Preparing For Surround Sound; Speaker Settings - Kenwood VR-6060 Instruction Manual

Preparing for surround sound

Speaker settings

To enable you to obtain optimum enjoyment from the receiver's listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
POWER
ON/STANDBY SETUP MULTI CONTROL
POWER
(For KRF-V8060D)
SET UP
1
Turn on the power to this receiver by pressing the POWER
ON/OFF and ON/STANDBY ( ) (for VR-6060 only) key or
RECEIVER ( ) key.
2
Press the SETUP key to enter the SET UP mode and press
M M M M M /? ? ? ? ? keys for the following displays.
1 SP SETUP
2 TEST TONE
3 SP DISTANCE
4 SETUP END
The Surround Back and Subwoofer speakers are displayed as
follows:
1 6ch AMP SB
2 6ch AMP SW
Use the MULTI CONTROL knob or Joystick to select the speakers.
Press the SETUP key to proceed to the following selection.
3
Select a speaker system.
1 Select the SP SETUP and press the SETUP key again, so that
the subwoofer setting indication "SUBW ON" appears.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG 96kHzfs
L C SW R
LFE
SL S SB SR
2 Use the M M M M M / ? ? ? ? ? keys to select the appropriate settings.
1 SUBWOOFER
2 FRONT
3 CENTER
4 SURROUND
5 SURROUND BACK
6 SW RE-MIX
•VR609/20-28/EN
RECEIVER
Joystick
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 RDS
THX
ACTIVE EQ. MATRIX
RTY
Surround EX
DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
21
3 Use the MULTI CONTROL knob or Joystick to adjust the sub-
woofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver is
ON.
2 SUBW OFF : Subwoofer setting mode to the receiver is
OFF.
• The initial setting is "SUBW ON".
• When the setting "SUBW OFF" is selected, the front speakers are
automatically set to "FRNT LARGE" and the procedure skips to
step 6.
• When subwoofer output sound is required, select "FRNT NOR-
MAL".
(For VR-6060 only)
When you operate on the remote control unit.
1 Press the SET UP key repeatedly until "SUBWOOFER" scrolls
from right to left in the display of the remote control unit.
2 Press the Joystick to select "SUBW ON", then press the
ENTER key.
4 Press the M M M M M / ? ? ? ? ? keys to accept the setting.
• The front speakers setting indication "FRNT" appears.
SP MUTE OPTICAL 6CH INPUT CINEMA EQ.
AUTO DETECT
ACTIVE EQ.
A B CLIP
COAXIAL ANALOG 96kHzfs DSP MODE
L C SW R
LFE
SL S SB SR
5 Use the MULTI CONTROL knob or Joystick to select the
appropriate front speakers setting.
1 FRNT LARGE
: Large front speakers are connected
to the receiver.
2 FRNT NORMAL
: Average size front speakers are con-
nected to the receiver.
• For "FRNT LARGE" selection, no sound will be heard from
SUBWOOFER even when it is set to ON. However, if you select
CINEMA EQ when subwoofer is selected, you will be able to
hear sound from the subwoofer.
When in STEREO mode, the sound goes directly to front
speaker.
6 Press the M M M M M /? ? ? ? ? keys to accept the setting.
• The center speaker setting indication "CENTER" appears.
7 Use the MULTI CONTROL knob or Joystick to select the
appropriate center speaker setting.
If you selected "LARGE" as the front speakers setting.
1 CENTER LARGE
: A large center speaker is con-
nected to the receiver.
2 CENTER NORMAL : An average size center speaker is
connected to the receiver.
3 CENTER OFF
: Center speaker setting mode to
the receiver is OFF.
If you have selected "NORMAL" as the front speakers setting.
1 CENTER NORMAL : Center speaker setting mode to
the receiver is ON.
2 CENTER OFF
: Center speaker setting mode to
the receiver is OFF.
10/24/01, 10:36 PM
DTS. DOLBY DIGITAL STEREO NEO:6 RDS
THX
MATRIX
RTY
Surround EX
DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
Continued to next page
21
EN