Section 13 : System Commands - Honeywell VISTA-128BPT Installation And Setup Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
User Code
Commands
Programming
Commands
Event Logging
Commands
Wireless System
Commands
Additional
Commands
Output Device
Control Commands
Scheduling
Commands
Access Control
Commands
Master Code + # + 65

Section 13 : System Commands

Add A User Code = User Code + 8 + New User Number + New User's Code
Change a Code = User Code + 8 + User Number + New User's Code
Delete a User's Code = Your User Code + 8 + User Number to Be Deleted + Your Code Again
View User Capability = User's Code + [∗] + [∗]
Set Real-Time Clock (Installer, Master Only) = Code + [#] + 63
Site Initiated Download = User Code + [#] + 1.
Activate Panel initiated Communication Session with Compass via the Dialer = Installer Code +
[#] + 1.
Direct-Wire Download Enable = User Code + [#] + 5.
Enter Program Mode = Installer Code + 8000.
Enter Interactive Program Mode = Installer Code + 8000 + [#] + 93
Exit Program Mode = ∗99 or ∗98.
Event Log Display = Code + [#] + 60 (Installer or Master Only)
Event Log Print = Code + [#] + 61 (Installer or Master Only)
Clear Event Log = Code + [#] + 62 (Installer or Master Only)
House ID Sniffer Mode = Code + [#] + 2 (Installer Only)
Transmitter ID Test = Code + [#] + 3 (Installer Only)
Go/No Go Test = Code + 5 (Test Key)
Partition GOTO
GOTO Home Partition
Panics
View Downloaded Messages
Display All Zone Descriptors
Activate Output Device as Programmed = User Code + [#] + 71.
Activate Output Device as Programmed = User Code + [#] + 72.
Activate Output Device Manually = User Code + [#] + 70.
Activate Output Device or System Event Instantly = User Code + [#] + 77.
Randomize Output Devices = User Code + [#] + 41
Randomize Output Devices Programmed with Activation Times Between 6 PM and 5 AM = User
Code + [#] + 42.
De-activate Randomization = Enter the sequence used to activate randomization.
Installer-Programmed Schedule Events = Installer Code + [#] + 80 (Installer or Master Only).
Temporary Schedule Editing = User Code + [#] + 81 (Installer, Master, Manager Only).
Extend Closing Window = User Code + [#] + 82 (Installer, Master, Manager Only).
End User Output Device Programming = User Code + [#] + 83.
Activate Access Relay for Current Partition = User Code + 0.
Request to Enter/Exit = User Code + [#] + 73.
Request to Enter/Exit at Access Point = User Code + [#] + 74 + Access Point Number.
Change Access Point State = User Code + [#] + 75 + Access Point + State.
Perform a Test of the VistaKey Module = Installer Code + [#] + 78.
Perform an Access Control Card Function = User Code + [#] + 79.
If local programming lockout is set via downloading, programming mode cannot be entered at
the keypad unless Master Code + #65 is entered, which opens up a 24hr window to allow the
installer to enter the program mode. Once the 24hrs has expired the program mode is again
locked out.
User Code + [∗] + Partition Number 0-8.
User Code + [∗] + 0.
[∗] + 1 or A Key (Zone 995).
[∗] + [#] or B Key (Zone 999).
[#] + 3 or C Key (Zone 996).
Press 0 for 5 Seconds.
Press [∗] for 5 Seconds.
13-1