (4).
The vane stops for a brief period at positions (2) and (4).
(AUTO)" mode, the horizontal vane is automatically changed
HEAT
When air
Very small becomes
air flow warm...
Position (4)
When air
Very small becomes
air flow warm...
Set position
9