Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Philips ST7SB
Summary of Contents for Philips ST7SB
-
Page 1: User Guide
ST7SB Socket Board User Guide Release 1.1.1 November 2004 Ref: DOC-MDT0005... - Page 2 USE IN LIFE SUPPORT DEVICES OR SYSTEMS MUST BE EXPRESSLY AUTHORIZED. STMicroelectronics PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF STMicroelectronics. As used herein: 1. Life support devices or systems are those which (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in...
-
Page 3: Table Of Contents
Chapter 1: Introduction ......... . 2 About the user manuals... -
Page 4: Chapter 1: Introduction
1 - Introduction INTRODUCTION The ST7SB socket board complements any ST7 programming tool that is equipped for in-circuit programming (ICP) via a 10-pin ICC cable. For these programming tools and emulators, the socket board provides the sockets required to program ST7 FLASH microcontrollers without having to install them on an application board. -
Page 5: About The User Manuals
ST7SB Socket Board User Guide Note: The ST7SBxx socket board is meant to program small numbers of microcontrollers (i.e. prototypes in the development stage). For mass production programming, we recommend using the appropriate gang, or automated programmer. About the user manuals... -
Page 6: Chapter 2: Delivery Check List
All the connection cables you will need to connect to your PC are provided with the programming tool that you are using to connect to your PC. 4/12 ST7SB Socket Board User Guide Figure 1 ) is delivered with one power supply. -
Page 7: Chapter 3: Configuring And Connecting To Your Socket Board
ST7SB Socket Board User Guide CONFIGURING AND CONNECTING TO YOUR SOCKET BOARD This chapter tells you how to set up and connect to your socket board for programming. It includes how to: • Configure the power supply for your ST7 •... - Page 8 = (50 / V OTHER OTHER Example to obtain a V = (50 / 4) - 10 = 2.5 KΩ OTHER Figure 3: Installing serial resistors ST7SB Socket Board User Guide ) -10 of 4V: OTHER Figure 3 Figure 2...
-
Page 9: Connect To The Socket Board
ST7SB Socket Board User Guide Connect to the socket board All ST7 programming tools that use a 10-pin ICC cable (including the ST7-STICK) can be connected to the HE-10 type ICC connector on top of your socket board. However, when using the ST7-STICK you can also connect via the Female HE10 connector on the bottom of your Socket board. - Page 10 You are ready to program your ST7 from the STVP7 interface on your host PC. 8/12 Figure 5: Male and female HE10 connector Figure 4 , inset A . Figure 4 , inset B . ST7SB Socket Board User Guide ...connects to the female connector on the bottom of your ST7SB socket board.
-
Page 11: Appendix A Safety Requirements
ST7SB Socket Board User Guide APPENDIX A SAFETY REQUIREMENTS • Any tester, equipment, or tool used at any production step, or for any manipulation of semiconductor devices, have its shield connected to ground. • The product must be placed on a conductive table top, made of steel or clean aluminum, or covered by an antistatic surface (superficial resistivity equal to or higher than 0.5 MΩ/cm... -
Page 12: Product Support
STMicroelectronics, from the component manufacturer or from a distributor. To help you find what you need, a listing of accessories for ST development tools is available on the ST internet site, www.st.com/mcu. 10/12 ST7SB Socket Board User Guide Contact List , below. -
Page 13: Contact List
ST7SB Socket Board User Guide Contact List Canada and East Coast STMicroelectronics Lexington Corporate Center 10 Maguire Road, Building 1, 3rd floor Lexington, MA 02421 Phone: (781) 402-2650 West coast STMicroelectronics, Inc. 1060 E. Brokaw Road San Jose, CA 95131... - Page 14 STMicroelectronics. Purchase of I C Components by STMicroelectronics conveys a license under the Philips I C system is granted provided that the system conforms to the I Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -...