Sony HCD-FX100W Service Manual

Sony HCD-FX100W Service Manual

Hide thumbs Also See for HCD-FX100W:
Table of Contents

Advertisement

QQ
3 7 63 1515 0

SERVICE MANUAL

Ver. 1.2 2005.12
HCD-FX100W is the amplifier, DVD/CD
and tuner section in DAV-FX100W.
This system incorporates with Dolby*1 Digital and
Dolby Pro Logic (II) adaptive matrix surround decoder
and the DTS*2 Digital Surround System.
*1 Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic," and the double-D symbol are trademarks
of Dolby Laboratories.
TE
L 13942296513
*2 Manufactured under license from Digital Theater Systems, Inc.
"DTS" and "DTS Digital Surround" are trademarks of Digital
Theater Systems, Inc.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION:
Amplifier section
Surround mode (reference) music power output
www
.
Sony Corporation
9-879-685-03
Home Audio Division
2005L16-1
Published by Sony Engineering Corporation
© 2005.12
http://www.xiaoyu163.com
HCD-FX100W
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
VIDEO 1, VIDEO 2
With 3 ohm loads, both
channels driven, from
200 – 20,000 Hz; rated
Inputs (Digital)
55 watts per channel
VIDEO 1 (Coaxial)
minimum RMS power,
VIDEO 2 (Optical)
Phones
with no more than 0.7 %
total harmonic distortion
from 250 milli watts to
Super Audio CD/DVD system
rated output.
Laser
Front: 143 W + 143 W
(with SS-TS46)
Center*: 143 W
(with SS-CT46)
Signal format system
Surround*: 143 W + 143
Frequency response (at 2 CH STEREO mode)
W
(with SS-TS46B)
Subwoofer*: 285 W
(with SS-WS42)
x
ao
y
i
http://www.xiaoyu163.com
8
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
Q Q
3
6 7
1 3
SPECIFICATIONS
Sensitivity: 450 mV
Impedance: 50 kilohms
Impedance: 75 ohms
Accepts low-and high-
impedance headphones.
Semiconductor laser
(Super Audio CD/DVD:
= 650 nm)
λ
(CD:
= 790 nm)
Emission duration:
continuous
NTSC
DVD (PCM): 2 Hz to 22
kHz (±1.0 dB)
CD: 2 Hz to 20 kHz (±1.0
dB)
u163
.
2 9
9 4
2 8
Canadian Model
HCD-FX10
CDM69EH-DVBU101
KHM-310CAB/C2NP
1 5
0 5
8
2 9
9 4
Tuner section
System
PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range
87.5 – 108.0 MHz
(100 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
λ
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
— Continued on next page —
m
DVD RECEIVER
co
9 9
US Model
2 8
9 9

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-FX100W

  • Page 1: Service Manual

    3 7 63 1515 0 SERVICE MANUAL US Model Canadian Model Ver. 1.2 2005.12 HCD-FX100W is the amplifier, DVD/CD and tuner section in DAV-FX100W. This system incorporates with Dolby*1 Digital and Model Name Using Similar Mechanism HCD-FX10 Dolby Pro Logic (II) adaptive matrix surround decoder...
  • Page 2 LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 HCD-FX100W 3 7 63 1515 0 Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the bottom exterior.
  • Page 4: Table Of Contents

    HCD-FX100W 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTE 7-6. Schematic Diagram – DMB10 Section (1/4) – ....41 ........... 5 7-7. Schematic Diagram – DMB10 Section (2/4) – ....42 7-8. Schematic Diagram – DMB10 Section (3/4) – ....43 GENERAL ..............
  • Page 5: Servicing Note

    To prevent a malfunction, the system has performed the self- (xx is a number) diagnosis function. u163 ,Contact your nearest Sony dealer or local authorized Sony service facility and give the 5- character service number. Example: E 61 10 http://www.xiaoyu163.com...
  • Page 6: General

    HCD-FX100W SECTION 2 This section is extracted from instruction manual. 3 7 63 1515 0 GENERAL Front panel A Disc slot (40) H x (stop) (41, 80) I X (pause) (41) (remote sensor) (13) C Front panel display (101)
  • Page 7 HCD-FX100W 3 7 63 1515 0 F TOP MENU (45) Remote G C/X/x/c/ENTER (33, 42, 54, 64, 67, 69, 76, 81) have tactile dots.* C/X/x/c H O RETURN (47) I ALBUM –/+ (41, 74) J ANGLE (68) K AUDIO (62) The AUDIO button has a tactile dot.*...
  • Page 8: Disassembly

    HCD-FX100W SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. • The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are completed.
  • Page 9: Top Panel Sub Assy

    HCD-FX100W 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. TOP PANEL SUB ASSY top panel sub assy 2 two flat head screws (TP) 1 two flat head screws (TP) 4 three screws 3 ×...
  • Page 10: Front Panel Assy

    HCD-FX100W 3 7 63 1515 0 3-3. FRONT PANEL ASSY 2 three screws 3 × 8) (+BVTP MD cover screw 3 × 8) (+BVTP 4 wire (flat type) 19p(CN801) screw 3 × 8) (+BVTP front panel assy L 13942296513...
  • Page 11: Mib01 Board, Mib01 Power Board

    HCD-FX100W 3 7 63 1515 0 3-5. MIB01 BOARD, MIB01 POWER BOARD 1 two screws (+BV 3) 5 wire (flat type) 4 MIB01 POWER board 13p(CN5301) 2 connector (CN9002) 3 connector (CN9001) 7 two screws (+BVTP 3 × 8)
  • Page 12: Dmb10 Board, Tx Board

    HCD-FX100W 3 7 63 1515 0 3-6. DMB10 BOARD, TX BOARD 5 wire (flat type) 6 wire (flat type) 28p(CN4801) 11p(CN4501) 4 wire (flat type) 7 connector (CN401) 12p(CN4802) 9 two screws 0 two screws (+BV (+BV 3 wire (flat type)
  • Page 13: Main Board, H/P Board

    HCD-FX100W 3 7 63 1515 0 3-7. MAIN BOARD, H/P BOARD 0 two screws 7 wire (flat type) (+BV 3) 23p(CN507) qa screw 8 wire (flat type) (+BVTP 3 × 14) 11p(CN504) 6 wire (flat type) qs heat sink...
  • Page 14: Dvd Mechanism Deck (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 3-9. DVD MECHANISM DECK (CDM69EH-DVBU101) 3 DVD mechanism deck (CDM69EH-DVBU101) 1 two screws 2 two screws (+BV (+BV L 13942296513 3-10. BASE UNIT (DVBU101) 1 floating screw (DIA. 12) 2 boss 5 boss...
  • Page 15: Optical Pick-Up (Khm-310Cab/C2Np)

    HCD-FX100W 3 7 63 1515 0 3-11. OPTICAL PICK-UP (KHM-310CAB/C2NP) 3 insulator screw optical pick-up (KHM-310CAB/C2NP) 8 insulator 2 insulator screw 4 insulator screw 7 insulator 9 insulator 1 insulator screw 6 insulator L 13942296513 3-12. SW BOARD, BRACKET (TOP) ASSY...
  • Page 16: Relay Board

    HCD-FX100W 3 7 63 1515 0 3-13. RELAY BOARD 4 connector (CN710) – bottom view – 5 connector (CN703) RELAY board 2 four screws (+BVTP2.6) 6 RELAY board 1 Remove five solders. L 13942296513 3-14. MOTOR (STOCKER) ASSY (STOCKER)(M761) 3 two screws (+BVTP2.6)
  • Page 17: Motor (Roller) Assy (Roller)(M781)

    HCD-FX100W 3 7 63 1515 0 3-15. MOTOR (ROLLER) ASSY (ROLLER)(M781) 3 two screws (+BVTP2.6) 2 Remove two solders. 4 ROLLER MOTOR board 5 motor (roller) assy (roller)(M781) 1 belt (roller V) L 13942296513 3-16. MOTOR (MODE) ASSY (MODE)(M771) 3 two screws (+BVTP2.6)
  • Page 18: Rubber Roller (Slider) Assy

    HCD-FX100W 3 7 63 1515 0 3-17. RUBBER ROLLER (SLIDER) ASSY 5 step screw 8 step screw 1 step screw 9 tension 7 rubber roller spring 0 rubber roller (slider 1) assy (slider 2) (slider 4) assy 2 rubber roller...
  • Page 19: Cam (Gear)

    HCD-FX100W 3 7 63 1515 0 3-19. CAM (GEAR) qf cam (gear) : Note 6 gear (mode 5) qd screw 5 screw (PTPWH2.6 × 8) 4 gear (mode 5) qs gear(mode cam) 3 screw (PTPWH2.6 × 8) qa screw (PTPWH2.6 ×...
  • Page 20: Assembly

    HCD-FX100W SECTION 4 3 7 63 1515 0 ASSEMBLY • This set can be assembled in the order shown below. 4-1. HOW TO INSTALL THE CAM (EJECT LOCK) 1 Rotate the cam (BU U/D) fully in the direction of arrow.
  • Page 21: How To Install The Gear (Mode C)

    HCD-FX100W 3 7 63 1515 0 4-3. HOW TO INSTALL THE GEAR (MODE C) 1 Align the mark on the rotary encoder (S771) with the projection of the assy. 2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
  • Page 22: How To Install The Rotary Encorder (S702)

    HCD-FX100W 3 7 63 1515 0 4-5. HOW TO INSTALL THE ROTARY ENCORDER (S702), GEAR (STOCKER COMMUNICATION) 4 gear 5 screw (PTPWH2.6 × 8) (stocker communication) 3 screw 7 two screws (PWH2 × 6) (PTPWH2.6 × 8) 1 rotary encoder...
  • Page 23: Test Mode

    HCD-FX100W SECTION 5 3 7 63 1515 0 TEST MODE 3. Disc Tray Lock Note 1: Regarding the notification symbol “R” The disc tray lock function for the antitheft of an demonstration Because the number of the operating buttons of this product disc in the store is equipped.
  • Page 24 HCD-FX100W Ver. 1.1 3 7 63 1515 0 4-4. MIRROR TIME ADJUSTMENT DVD SECTION [TEST DISC LIST] To enter Mirror Time Adjustment, press 5 “R” button on the remote Be sure to use the DVD disc that matches the signal standards of commander.
  • Page 25 HCD-FX100W 3 7 63 1515 0 (3) Select “5. MIRR time Adjust”. (14) Confirm the same values are displayed. If it is not same, return to step 7. Drive Manual Operation MIRR time Adjust Menu 1. Servo Control 2. Track/Layer Jump 1.
  • Page 26 HCD-FX100W 3 7 63 1515 0 4-5. EXECUTING IOP MEASUREMENT (5) Wait until a hexadecimal number appear. Manual Adjust In order to execute mirror time adjustment, the following standard procedures must be followed. 1. Track Balance Adjust: 2. Track Gain Adjust: (1) In standby mode, press three buttons x , A and 3.
  • Page 27: Electrical Adjustment

    HCD-FX100W SECTION 6 3 7 63 1515 0 ELECTRICAL ADJUSTMENT DIAT SECTION HDMI SECTION DIAT SIGNAL RF LEVEL ADJUSTMENT ADJUSTMENT OF VIDEO SYSTEM This adjustment is performed in order to adjust the transmission [TEST DISC LIST] distance of RF signal for DIAT communication.
  • Page 28 HCD-FX100W Ver. 1.1 3 7 63 1515 0 Procedure: Procedure: 1. Terminate the COMPONENT VIDEO OUT (Y) connector in 1. Conect an oscilloscope to CN105 pin 6 (RFMON) and CN105 75 Ω. pin 3 (GND) on the DMB10 board.
  • Page 29: Diagrams

    HCD-FX100W SECTION 7 3 7 6 3 1 5 1 5 0 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams.
  • Page 30: Block Diagram - Rf Section

    HCD-FX100W 7-1. BLOCK DIAGRAM – RF SECTION – 3 7 6 3 1 5 1 5 0 • Signal Path : CD PLAY YUV0 YUV0 DVDRFIP : DVD PLAY YUV1 YUV1 YUV2 : SACD PLAY YUV2 YUV3 YUV3 DVDA...
  • Page 31: Mib Section

    HCD-FX100W – MIB SECTION – 3 7 6 3 1 5 1 5 0 PO2 - PO9 • Signal Pash : VIDEO 53-55, 58-62 S(2) - S(9) 33 RESET8 : CHROMA 49 S_VSYNC : COMPONENT VIDEO 50 S_HSYNC VIDEO...
  • Page 32: Video Section

    HCD-FX100W – VIDEO SECTION – 3 7 6 3 1 5 1 5 0 J601(1/2) VIDEO1 VIDEO IN VIDEO2 VIDEO IN IC201 IC204 VIDEO AMP, 75Ω DRIVER VIDEO SWITCH 14 2B 6 YIN OUT2 YOUT S VIDEO(DVD ONLY) OUT3...
  • Page 33: Amp Section

    HCD-FX100W – AMP SECTION – 3 7 6 3 1 5 1 5 0 ALRCK ABCK ASDATA0 ASDATA1 ASDATA2 IC506 IC507 DIGITAL AUDIO SD-RAM PROCESSOR SECTION (Page 30) 7-10 72-75 13-16 77-80 18-21 D0-D15 98,99 D0 – D15 24,25...
  • Page 34: Audio Section

    HCD-FX100W – AUDIO SECTION – 3 7 6 3 1 5 1 5 0 IC301 IC108 HEADPHONE STREAM PROCESSOR J801 HPOUTL1 PHONES HPOUTL2 Q507 HPOUTR1 Q806 - 809 MUTING MUTING HPOUTR2 CONTROL IC101 SPEAKER POWER DRIVER D1 – D3, SCK,...
  • Page 35: Main Section

    HCD-FX100W – MAIN SECTION – 3 7 6 3 1 5 1 5 0 IC721 STOCKER MOTOR DRIVE OUT1 M761 (STOCKER) OUT2 IC711 ROLLER MOTOR DRIVE OUT1 M781 OUT2 (ROLLER) IC701 MODE MOTOR DRIVE OUT1 DC/DC M771 OUT2 (MODE)
  • Page 36: Diat Transmit Section

    HCD-FX100W – DIAT TRANSMIT SECTION – 3 7 6 3 1 5 1 5 0 VCC(9V) IC800 IC801 +12V +2.5V +2.5V REG R835 R836 IC804 RF MODULATOR IC802 D/A CONVERTER LEVEL SHIFT 49 LRCK LRCKO 50 BCK BCKO 48 DTIN...
  • Page 37: Printed Wiring Board - Changer Section

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-2. PRINTED WIRING BOARD – CHANGER SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SW(1) BOARD • Semiconductor Location Ref. No. Location D701 RELAY BOARD...
  • Page 38: Schematic Diagram - Changer Section

    HCD-FX100W • See page 70 for IC Block Diagrams. 7-3. SCHEMATIC DIAGRAM – CHANGER SECTION – 3 7 6 3 1 5 1 5 0 RELAY BOARD CN751 CN702 R731 DIODE DIODE I C 7 5 1 D SENSE...
  • Page 39: Printed Wiring Board - Dmb10 Section (Side A)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-4. PRINTED WIRING BOARD – DMB10 SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually.
  • Page 40: Printed Wiring Board - Dmb10 Section (Side B)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-5. PRINTED WIRING BOARD – DMB10 SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC105 IC107...
  • Page 41: Schematic Diagram - Dmb10 Section (1/4)

    HCD-FX100W 7-6. SCHEMATIC DIAGRAM – DMB10 SECTION (1/4) – 3 7 6 3 1 5 1 5 0 FL401 CN401 FB402 FB404 JL4601 JL4602 JL4603 JL4604 FL403 FB403 FB406 JL4605 JL4606 (Page 42, JL4607 JL4608 C402 C403 MAIN JL4609 JL4610 6.3V...
  • Page 42: Schematic Diagram - Dmb10 Section (2/4)

    HCD-FX100W • See page 80 for IC Pin Function Description. • See page 70 for Waveforms. 7-7. SCHEMATIC DIAGRAM – DMB10 SECTION (2/4) – 3 7 6 3 1 5 1 5 0 (Page 43) (Page 41) (Page 41)
  • Page 43: Schematic Diagram - Dmb10 Section (3/4)

    HCD-FX100W 7-8. SCHEMATIC DIAGRAM – DMB10 SECTION (3/4) – 3 7 6 3 1 5 1 5 0 IC103 (EEP ROM) can not be replaced individually. Replace it with DMB10 board assembly for service. (Page 42) (Page 42) C181...
  • Page 44: Schematic Diagram - Dmb10 Section (4/4)

    HCD-FX100W 7-9. SCHEMATIC DIAGRAM – DMB10 SECTION (4/4) – 3 7 6 3 1 5 1 5 0 (Page 42) (Page 41, R225 R223 100k 100k R232 R234 R231 R221 C211 0.033 C209 R230 C233 0.033 0.0047 C212 R233 C215 0.01...
  • Page 45: Printed Wiring Board - Main Section (Side A)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-10. PRINTED WIRING BOARD – MAIN SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D503 D914...
  • Page 46: Printed Wiring Board - Main Section (Side B)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-11. PRINTED WIRING BOARD – MAIN SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 SPEAKER FRONT:ONLY FOR SS-TS46 • Semiconductor CENTER:ONLY FOR SS-CT46 WOOFER:ONLY FOR SS-WS 42...
  • Page 47: Schematic Diagram - Main Section (1/8)

    HCD-FX100W • See page 77 for IC Pin Function Description. • See page 70 for Waveform. 7-12. SCHEMATIC DIAGRAM – MAIN SECTION (1/8) – 3 7 6 3 1 5 1 5 0 CN509 FFC-S-1.0 ( 1 / 8 )
  • Page 48: Schematic Diagram - Main Section (2/8)

    HCD-FX100W 7-13. SCHEMATIC DIAGRAM – MAIN SECTION (2/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (1/8) (Page 47) ( 2 / 8 ) IC515 IC TA7809LS TP517 C595 C596 C597 R704 0.33 47 35V...
  • Page 49: Schematic Diagram - Main Section (3/8)

    HCD-FX100W • See page 71 for IC Block Diagrams. 7-14. SCHEMATIC DIAGRAM – MAIN SECTION (3/8) – 3 7 6 3 1 5 1 5 0 ( 3 / 8 ) R345 R468 R347 R469 EB910 TERMINAL BOARD TP331...
  • Page 50: Schematic Diagram - Main Section (4/8)

    HCD-FX100W • See page 71 for IC Block Diagrams. 7-15. SCHEMATIC DIAGRAM – MAIN SECTION (4/8) – 3 7 6 3 1 5 1 5 0 ( 4 / 8 ) R384 R480 R383 C137 IC106 R120 R128 25V F...
  • Page 51: Schematic Diagram - Main Section (5/8)

    HCD-FX100W • See page 71 for IC Block Diagram. • See page 70 for Waveform. 7-16. SCHEMATIC DIAGRAM – MAIN SECTION (5/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (3/8) (Page 49) ( 5 / 8 )
  • Page 52: Schematic Diagram - Main Section (6/8)

    HCD-FX100W • See page 71 for IC Block Diagrams. 7-17. SCHEMATIC DIAGRAM – MAIN SECTION (6/8) – 3 7 6 3 1 5 1 5 0 MAIN BOARD (4/8) (Page 50) ( 6 / 8 ) C110 0.001 MAIN...
  • Page 53: Schematic Diagram - Main Section (7/8)

    HCD-FX100W 7-18. SCHEMATIC DIAGRAM – MAIN SECTION (7/8) – 3 7 6 3 1 5 1 5 0 CN902 ( 7 / 8 ) L946 TP919 10uH TX BOARD CN802 TP920 (Page 69) MAIN BOARD (6/8) C938 D931 YG906C2R...
  • Page 54: Schematic Diagram - Main Section (8/8)

    HCD-FX100W • See page 70, 72 for IC Block Diagrams. • See page 70 for Waveform. • See page 75 for IC Pin Function Description. 7-19. SCHEMATIC DIAGRAM – MAIN SECTION (8/8) – 3 7 6 3 1 5 1 5 0...
  • Page 55: Printed Wiring Board - Fl/Key Section

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-20. PRINTED WIRING BOARD – FL/KEY SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location D801 D802 D803 D804...
  • Page 56: Schematic Diagram - Fl/Key Section

    HCD-FX100W • See page 70 for IC Block Diagrams. 7-21. SCHEMATIC DIAGRAM – FL/KEY SECTION – 3 7 6 3 1 5 1 5 0 R852 R855 R857 R858 R851 R853 R856 2.2k 2.2k 4.7k 2.2k 4.7k 2.2k TP833...
  • Page 57: Printed Wiring Board - Led / H/P Section

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-22. PRINTED WIRING BOARD – LED / H/P SECTION – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location PHONES Ref. No. Location D811...
  • Page 58: Schematic Diagram - Led / H/P Section

    HCD-FX100W 7-23. SCHEMATIC DIAGRAM – LED / H/P SECTION – 3 7 6 3 1 5 1 5 0 R833 R867 TP843 4.7k R834 R835 R836 R837 R838 R839 R863 R866 TP841 2.2k 2.2k 4.7k L813 CN803 S815 S810...
  • Page 59: Printed Wiring Board - I/O Section (Side A)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-24. PRINTED WIRING BOARD – I/O SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC201 IC203...
  • Page 60: Printed Wiring Board - I/O Section (Side B)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-25. PRINTED WIRING BOARD – I/O SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 AUDIO IN MONITOR VIDEO 1 VIDEO IN COMPONENT...
  • Page 61: Schematic Diagram - I/O Section

    HCD-FX100W • See page 73 for IC Block Diagrams. • See page 70 for Waveform. 7-26. SCHEMATIC DIAGRAM – I/O SECTION – 3 7 6 3 1 5 1 5 0 CN101 R659 TP626 TP625 TP627 L601 IC603 TORX141L...
  • Page 62: Printed Wiring Board - Mib01 Section (Side A)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-27. PRINTED WIRING BOARD – MIB01 SECTION (SIDE A) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 CN601 HD MI (DVD ONLY) • Semiconductor Location Ref.
  • Page 63: Printed Wiring Board - Mib01 Section (Side B)

    HCD-FX100W • See page 29 for Circuit Boards Location. 7-28. PRINTED WIRING BOARD – MIB01 SECTION (SIDE B) – :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 • Semiconductor Location Ref. No. Location IC111 IC607...
  • Page 64: Schematic Diagram - Mib01 Section (1/3)

    HCD-FX100W • See page 85 for IC Pin Function Description. 7-29. SCHEMATIC DIAGRAM – MIB01 SECTION (1/3) – 3 7 6 3 1 5 1 5 0 IC509 HY57V161610ETP-7 CL502 C516 0.01 R5452 4.7k C520 C512 C505 C513 6.3V 6.3V...
  • Page 65: Schematic Diagram - Mib01 Section (2/3)

    HCD-FX100W • See page 88 for IC Pin Function Description. 7-30. SCHEMATIC DIAGRAM – MIB01 SECTION (2/3) – 3 7 6 3 1 5 1 5 0 C543 0.033 JL501 R527 R509 C541 R526 3.3k 0.33 C539 C540 C556...
  • Page 66: Schematic Diagram - Mib01 Section (3/3)

    HCD-FX100W • See page 70 for Waveform. 7-31. SCHEMATIC DIAGRAM – MIB01 SECTION (3/3) – 3 7 6 3 1 5 1 5 0 R696 C627 0.01 C620 0.01 R612 R664 C611 0.01 R690 C607 0.01 C625 C629 C621 C623 0.22...
  • Page 67: Printed Wiring Board - Mib01 Power Section

    HCD-FX100W 7-32. PRINTED WIRING BOARD – MIB01 POWER SECTION – 7-33. SCHEMATIC DIAGRAM – MIB01 POWER SECTION – 3 7 6 3 1 5 1 5 0 • See page 29 for Circuit Boards Location. :Uses unleaded solder. IC901...
  • Page 68: Printed Wiring Board - Tx Section

    HCD-FX100W • See page 29 for Circuit Boards Location. :Uses unleaded solder. 7-34. PRINTED WIRING BOARD – TX SECTION – 3 7 6 3 1 5 1 5 0 I/O BOARD CN603 (Page 60) CN803 IC804 IC805 1 3 9 4 2 2 9 6 5 1 3...
  • Page 69: Schematic Diagram - Tx Section

    HCD-FX100W • See page 74 for IC Block Diagrams. • See page 70 for Waveform. 7-35. SCHEMATIC DIAGRAM – TX SECTION – 3 7 6 3 1 5 1 5 0 IC B/D IC800 CN802 IC TA7809LS TP803 L807...
  • Page 70 HCD-FX100W • IC Block Diagrams • Waveforms 3 7 6 3 1 5 1 5 0 – DMB10 Board – – MIB01 Board – – MAIN Board – – RELAY Board – – FL Board – IC102 6 (DVDRFIP)
  • Page 71 HCD-FX100W 3 7 63 1515 0 IC101,102,105,106,107 CXD9775M GVDD B GVDD GVDD B BST B DVDD DREG DREG GND 1 PVDD B GATE PWM BP 2 PVDD B RECEIVER DRIVE OUT B TIMING GND 3 OUT B CONTROL DGND &...
  • Page 72 HCD-FX100W 3 7 63 1515 0 IC505 LC89056W-E AUDIO C BIT PA/PB DETECT DETECT EMPHA SAMPLING FREQUENCY MICROCOMPUTER INTERFACE XSEL LOCK XOUT CLOCK DETECT XMCK 19 DVDD MODE0 MODE 18 DGND SELECT MODE1 XSTATE DGND DATAO DVDD LRCK DOSEL0...
  • Page 73 HCD-FX100W 3 7 63 1515 0 – I/O Board – IC203 NJM2235V (TE2) IC601 MC14052BDR2 IN 1 BUFFER SW 1 IN 2 BIAS SW 2 VIN 3 IC201 MM1623BFBE S-DC OUT VCC1 VCC2 S1/S2 L 13942296513 150kΩ BIAS 200Ω...
  • Page 74 HCD-FX100W 3 7 63 1515 0 – TX Board – IC801 TK11225CMCL-G CONTROL CIRCUIT CONSTANT OVER HEAT & CURRENT OVER CURRENT SOURCE PROTECT BANDGAP REFERENCE IC804 CXD4016R L 13942296513 48 47 46 45 44 41 40 39 38 37 36...
  • Page 75 HCD-FX100W 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC506 CXD9862R (DIGITAL AUDIO PROCESSOR) Pin No. Pin Name Description — Ground terminal XRST System reset signal input from the system controller “L”: reset EXTIN Master clock signal input terminal (not used)
  • Page 76 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description WMD0 External memory wait mode setting terminal (fixed at “H” in this set) PAGE2 External memory page selection signal output terminal (not used) — Ground terminal 52, 53...
  • Page 77 HCD-FX100W 3 7 63 1515 0 MAIN BOARD IC509 M30622MGP-A14FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP SCDT/ Digital amp (IC108, 110) data output DIAT SDATA DAMP SHIFT/ Digital amp (IC108, 110) data output DIAT SCLK XSCEN Voltage control for amp...
  • Page 78 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description DRIVE_RST(EN) Driver signal reset DRIVE_OCP(DIAG) Digital amp (power driver) diag OVERFLOW1 Over flow status1 of digital amp (IC110) OVERFLOW2 Over flow status2 of digital amp (IC108 to 110)
  • Page 79 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description — Ground KEY0 Key input 0 VREF Reference Voltage (+3.3V) Power supply (+3.3V) M-ST/WMUTE WMUTE signal output L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 80 HCD-FX100W 3 7 63 1515 0 DMB10 BOARD IC102 CXD9804R (CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description AGND — Terminal Ground DVDA AC coupled input path A DVDB AC coupled input path B...
  • Page 81 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description Not Used Not Used Not Used MAMUTE MAMUTE signal output to System Controller (IC509) DVDD18 — Power Supply (+1.8V) 53 to 58 IOA 2 to 7 Address bus 2 to 7 output to PROM (IC101)
  • Page 82 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description DQMO DQM0 signal output to SD-RAM (IC104) DQS0 DQM signal input Data bus 7 from SD-RAM (IC104) DVSS — Terminal Ground 117, 118 RD 6, 5 Data bus 6, 5 from SD-RAM (IC104) DVSS —...
  • Page 83 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description LIMSW LIMSW signal output to Optical pick-up OCSW SEN signal input from System Controller (IC509) VCLK System clock output CKSW — Not Used Reset signal output to VIDEO DAC...
  • Page 84 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Description SDPIF SPDIF output RFGND18 — Terminal Ground RFVDD18 — Power Supply (+1.8V) ZTALO Oscillator output signal ZTALI Oscillator input signal JITFO RF jitter meter output JITFN Negative input of operation amplifier for RF jigger meter PLLVSS —...
  • Page 85 HCD-FX100W 3 7 63 1515 0 MIB01 BOARD IC503 CXD9837R (PROGRESSIVE SCAN CONVERTER) Pin No. Pin Name Desciption OVDD — Positive supply voltage (+3.3V) for Pad Ring CLKI System clock input (27MHz) TEST7 Test purpose only (must be connected to ground)
  • Page 86 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Desciption OVSS — Digital ground for Pad Ring Address output port for SDRAM Address output port for SDRAM Address output port for SDRAM Address output port for SDRAM OVSS —...
  • Page 87 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Desciption RFFO MPEG flag output port (not used) Data input/output of MPU interface Clock inputt of MPU interface System reset input (negative) OVSS — Digital ground for Pad Ring CVDD —...
  • Page 88 HCD-FX100W 3 7 63 1515 0 MIB01 BOARD IC507 CXD9836R (PIXEL RESOLUTION CONVERTER) Pin No. Pin Name Desciption — Digital ground XTCK1 Test purpose only (must be connected to ground) Test purpose only (must be connected to VDDE) XTST...
  • Page 89 HCD-FX100W 3 7 63 1515 0 Pin No. Pin Name Desciption — Digital ground OVDDE2 — Digital positive supply voltage (+3.3V) for Pad Ring 93 to 95 QR7 to QR9 R data output Vertical sync output Horizontal sync output...
  • Page 90: Exploded Views

    HCD-FX100W SECTION 8 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 91: Front Panel Assy Section

    HCD-FX100W 3 7 63 1515 0 8-2. FRONT PANEL ASSY SECTION supplied supplied supplied not supplied L 13942296513 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-585-417-21 WINDOW (FL) 1-828-336-11 WIRE (FLAT TYPE) (15 CORE)
  • Page 92: Chassis Section-1

    HCD-FX100W 3 7 63 1515 0 8-3. CHASSIS SECTION-1 not supplied not supplied not supplied not supplied chassis section-2 L 13942296513 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1074-640-A DTP-005//K(A)(UC) 0 106...
  • Page 93: Chassis Section-2

    HCD-FX100W Ver. 1.2 3 7 63 1515 0 8-4. CHASSIS SECTION-2 supplied supplied not supplied DVD mechanism deck section F901 supplied L 13942296513 supplied supplied not supplied supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No.
  • Page 94: Dvd Mechanism Deck Section-1 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-5. DVD MECHANISM DECK SECTION-1 (CDM69EH-DVBU101) S702 M761 L 13942296513 DVD mechanism deck section-2 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-725-13 STOCKER MOTOR BOARD 4-239-699-01 PULLEY 3-087-053-01 +BVTP2.6 (3CR)
  • Page 95: Dvd Mechanism Deck Section-2 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-6. DVD MECHANISM DECK SECTION-2 (CDM69EH-DVBU101) DVD mechanism deck section-3 DVD mechanism deck section-4 L 13942296513 optical pick-up section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-727-13 SW (1) BOARD 3-087-053-01 +BVTP2.6 (3CR)
  • Page 96: Dvd Mechanism Deck Section-3 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-7. DVD MECHANISM DECK SECTION-3 (CDM69EH-DVBU101) not supplied supplied not supplied supplied supplied L 13942296513 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-040-01 SPRING (DISC STOPPER), TORSION 4-240-039-01 LEVER (DISC STOPPER) 4-992-069-01 SCREW (+PTPWH) (M2) (DIA.
  • Page 97: Dvd Mechanism Deck Section-4 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-8. DVD MECHANISM DECK SECTION-4 (CDM69EH-DVBU101) supplied L 13942296513 M781 DVD mechanism deck section-5 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4954-626-1 LEVER (ROLLER) ASSY 4-240-041-01 SPRING (SLIDER 2), TENSION 4-239-666-01 GEAR 3-087-053-01 +BVTP2.6 (3CR)
  • Page 98: Dvd Mechanism Deck Section-5 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-9. DVD MECHANISM DECK SECTION-5 (CDM69EH-DVBU101) L 13942296513 DVD mechanism deck section-6 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-020-01 GEAR (TIMING) 4-239-699-01 PULLEY 4-239-708-02 BELT (FRONT), TIMING...
  • Page 99: Dvd Mechanism Deck Section-6 (Cdm69Eh-Dvbu101)

    HCD-FX100W 3 7 63 1515 0 8-10. DVD MECHANISM DECK SECTION-6 (CDM69EH-DVBU101) M771 not supplied L 13942296513 supplied S771 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-239-693-02 CAM (GEAR) 4-241-731-01 SHUTTER (A), LEVER 1-686-723-13 SENSOR BOARD...
  • Page 100: Optical Pick-Up Section (Khm-310Cab/C2Np)

    HCD-FX100W 3 7 63 1515 0 8-11. OPTICAL PICK-UP SECTION (KHM-310CAB/C2NP) L 13942296513 not supplied Ref. No. Part No. Description Remark 0 601 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP) 3-087-599-01 INSULATOR SCREW 3-088-372-01 INSULATOR u163 http://www.xiaoyu163.com...
  • Page 101: Electrical Parts List

    HCD-FX100W Ver. 1.1 SECTION 9 DMB10 3 7 63 1515 0 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms.
  • Page 102 HCD-FX100W DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FL107 1-234-494-21 FILTER, EMI REMOVAL (SMD) C209 1-164-677-11 CERAMIC CHIP 0.033uF C210 1-162-970-11 CERAMIC CHIP 0.01uF FL108 1-234-494-21 FILTER, EMI REMOVAL (SMD)
  • Page 103 HCD-FX100W DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R143 1-216-809-11 METAL CHIP 1/10W R1504 1-400-244-11 BEAD, FERRITE (CHIP) (1608) R1505 1-216-833-11 METAL CHIP 1/10W R144 1-216-864-11 SHORT CHIP...
  • Page 104 HCD-FX100W DMB10 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN802 1-784-867-21 CONNECTOR, FFC (LIF (NON-ZIF)) 15P RB108 1-234-370-21 RES, NETWORK 22 (1005X4) CN804 1-506-468-11 PIN, CONNECTOR 3P RB111 1-234-795-21 RES, NETWORK 0X4 (2010)
  • Page 105 HCD-FX100W 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark H/P BOARD C201 1-164-156-11 CERAMIC CHIP 0.1uF ********* C202 1-162-964-11 CERAMIC CHIP 0.001uF < CAPACITOR > C203 1-125-972-91 ELECT 100uF C204...
  • Page 106 HCD-FX100W 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > R233 1-218-285-11 METAL CHIP 1/10W R241 1-218-285-11 METAL CHIP 1/10W CN101 1-568-828-11 CONNECTOR, FFC 9P R601 1-216-833-11 METAL CHIP...
  • Page 107 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S802 1-786-763-11 SWITCH, TACTILE (VOLUME +) C105 1-164-346-11 CERAMIC CHIP S804 1-786-763-11 SWITCH, TACTILE (FUNCTION) C106 1-164-346-11 CERAMIC CHIP S805...
  • Page 108 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C323 1-164-156-11 CERAMIC CHIP 0.1uF C211 1-136-177-00 FILM C324 1-164-156-11 CERAMIC CHIP 0.1uF C212 1-136-177-00 FILM C325 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 109 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C603 1-104-658-91 ELECT 100uF C527 1-107-726-91 CERAMIC CHIP 0.01uF C606 1-107-826-11 CERAMIC CHIP 0.1uF C528 1-107-826-11 CERAMIC CHIP 0.1uF C608...
  • Page 110 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D944 6-500-288-11 DIODE EK19LF-F7 C960 1-100-566-91 CERAMIC CHIP 0.1uF 0 C963 1-117-698-51 CERAMIC 680PF 250V D945 8-719-083-67 DIODE UDZSTE-1720B 0 C964...
  • Page 111 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC951 6-707-743-01 IC TA76L431S (TPE6, Q) Q111 8-729-600-22 TRANSISTOR 2SA1235-F Q112 8-729-600-22 TRANSISTOR 2SA1235-F < JACK > Q301 8-729-120-28 TRANSISTOR...
  • Page 112 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R202 1-220-942-11 METAL CHIP 1/4W R343 1-216-864-11 SHORT CHIP R205 1-220-942-11 METAL CHIP 1/4W R345 1-216-833-11 METAL CHIP 1/10W R346...
  • Page 113 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R474 1-216-864-11 SHORT CHIP R554 1-216-809-11 METAL CHIP 1/10W R475 1-216-864-11 SHORT CHIP R555 1-216-830-11 METAL CHIP 5.6K 1/10W R556...
  • Page 114 HCD-FX100W MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R624 1-216-833-11 METAL CHIP 1/10W R707 1-216-809-11 METAL CHIP 1/10W R627 1-216-809-11 METAL CHIP 1/10W R709 1-216-833-11 METAL CHIP 1/10W...
  • Page 115 HCD-FX100W Ver. 1.2 MAIN MIB01 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 R919 1-216-836-11 METAL CHIP 1/10W < VARISTOR > 0 R920 1-216-821-11 METAL CHIP 1/10W 0 VDR901 1-805-482-11 VARISTOR...
  • Page 116 HCD-FX100W MIB01 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C554 1-127-715-91 CERAMIC CHIP 0.22uF C5502 1-117-370-11 CERAMIC CHIP 10uF C5504 1-216-864-11 SHORT CHIP C555 1-162-964-11 CERAMIC CHIP 0.001uF C556 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 117 HCD-FX100W MIB01 3 7 63 1515 0 Ref. No. Ref. No. Part No. Part No. Description Description Remark Remark Ref. No. Part No. Description Remark R516 1-216-864-11 SHORT CHIP R681 1-216-864-11 SHORT CHIP R682 1-216-840-11 METAL CHIP 1/10W R526...
  • Page 118 HCD-FX100W MIB01 MIB01 POWER MODE MOTOR RELAY 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5452 1-216-829-11 METAL CHIP 4.7K 1/10W * CN9002 1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P R5453 1-216-829-11 METAL CHIP 4.7K...
  • Page 119 HCD-FX100W RELAY ROLLER MOTOR SENSOR ST ENCODER 3 7 63 1515 0 STOCKER MOTOR SW(1) SW(2) SW(3) SW(4) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN703 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P 1-686-728-13 SW (2) BOARD...
  • Page 120 HCD-FX100W 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C834 1-107-826-11 CERAMIC CHIP 0.1uF C835 1-162-966-11 CERAMIC CHIP 0.0022uF 10% L812 1-456-509-11 INDUCTOR 10uH C836 1-164-156-11 CERAMIC CHIP 0.1uF C837 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 121 HCD-FX100W 3 7 63 1515 0 Ref. No. Part No. Description Remark MISCELLANEOUS ************** 1-828-336-11 WIRE (FLAT TYPE) (15 CORE) 1-828-952-11 WIRE (FLAT TYPE) (9 CORE) 1-787-331-11 FAN, D.C. 0 106 1-783-531-91 CORD, POWER 1-830-552-11 WIRE (FLAT TYPE) (24 CORE)
  • Page 122 HCD-FX100W 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Table of Contents