Mitsubishi Electric PQRY-P72TLMU-A Manual page 7

1. SPECIFICATIONS
Model
Power source
Cooling capacity (Nominal) *1 (208/230V)
Temp. range of cooling
(208/230V)
Heating capacity (Nominal) *2
Temp. range of heating
Indoor unit connectable
Sound pressure level (measured in anechoic room)
Refrigerant piping diameter
Module Set
Module
External finish
External dimension HxWxD
Net weight
Heat exchanger
Compressor
Circulating water *3
Protection devices
Minimum Circuit Ampacity(MCA)
Maximum Overcurrent Protection(MOP)
Refrigerant
Pipe between unit and
distributor
Drawing
Standard attachment
Optional parts
Remarks
Note: *1 Nominal cooling conditions (subject to JIS B8615-1)
Indoor: 81degF D.B./ 66degF W.B. (27degC D.B./ 19degC W.B.) 68degF D.B. (20degC D.B.)
Water Temp.: 86degF (30degC)
Pipe length: 24-9/16ft.(7.5m)
Level difference: 0ft.(0m)
* Due to continuing improvement, above specifications may be subject to change without notice.
© 2017 Mitsubishi Electric US, Inc.
Btu/h
kW
Power input kW
Current input A
Indoor W.B.
Circulating water *3
Btu/h
kW
Power input kW
Current input A
Indoor D.B.
Circulating water *3
Total capacity
Model / Quantity
dB <A>
High pressure in.(mm)
Low pressure in.(mm)
in.
mm
lbs(kg)
Type
G
Water volume in plate
I
psi
Water pressure Max.
MPa
Type
Manufacturer
Starting method
Motor output kW
Lubricant
G/h
G/min(gpm)
Water flow rate m / h
3
L/min
cfm
psi
Pressure drop
kPa
G/h
Operating volume
G/min(gpm)
range
m / h
3
High pressure protection
Inverter circuit(comp)
Compressor
A
A
Type x original charge
Control
High pressure in.(mm)
Low pressure in.(mm)
External
Wiring
Document
Accessory
Details on foundation work, duct work, insulation work, electrical wiring, power source switch,
and other items shall be referred to the Installation Manual.
The ambient temperature of the Heat Source Unit needs to be kept below 104°F DB(40° C DB).
The ambient relative humidity of the Heat Source Unit needs to be kept below 80%.
The Heat Source Unit should not be installed at outdoor. Mount a strainer (more than 50
meshes) at the water inlet piping of the unit.
The Heat Source twinning kit (low pressure) should be connected to the low pressure side of the
heat source unit.
Mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
A field provided flow switch is required for minimum flow protection on each module, field
installed and wired to TB8 (terminal 3-4).
*3 If using Circulating water temperatures that are between 23 and 50° F, Dip switch 3-9 must be
turned on and glycol must be used in the water loop to prevent freezing down to 5° F.
*2 Nominal heating conditions (subject to JIS B8615-1)
68degF (20degC)
25ft.(7.6m)
0ft.(0m)
PQRY-P-T(S)LMU, Y(S)LMU (April 2017 Ver2)
PQRY-P144TSLMU-A
3-phase 3-wire 208 / 230 ±10% 60Hz
144,000
42.2
7.11
21.9 / 19.8
59~75° F (15~24° C)
50~113° F (10~45° C)
160,000
46.9
7.45
22.9 / 20.7
59~81° F (15~27° C)
50~113° F (10~45° C)
50~150% of heat source unit capacity
P06~P96/1~36
7/8 (22.2) Brazed
1-1/8 (28.58) Brazed
PQRY-P72TLMU-A
Galvanized steel sheets
43-5/16 x 34-11/16 x 21-11/16
1,100 x 880 x 550
380 (172)
Plate
1.32
5
290
2
Inverter scroll hermetic compressor
AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Inverter
4.3
MEL32
1,522 + 1,522
25.4 + 25.4
5.76 + 5.76
96 + 96
3.4 + 3.4
3.48
24
793 + 793 ~ 1,902 + 1,902
13.2 + 13.2 ~ 31.7 + 31.7
3.0 + 3.0 ~ 7.2 + 7.2
High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
Over-heat protection, Over-current protection
Over-heat protection
13 / 12
20 / 20
R410A x 11 lbs + 1 oz (5.0 kg)
Indoor LEV and BC controller
5/8 (15.88) Brazed
-
KJ94T151
KE94C966
Installation Manual
Details refer to External Drw
Heat Source Twinning kit: CMY-Q100CBK2
Joint: CMY-Y102SS-G2, CMY-Y102LS-G2, CMY-Y202S-G2, CMY-R160-J1
Main BC controller: CMB-P108, 1010, 1013, 1016NU-GA1, 108, 1010, 1016NU-HA1
Sub BC controller: CMB-P104, 108NU-GB1, CMB-P1016NU-HB1
49
PQRY-P72TLMU-A
43-5/16 x 34-11/16 x 21-11/16
1,100 x 880 x 550
380 (172)
Plate
1.32
5
290
2
Inverter
4.3
MEL32
3.48
24
13 / 12
20 / 20
R410A x 11 lbs + 1 oz (5.0 kg)
5/8 (15.88) Brazed
3/4 (19.05) Brazed
KE94C966
Unit converter
BTU/h =kW x 3,412
cfm =m /min x 35.31
3
lb =kg / 0.4536
* Above specification data is subject to rounding
variation.
WR2-7