Sony HCD-X1V Service Manual
Sony HCD-X1V Service Manual

Sony HCD-X1V Service Manual

Super audio cd/dvd receiver
Table of Contents

Advertisement

SERVICE MANUAL

Ver. 1.0 2006.07
• HCD-X1V is the amplifier, super audio CD/DVD
system, tuner and video section in DAV-X1V.
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
This system perfectly decodes 5.1 channel
signal, but you cannot add other commercially
available surround speakers.
* Manufactured under license from Dolby
Laboratories.
"Dolby", "Pro Logic", and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license from Digital Theater
Systems, Inc. "DTS" and "DTS Digital Surround"
are registered trademarks of Digital Theater
Systems, Inc.
Sony Corporation
9-887-304-01
Home Audio Division
2006G05-1
Published by Sony Techno Create Corporation
© 2006.07
Model Name Using Similar Mechanism
DVD Mechanism Type
Optical Pick-up Block Name
AUDIO POWER SPECIFICATIONS
for the US model
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION
(FTC Output Power):
Front: 38 W/ch 4 ohms at
150 -20,000 Hz,
0.7% THD
Front surround: 38 W/ch
4 ohms at 150 -20,000 Hz,
0.7% THD
Subwoofer: 38 W/ch
4 ohms at 25 - 150 Hz,
0.7 % THD
Amplifier section
Front
Power output (rated):
70 W + 70 W (4 ohms,
1 kHz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
1 kHz, 10 % THD)
Front surround*
Power output (rated):
70 W + 70 W (4 ohms,
1 kHz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
1 kHz, 10 % THD)
Subwoofer
Power output (rated):
70 W + 70 W (4 ohms,
100 Hz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
100 Hz, 10 % THD)
* Depending on the sound field settings and the source,
there may be no sound output.
SUPER AUDIO CD/DVD RECEIVER
HCD-X1V
Canadian Model

SPECIFICATIONS

Inputs (Analog)
VIDEO1, VIDEO2, TV, AUDIO IN
Sensitivity: 450 mV (ATT
ON), 250 mV (ATT OFF)
Impedance: 50 kilohms
Inputs (Digital/COAXIAL)
VIDEO1 , VIDEO2
Impedance: 75 ohms
Super Audio CD/DVD system
Laser
Semiconductor laser
(Super Audio CD/DVD:
λ = 650 nm)
(CD:λ = 790 nm)
Emission duration:
continuous
Signal format system
For North American models:
NTSC
For European models:
NTSC/PAL
Tuner section
System
PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range
For North American models:
87.5 – 108.0 MHz
(100 kHz step)
For European models:
87.5 – 108.0 MHz
(50 k Hz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
– Continued on next page –
US Model
AEP Model
UK Model
NEW
CDM69EH
KHM-310CAB or
KHM-313CAB

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-X1V

  • Page 1: Service Manual

    Canadian Model AEP Model UK Model Ver. 1.0 2006.07 • HCD-X1V is the amplifier, super audio CD/DVD system, tuner and video section in DAV-X1V. This system incorporates with Dolby* Digital Model Name Using Similar Mechanism and Dolby Pro Logic (II) adaptive matrix...
  • Page 2 PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE Fig. A. Using an AC voltmeter to check AC leakage. FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Table Of Contents

    3-19. SENSOR Board, Rotary Encoder (Mode) (S771) ... 22 diagnosis function. ,Contact your nearest Sony ASSEMBLY dealer or local authorized Sony service facility and give the 5- 4-1. How To Install The Cam (Eject Lock) ......23 character service number.
  • Page 4: Servicing Notes

    HCD-X1V SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP 7-19. Printed Wiring Board BLOCK OR BASE UNIT – MAIN Board (Conductor Side) – ......... 51 The laser diode in the optical pick-up block may suffer electrostatic 7-20. Schematic Diagram – MAIN Section (1/6) – ....52 break-down because of the potential difference generated by the 7-21.
  • Page 5 HCD-X1V NOTE OF REPLACING THE EEPROM (IC103 and S-FORCE FRONT SURROUND OPERATION CHECK IC706) ON THE DMB12 BOARD When complaint by the effect of the sound field, check as follows EEPROM (IC103 and IC706) on the DMB12 board cannot exchange and confirm abnormality is not found in the set.
  • Page 6: About This Manual

    HCD-X1V Music discs encoded with CD-RW/CD-R About This Manual (audio data) copyright protection (MP3 files) technologies • The instructions in this manual describe the (JPEG files) controls on the remote. You can also use the This product is designed to play back discs that controls on the system if they have the same or conform to the Compact Disc (CD) standard.
  • Page 7 HCD-X1V HOW TO IDENTIFY OPTICAL PICK-UP BLOCK There are two kinds of OPTICAL PICK-UP BLOCK in this set. When replacing the OPTICAL PICK-UP BLOCK, make sure which OPTICAL PICK-UP BLOCK it is following the “How to Identify” in the figure shown below.
  • Page 8 HCD-X1V POWER BOARD SERVICE POSITION Please place a sheet for insulation. POWER board Note : The Power board can be removed individually. NOTE ON WIRE PROCESSING BETWEEN AMP BOARD AND POWER BOARD Note : To prevent a contact with the components on the primary side of power supply, the wires should be routed in front of the wire (flat type) (19 core) and reshaped.
  • Page 9 HCD-X1V MAIN BOARD SERVICE POSITION 1 wire (flat type) (9 core) (US, Canadian models) 3 Remove the Back Panel, wire (flat type) (11 core) and then the MAIN board. (AEP, UK models) (CN303) 2 connector (CN1000) Please place a sheet for insulation.
  • Page 10 HCD-X1V DVD MECHANISM DECK (CDM69EH) SERVICE POSITION In checking the DVD mechanism deck (CDM69EH), prepare jig (extension cable J-2501-248-A: 1.00 mm Pitch, 27 cores, Length 300 mm). DVD mechanism deck (CDM69EH) wire (flat type) (27 core) MAIN board (CN621) connect jig (extension cable J-2501-248-A) to the MAIN board (CN621) and wire (flat type) (27 core).
  • Page 11: General

    HCD-X1V SECTION 2 This section is extracted from instruction manual. GENERAL Front panel A "/1 (on/standby) H Front surround indicator B Disc slot I Front panel display J Z (eject) (remote sensor) D N (play) K DISC 1-5/indicator E x (stop)
  • Page 12 HCD-X1V Front panel display About the indications in the front panel display A Lights up when the sleep timer is set. H Displays system’s status such as chapter, title, or track number, time B Current surround format (Except for information, radio frequency, playing JPEG and Super Audio CD) status, sound field, etc.
  • Page 13: Disassembly

    HCD-X1V SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.
  • Page 14: Top Panel, Side Panel

    HCD-X1V Note: Follow the disassembly procedure in the numerical order given. 3-2. TOP PANEL, SIDE PANEL 8 top panel 1 two screws (BVTT3 × 8) 5 connector (CN804) 2 side panel (L) 7 three screws (BV/ring) 6 screw (BV/ring) 3 two screws (BVTT3 ×...
  • Page 15: Power Board

    HCD-X1V 3-4. POWER BOARD 1 three connectors (CN902, CN903, 2 four screws CN904) (BVTT3 × 6) 3 screws (BVTT3 × 8) 4 cover (L) 5 POWER board 1 connector (CN905) 3-5. AMP BOARD 6 two screws (BV3) 2 two screws 4 bracket (DMB) (BVTT3 ×...
  • Page 16: Rear Panel Block

    HCD-X1V 3-6. REAR PANEL BLOCK 8 three screws (BVTT3 × 6) 7 bracket (DMB) 5 two screws q; two screws (BVTT3 × 6) qd two bosses (BV/ring) 2 wire (flat type) (27 core) (CN621) 3 wire (flat type) (19 core)
  • Page 17: Dvd Mechanism Deck (Cdm69Eh)

    HCD-X1V 3-8. DVD MECHANISM DECK (CDM69EH) 7 DVD mechanism deck 3 screw (BVTT3 × 6) (CDM69EH) 6 four screws (BV3) 2 bar 4 two screws (BV3) 5 cover (CDM) 1 two screws (BVTP3 × 8) 4 screw (BV3) 1 two screws (BVTP3 ×...
  • Page 18: Optical Pick-Up Block (Khm-310Cab Or Khm-313Cab)

    HCD-X1V 3-10. OPTICAL PICK-UP BLOCK (KHM-310CAB or KHM-313CAB) 2 insulator screw 5 optical pick-up block (KHM-310CAB or KHM-313CAB) 4 insulator 1 flexible flat cable (24 core) 2 insulator screw 2 insulator screw 4 insulator 4 insulator 2 insulator screw 4 insulator 3-11.
  • Page 19: Relay Board

    HCD-X1V 3-12. RELAY BOARD – bottom view – 4 connector 1 Remove thirteen solders of (CN702) CN704, CN705, CN706, CN707, CN708. 4 connector 4 connector (CN703) (CN710) CN705 CN704 CN707 CN706 CN708 2 four screws (BVTP2.6) RELAY board 5 RELAY board 1 Remove five solders of rotary encoder (stocker position) (S702).
  • Page 20: Motor (Stocker) Assy (Roller) (M781)

    HCD-X1V 3-14. MOTOR (STOCKER) ASSY (ROLLER) (M781) 3 two screws (BVTP2.6) 2 Remove two solders of motor (roller) assy (roller) (M781). 4 ROLLER MOTOR board 2 Remove two solders of connector (CN781) . 5 motor (roller) assy (roller) (M781) 1 belt (roller V) 3-15.
  • Page 21: Rubber Roller (Silder) Assy, Sub Chassis

    HCD-X1V 3-16. RUBBER ROLLER (SLIDER) ASSY, SUB CHASSIS 5 step screw 8 step screw 1 step screw 9 tension 7 rubber roller spring 0 rubber roller (slider 1) assy (slider 2) (slider 4) assy 2 rubber roller 6 tension spring...
  • Page 22: Cam (Gear)

    HCD-X1V 3-18. CAM (GEAR) qf cam (gear) Note: Refer to assembly (Section 4: page 23). 6 gear (mode 5) qd screw 5 screw (PTPWH2.6 × 8) 4 gear (mode 5) qs gear (mode cam) 3 screw (PTPWH2.6 × 8) Note: Refer to assembly (Section 4: page 24).
  • Page 23: Assembly

    HCD-X1V SECTION 4 ASSEMBLY • This set can be assembled in the order shown below. 4-1. HOW TO INSTALL THE CAM (EJECT LOCK) 1 Rotate the cam (BU U/D) fully in the direction of arrow. 2 Engage the gear (eject lock) and the gear of the cam (eject lock) aligning the mark with the center of the gear (eject lock).
  • Page 24: How To Install The Gear (Mode C)

    HCD-X1V 4-3. HOW TO INSTALL THE GEAR (MODE C) 1 Align the mark on the rotary encoder (S771) with the projection of the assy. 2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
  • Page 25: How To Install The Rotary Encoder (S702), Gear (Stocker Communication)

    HCD-X1V 4-5. HOW TO INSTALL THE ROTARY ENCODER (S702), GEAR (STOCKER COMMUNICATION) 4 gear 5 screw (PTPWH2.6 × 8) (stocker communication) 3 screw 7 two screws (PWH2 × 6) (PTPWH2.6 × 8) 1 rotary encoder Engage the rotary encoder (S702)
  • Page 26: How To Install The Stocker Assy

    HCD-X1V 4-7. HOW TO INSTALL THE STOCKER ASSY 1 Fit three shafts of the stocker assy in respective slits of the cams (stocker U/D). Note: For the location of slits of the cams (stocker U/D), cam (stocker U/D) see 4-6. HOW TO INSTALL CAM (STOCKER U/D).
  • Page 27: Phase Adjustment Between Pinions (Slider) And Slider-1 To 5 (L/R)

    HCD-X1V 4-8. PHASE ADJUSTMENT BETWEEN PINIONS (SLIDER) AND SLIDER-1 TO 5 (L/R) 1 As shown in the following figure, adjust the portion A of each slider to the boss with the slider-1 to 5 (L) and the slider-1 to 5 (R) pushed in the arrow directions respectively (see Fig. 1).
  • Page 28: Test Mode

    HCD-X1V SECTION 5 TEST MODE 6. Each time the [VOLUME +] button is pressed, the display AM STEP CHANGE (US and Canadian models) changes from destination information, MC version, GC The step interval of AM channels can be toggled between 9 kHz version, SYS version, DVD version, CDMA version, CDMB and 10 kHz.
  • Page 29 HCD-X1V DVD SECTION Manual Adjust 1. Track Balance Adjust: 1. DVD SERVICE MODE GENERAL DESCRIPTION 2. Track Gain Adjust: This mode let you make diagnosis and adjustment easily by using 3. Focus Balance Adjust: the remote commander and the TV screen. The instructions, 4.
  • Page 30 HCD-X1V 2. You can check the total time when the laser is turned on during To Clear the Laser Hour Press the [ DISPLAY] button on the remote commander and then playback of DVD and CD from the above menu. The maximum press the [CLEAR] button on the remote commander.
  • Page 31: Electrical Check

    HCD-X1V SECTION 6 ELECTRICAL CHECK 5. CHECKING VERSION INFORMATION DVD SECTION To check the version information, please follow the following procedure. RFMON LEVEL CHECK Procedure: Connection : 1. From the top menu of Remocon Diagnosis Menu, select “4. Version Information” by pressing the [4] button on the remote oscilloscope commander.
  • Page 32: Diagrams

    HCD-X1V SECTION 7 DIAGRAMS 7-1. BLOCK DIAGRAM – RF SERVO/VIDEO Section – (Page 34) SPDIF DIGITAL AUDIO BUS SPDIF 225 DVDRFIP ASDATA0 217 VOA/A ASDATA1 218 HDMI BUS VOB/B ASDATA2 219 BUFFER VOC/C (Page 33) IC4501 VOD/D ASDATA4 222 DVDA...
  • Page 33: Block Diagram - Changer/Hdmi Section

    HCD-X1V 7-2. BLOCK DIAGRAM – CHANGER/HDMI Section – ROLLER MOTOR DRIVE CHANGER CONTROLLER1 • SIGNAL PATH IC711 IC621 : AUDIO M781 OUT1 : VIDEO (ROLLER) OUT2 MODE MOTOR DRIVE IC701 OUT1 M771 (MODE) OUT2 STOCKER MOTOR DRIVE IC721 OUT1 M761...
  • Page 34: Block Diagram - Audio Section

    HCD-X1V 7-3. BLOCK DIAGRAM – AUDIO Section – • R-ch is omitted due to same as L-ch. AUDIO SELECTOR A/D CONVERTER • SIGNAL PATH IC350 IC701 J201 : AUDIO LINE AMP 19 AINL IC360 DOUT : TUNER (FM/AM) R-CH 11 X3...
  • Page 35: Block Diagram - Amp Section

    HCD-X1V 7-4. BLOCK DIAGRAM – AMP Section – • SIGNAL PATH D FLIP-FLOP IC706 : AUDIO CN3500 (Page 34) STREAM PROCESSOR DIGITAL POWER AMP IC3010 IC3150 SPEAKER AMP BUS LRCK DATA1 FRONT LCH+ DATA OUTL1 6 PWM_A OUT_A 28 – 30 L.P.F.
  • Page 36: Block Diagram - Panel/Power Supply Section

    HCD-X1V 7-5. BLOCK DIAGRAM – PANEL/POWER SUPPLY Section – T902 A+9V REGULATOR M+13V SUB POWER IC300 TRANSFORMER +12V RECT A+12V, M+12V REGULATOR D941 IC507 FLUORESCENT INDICATOR TUBE DRIVER IC803 RECT M+9V REGULATOR OSC0 D944 IC507 OSC1 C809, R814 FL801 FLUORESCENT...
  • Page 37 HCD-X1V • Note for Printed Wiring Boards and Schematic Diagrams • Circuit Boards Location Note on Printed Wiring Board: Note on Schematic Diagram: TUNER (FM/AM) • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF) •...
  • Page 38: Printed Wiring Board - Dmb12 Board (Side A)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-6. PRINTED WIRING BOARD – DMB12 Board (Side A) – : Uses unleaded solder. OPTICAL PICK-UP • Semiconductor BLOCK KHM-310CAB (Page 51) (Page 50) Location KHM-313CAB MAIN BOARD MAIN BOARD DMB12 BOARD (SIDE A) Ref.
  • Page 39: Printed Wiring Board - Dmb12 Board (Side B)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-7. PRINTED WIRING BOARD – DMB12 Board (Side B) – : Uses unleaded solder. • Semiconductor Location Ref. No. Location C105 DMB12 BOARD (SIDE B) IC107 IC111 IC150 IC702 IC703 IC705...
  • Page 40: Schematic Diagram - Dmb12 Board (1/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. 7-8. SCHEMATIC DIAGRAM – DMB12 Board (1/6) – (1/6) REGO1 R102 R116 Q101-1 CN101 C101 CD ON SWITCH 0.01 Q101-2 +1.8V REGULATOR OSC BUFFER GND(LD)
  • Page 41: Schematic Diagram - Dmb12 Board (2/6)

    HCD-X1V • • See page 81 for IC Pin Function Description. 7-9. SCHEMATIC DIAGRAM – DMB12 Board (2/6) – See page 72 for Waveforms. (2/6) R1120 R1121 R1122 R1123 R1124 R1125 R1102 R192 R189 C163 0.01 FB107 V2REFO V2REFO LDO2...
  • Page 42: Schematic Diagram - Dmb12 Board (3/6)

    HCD-X1V 7-10. SCHEMATIC DIAGRAM – DMB12 Board (3/6) – (3/6) RF+3.3V R223 SW+5V 100k R246 4.7k SW+3.3V REGO1 C209 R221 C211 R225 REG02 0.033 0.033 100k (Page 40) C233 C214 0.0047 0.001 VREFO R232 R234 SW+5V SPFG FCS- C212 R231 SW+3.3V...
  • Page 43: Schematic Diagram - Dmb12 Board (4/6)

    HCD-X1V 7-11. SCHEMATIC DIAGRAM – DMB12 Board (4/6) – (4/6) CN601 MTR_GND MGND FB601 FB605 SW+9V SW+9V SW+3.3V FL602 SW+3.3V DGND C603 (Page 42) SW+5V SW+5V FB603 FB606 (Page 52) C602 FL603 FB604 FB602 SW+9V FL601 FL4501 SW+3.3V R4610 R4619...
  • Page 44: Schematic Diagram - Dmb12 Board (5/6)

    HCD-X1V • See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description. 7-12. SCHEMATIC DIAGRAM – DMB12 Board (5/6) – C717 SW+3.3V (5/6) 0.01 R740 C718 SW+5V 0.01 R734 (Page 40) R736 +1.8V REGULATOR +3.3V REGULATOR...
  • Page 45: Schematic Diagram - Dmb12 Board (6/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description. 7-13. SCHEMATIC DIAGRAM – DMB12 Board (6/6) – (6/6) HDMI CONTROLLER Q701 R784 2SK1399-T1B LEVEL SHIFT...
  • Page 46: Printed Wiring Boards - Changer Section

    HCD-X1V • See page 37 for Circuit Boards Location. 7-14. PRINTED WIRING BOARDS – CHANGER Section – : Uses unleaded solder. MODE MOTOR BOARD SW(1) BOARD S711 S771 (DISC INSERT (8/12cm)) 4 3 G ROTALY ENCODER (ON: When disc insert)
  • Page 47: Schematic Diagram - Changer Section

    HCD-X1V • See page 74 for IC Block Diagrams. 7-15. SCHEMATIC DIAGRAM – CHANGER Section – CN751 CN702 R731 DIODE DIODE D SENSE D SENSE R733 R734 CN701 IC751 3 . 2 RPR-220 R732 D+3.3V DISC INSERT Q731 DETECT SENSOR...
  • Page 48: Printed Wiring Boards - D-Io/Audio In Boards

    HCD-X1V • See page 37 for Circuit Boards Location. 7-16. PRINTED WIRING BOARDS – D-IO/AUDIO IN Boards – : Uses unleaded solder. AUDIO IN BOARD (COMPONENT SIDE) D-IO BOARD (COMPONENT SIDE) C1005 R1000 IC1004 FB1001 C1001 FL1001 C1010 C1007 R1014...
  • Page 49: Schematic Diagram - D-Io Board

    HCD-X1V • See page 74 for IC Block Diagrams. 7-17. SCHEMATIC DIAGRAM – D-IO Board – A_SEL0 C1003 A_SEL1 DGND D3.3V SPDIF-OUT OPTICAL RECEIVER R1015 FL1001 DGND IC1000 DIGITAL AUDIO SELECTOR TORX147L R1001 DIGITAL-IN (Page 53) CN1000 IC1004 OPTICAL TC74HC151AF...
  • Page 50: Printed Wiring Board - Main Board (Component Side)

    HCD-X1V • See page 37 for Circuit Boards Location. : Uses unleaded solder. 7-18. PRINTED WIRING BOARD – MAIN Board (Component Side) – • Semiconductor Location (Page 38) (Page 38) (Page 58) (Page 38) (Page 46) Ref. No. Location DMB12...
  • Page 51: Printed Wiring Board - Main Board (Conductor Side)

    HCD-X1V • See page 37 for Circuit Boards Location. : Uses unleaded solder. 7-19. PRINTED WIRING BOARD – MAIN Board (Conductor Side) – • Semiconductor Location (Page 38) DMB12 Ref. No. Location BOARD CN601 MAIN BOARD (CONDUCTOR SIDE) D502 H-10...
  • Page 52: Schematic Diagram - Main Section (1/6)

    HCD-X1V • See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description. 7-20. SCHEMATIC DIAGRAM – MAIN Section (1/6) – R633 (1/6) IODO OCSW MEN23 ELV-E3 R635 MEN22 ELV-E2 MEN21 ELV-E1 (Page 53) MEN20...
  • Page 53: Schematic Diagram - Main Section (2/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description. 7-21. SCHEMATIC DIAGRAM – MAIN Section (2/6) – (2/6) CN507 D-GND OVERFLOW2 RB601 OVF2 OVERFLOW1 OVF1...
  • Page 54: Schematic Diagram - Main Section (3/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. 7-22. SCHEMATIC DIAGRAM – MAIN Section (3/6) – (3/6) AMP_D1 AMP_D1 AMP_D2 AMP_D2 CN701 AMP_D3 AMP_D3 D FLIP-FLOP D-GND IC706 AMP_LRCKO SN74LVC1G79DCKR AMP_MCKO AMP_MCKO SI_C...
  • Page 55: Schematic Diagram - Main Section (4/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description. 7-23. SCHEMATIC DIAGRAM – MAIN Section (4/6) – (4/6) +1.2V REGULATOR SI-3010KM-TL SW2.6V SW3.3V D-GND DSP_BCK...
  • Page 56: Schematic Diagram - Main Section (5/6)

    HCD-X1V • See page 74 for IC Block Diagrams. 7-24. SCHEMATIC DIAGRAM – MAIN Section (5/6) – (5/6) MIC AMP IC401 NJM4558MTE2 C412 C406 R422 C422 R403 R409 R473 R474 R421 C421 2.2k 3.3k 10 16V (US,CND) R423 R414 C413...
  • Page 57: Schematic Diagram - Main Section (6/6)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. 7-25. SCHEMATIC DIAGRAM – MAIN Section (6/6) – (6/6) V_SEL0 V_SEL1 R205 V_SEL2 VIDEO V_SEL3 (Page 53) J203 VIDEO SELECTOR VIDEO2 C204 IC202 R204 C220...
  • Page 58: Amp Board (Component Side)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-26. PRINTED WIRING BOARD – AMP Board (Component Side) – : Uses unleaded solder. • Semiconductor Location Ref. No. Location D3551 (CHASSIS) D3552 IC3010 AMP BOARD (COMPONENT SIDE) IC3020 Q3551 IC3030...
  • Page 59: Printed Wiring Board - Amp Board (Conductor Side)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-27. PRINTED WIRING BOARD – AMP Board (Conductor Side) – : Uses unleaded solder. • Semiconductor Location (Page 69) Ref. No. Location POWER BOARD AMP BOARD (CONDUCTOR SIDE) CN903 D3111 D3112...
  • Page 60: Schematic Diagram - Amp Board (1/3)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams.. 7-28. SCHEMATIC DIAGRAM – AMP Board (1/3) – (1/3) C3356 IC3350 0.033 DIGITAL POWER AMP CXD9883M C3353 R3060 PVDD_A R3353 GVDD_A C3362 PVDD_A C3363 /OTW...
  • Page 61: Schematic Diagram - Amp Board (2/3)

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. 7-29. SCHEMATIC DIAGRAM – AMP Board (2/3) – (2/3) (Page C3014 C3015 R3055 C3206 IC3200 0.033 DIGITAL POWER AMP CXD9883M C3203 PVDD_A R3203 GVDD_A C3212...
  • Page 62: Schematic Diagram - Amp Board (3/3)

    HCD-X1V 7-30. SCHEMATIC DIAGRAM – AMP Board (3/3) – (3/3) Q3551 2SC3052EF -T1-LEF R3555 PROTECT DETECT R3554 C3555 100k EP3603 C3610 Q3302 Q3372 Q3222 Q3272 C3603 2SA1235TP-1EF 2SA1235TP-1EF 2SA1235TP-1EF 2SA1235TP-1EF OVER LOAD DETECT OVER LOAD DETECT OVER LOAD DETECT OVER LOAD DETECT...
  • Page 63: Schematic Diagram - Key Section

    HCD-X1V • See page 81 for IC Pin Function Description. 7-31. SCHEMATIC DIAGRAM – KEY Section – D811 D812 D813 D814 D815 SML-020MDT SML-020MDT SML-020MDT SML-020MDT SML-020MDT DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 R860 R859 R858...
  • Page 64: Printed Wiring Board - Led Board

    HCD-X1V • See page 37 for Circuit Boards Location. 7-32. PRINTED WIRING BOARD – LED Board – : Uses unleaded solder. LED BOARD (COMPONENT SIDE) R813 R819 R818 (GRN) (GRN) (GRN) (GRN) (GRN) R830 (AMBER) (AMBER) (AMBER) (AMBER) (AMBER) D811...
  • Page 65: Printed Wiring Boards - Key/Power-Sw Boards

    HCD-X1V • See page 37 for Circuit Boards Location. 7-33. PRINTED WIRING BOARDS – KEY/POWER-SW Boards – : Uses unleaded solder. KEY BOARD POWER-SW BOARD (COMPONENT SIDE) (COMPONENT SIDE) FUNCTION – VOLUME (11) 1-870-018- (11) 1-870-017- S801 – 806 POWER-SW BOARD...
  • Page 66: Printed Wiring Board - Display Board

    HCD-X1V • See page 37 for Circuit Boards Location. 7-34. PRINTED WIRING BOARD – DISPLAY Board – : Uses unleaded solder. (Page 50) MAIN BOARD DISPLAY BOARD CN501 (COMPONENT SIDE) CN801 R805 Q802 C814 C815 R875 D817 D818 D819 D803...
  • Page 67: Schematic Diagram - Display Board

    HCD-X1V • See page 72 for Waveforms. • See page 74 for IC Block Diagrams. 7-35. SCHEMATIC DIAGRAM – DISPLAY Board – FL801 FLUORESCENT INDICATOR TUBE REMOTE CONTROL RECEIVER IC801 NJL23H400A CN802 DGND R854 KEY1 R851 KEY0 R861 KEY2 (Page 63)
  • Page 68: Printed Wiring Board - Power Board (Component Side)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-36. PRINTED WIRING BOARD – POWER Board (Component Side) – : Uses unleaded solder. • Semiconductor Location Ref. No. Location D906 D923 D924 D935 (CHASSIS) IC507 POWER BOARD (COMPONENT SIDE) IC507...
  • Page 69: Printed Wiring Board - Power Board (Conductor Side)

    HCD-X1V • See page 37 for Circuit Boards Location. 7-37. PRINTED WIRING BOARD – POWER Board (Conductor Side) – : Uses unleaded solder. • Semiconductor Location Ref. No. Location POWER BOARD (CONDUCTOR SIDE) D901 D903 D905 D907 D908 D909 D913...
  • Page 70: Printed Wiring Board - Lf Board

    HCD-X1V • See page 37 for Circuit Boards Location. 7-38. PRINTED WIRING BOARD – LF Board – : Uses unleaded solder. LF BOARD (COMPONENT SIDE) (CHASSIS) (CHASSIS) 1-870-019- (11) LF BOARD (CONDUCTOR SIDE) POWER BOARD CN906 (Page (AC IN) LINE...
  • Page 71: Schematic Diagram - Power Supply Section

    HCD-X1V • See page 74 for IC Block Diagrams. 7-39. SCHEMATIC DIAGRAM – POWER SUPPLY Section – ∗ C905 F901 D901 0.01 400V(US,CND) C938 CN901 CN905 CN906 D5SBA60F01 8A 125V(US,CND) 0.0033 400V(AEP,UK) 330p 125V(US,CND) LF901 D931 T6.3AH 250V(AEP,UK) TH901 ∗...
  • Page 72 HCD-X1V • Waveforms – DMB12 Board – – MAIN Board – – AMP Board – IC111 6 IC101 <x/x (YUV5) IC501 qd (XOUT) IC701 3 (LRCLK) IC203 w; (CBOUTB), IC3020 qf (XFSOOUT) (Color bar) wa (CBOUTA) (Color bar) 3.4 Vp-p 3.2 Vp-p...
  • Page 73 HCD-X1V – DISPLAY Board – IC803 tl (OSC1) 3.2 Vp-p 636 ns 1 V/DIV, 200 ns/DIV Q801 (Base) 15.2 Vp-p 6.8 µ s 5 V/DIV, 2 µ s/DIV...
  • Page 74 HCD-X1V • IC Block Diagrams – DMB12 Board – – RELAY Board – IC105, 107, 703 TK11133CSCL-G IC701, 711, 721 BA6956AN IC702 TK11118CSCL-G IC707 TK11150CSCL-G OVER HEAT & CONTROL LOGIC OVER CURRENT PROTECTION CONTROL CIRCUIT BANDGAP REFERENCE – D-IO Board –...
  • Page 75 HCD-X1V IC200, 201, 202 NJM2235V (TE2) IC203 BH7868FS-E2 6MHz VCC1 75Ω VIN 1 32 C OUT BUFFER V OUT SW 1 S-DC OUT 31 S-DC OUT VIN 2 S1/S2 C IN BIAS MUTE1 MUTE1 6MHz BIAS 75Ω CV OUT CV IN...
  • Page 76 HCD-X1V IC504 NJM2887DL3 (TE2) IC701 WM8782SEDS/R MCLK 1 THERMAL PROTECTION DOUT 2 – AINL DIGITAL LRCLK 3 BANDGAP FILTERS CONVERTER AUDIO REFERENCE INTERFACE DGND 4 AINOPL DVDD 5 – BCLK 6 – AINR DIGITAL FILTERS CONVERTER IWL 7 CONTROL FSAMPEN 8...
  • Page 77 HCD-X1V IC706 SN74LVC1G79DCKR – AMP Board – IC3010, 3020, 3030 CXD9876R CLOCK CLOCK GENERATOR GENERATOR 36 XFSIIN (SECONDARY) (PRIMARY) XVSS 35 DVDD VSUBC 34 TEST 33 BFVSS VSSR OUTR2 32 BFVDD VDDR DATA OUTR1 FILTER & SAMPLING LINER GAIN ∆ Σ...
  • Page 78 HCD-X1V IC3050 TK11118CSCL-G OVER HEAT & OVER CURRENT PROTECTION CONTROL CIRCUIT BANDGAP REFERENCE IC3100, 3150, 3200, 3250, 3300, 3350 CXD9883M BST_A PVDD_A Over Current Fault GVDD_A PVDD_A /OTW PVDD_A VREG Gate /HIZ_HS_A Drive PGND /HIZ_LS_A Stuck Detect /RESET PGND Protection...
  • Page 79: Display Board

    HCD-X1V – DISPLAY Board – IC803 ML9208-03MBZ03B 64 VDD 63 DA 8 BIT SHIFT 62 CP REGISTER 61 CS 60 RESET COMMAND PORT DECODER DRIVER CONTROL CIRCUIT DRIVER ADRAM 16W × 2B TIMING TIMING GENERATOR2 GENERATOR1 CGRAM DCRAM 248W × 35B 16W ×...
  • Page 80 HCD-X1V IC901 STR-F6138-LF1352 (US, Canadian models) IC901 STR-F6168-LF1352 (AEP, UK models) CURRENT MIRROR DELAY LATCH DELAY OVER BOTTOM CURRENT PROTECT SKIP LOGIC LOGIC OVER OVER OVER VOLTAGE THERMAL OVER LOAD CURRENT FEED CURRENT PROTECT SHUT DOWN PROTECT PROTECT BACK PROTECT...
  • Page 81 HCD-X1V • IC Pin Function Description DMB12 BOARD IC101 CXD9804R (RF AMP, SERVO DSP, MPEG DECODER) Pin No. Pin Name Description AGND Ground terminal DVDA AC coupled input path A DVDB AC coupled input path B DVDC AC coupled input path C...
  • Page 82 HCD-X1V Pin No. Pin Name Description CD/DVD selection signal output terminal "L": CD, "H": DVD CKSW Chucking detection switch input terminal Not used OCSW Disc table open/close detection switch input terminal Not used EEWP Write protect signal output to the EEPROM DVDD18 Power supply terminal (+1.8V)
  • Page 83 HCD-X1V Pin No. Pin Name Description Two-way data bus with the SD-RAM DVSS Ground terminal 117, 118 RD6, RD5 Two-way data bus with the SD-RAM DVSS Ground terminal 120, 121 RD4, RD3 Two-way data bus with the SD-RAM DVDD18 Power supply terminal (+1.8V)
  • Page 84 HCD-X1V Pin No. Pin Name Description DVDD3 Power supply terminal (+3.3V) MUTE Muting signal output to the motor/coil driver MUTE123 Muting signal output to the motor/coil driver Loading motor drive signal output terminal (forward direction) Not used Loading motor drive signal output terminal (reverse direction) Not used...
  • Page 85 HCD-X1V Pin No. Pin Name Description PLLVSS Ground terminal IDAC Not used PLLVDD3 Power supply terminal (+3.3V) LPFON Data PLL loop filter output terminal LPFIP Data PLL loop filter input terminal LPFIN Data PLL loop filter input terminal LPFOP Data PLL loop filter output terminal VDD3 Power supply terminal (+3.3V)
  • Page 86 HCD-X1V DMB12 BOARD IC701 CXD9873Q (HDMI TRANSMITTER) Pin No. Pin Name Description DVSS Ground terminal (digital system) 2 to 9 C0 to C7 Digital chroma signal input terminal Not used DVDD33 Power supply terminal (+3.3V) (digital system) System clock (27 MHz) signal input from the servo DSP...
  • Page 87 HCD-X1V Pin No. Pin Name Description DAC_AVDD3 Power supply terminal (+3.3V) (analog system) (for D/A converter) AVSS Ground terminal (analog system) (for D/A converter) DAC_AVDD3 Power supply terminal (+3.3V) (analog system) (for D/A converter) Component analog video signal (Y or green) output terminal Not used...
  • Page 88 HCD-X1V DMB12 BOARD IC708 MB95F108ASPFV-GE1-H0601 (HDMI CONTROLLER) Pin No. Pin Name Description AVCC Power supply terminal (+3.3V) Reference voltage (+3.3V) input terminal PE3/INT13 to 3 to 6 Not used PE0/INT10 7 to 10 P83 to P80 Not used P71/TI0, 11, 12...
  • Page 89 HCD-X1V Pin No. Pin Name Description TRAP2 NTSC/PAL selection signal output to the HDMI transmitter Two-way data bus with the HDMI transmitter Serial data transfer clock signal output to the HDMI transmitter AVSS Ground terminal...
  • Page 90 HCD-X1V MAIN BOARD IC2 ADSST-AVR-1115 (DSP) Pin No. Pin Name Description VDDINT Power supply terminal (+1.2V) (for core) Core instruction rate to CLKIN (pin 142) ratio selection signal input terminal CLKCFG0 Fixed at "L" in this set Core instruction rate to CLKIN (pin 142) ratio selection signal input terminal CLKCFG1 Fixed at "H"...
  • Page 91 HCD-X1V Pin No. Pin Name Description 56, 57 A17, A18 Not used Ground terminal VDDEXT Power supply terminal (+3.3V) (for I/0) VDDINT Power supply terminal (+1.2V) (for core) Ground terminal PF_CE Not used SPI_MAS Not used 64, 65 DPSOA, DPSOB...
  • Page 92 HCD-X1V Pin No. Pin Name Description Ground terminal VDDINT Power supply terminal (+1.2V) (for core) Ground terminal VDDINT Power supply terminal (+1.2V) (for core) Ground terminal VDDINT Power supply terminal (+1.2V) (for core) Ground terminal VDDEXT Power supply terminal (+3.3V) (for I/0)
  • Page 93 HCD-X1V MAIN BOARD IC501 M30626MJP-A05FPU0 (SYSTEM CONTROLLER) Pin No. Pin Name Description DAMP_SCDT Serial data output to the stream processor DAMP_SHIFT Shift clock signal output to the stream processor DSP_INTR Interrupt signal input from the DSP SIRCS_IN SIRCS signal input from the remote control receiver...
  • Page 94 HCD-X1V Pin No. Description Pin Name ST_CLK Serial data transfer clock signal output to the tuner (FM/AM) WRITE CE Chip enable signal input terminal (for flash writing) ST_DO Serial data output to the tuner (FM/AM) ST_CE Serial chip enable signal output to the tuner (FM/AM)
  • Page 95 HCD-X1V MAIN BOARD IC621 BH2210FV-E2 (CHANGER CONTROLLER1) Pin No. Pin Name Description CTLIO Input/output selection signal input terminal "L": input, "H": output Fixed at "L" in this set RESET_B Reset signal input from the system controller "L": reset Serial data transfer clock signal input from the system controller...
  • Page 96 HCD-X1V MAIN BOARD IC622 BH2210FV-E2 (CHANGER CONTROLLER2) Pin No. Pin Name Description CTLIO Input/output selection signal input terminal "L": input, "H": output Fixed at "L" in this set RESET_B Reset signal input from the system controller "L": reset Serial data transfer clock signal input from the changer controller1...
  • Page 97 HCD-X1V LED BOARD IC802 BU2099FV (LED DRIVER) Pin No. Pin Name Description Ground terminal Not used DATA Serial data input from the system controller Serial data transfer clock signal input from the system controller Serial data latch pulse signal input from the system controller LED drice signal output of DISC 5 indicator (green) "L": LED on...
  • Page 98: Exploded Views

    HCD-X1V SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark 0 are may have some difference from the original are seldom required for routine service.
  • Page 99: Main Board Section

    HCD-X1V 8-2. MAIN BOARD SECTION not supplied supplied with CN701 not supplied not supplied (D-IO board) (AEP, UK) not supplied M3000 CN701 not supplied POWER board section Note: Refer to the Servicing Notes “NOTE OF HANDLING not supplied THE DMB12 BOARD” (page 5), if replacing the Ref.
  • Page 100: Power Board Section

    HCD-X1V 8-3. POWER BOARD SECTION not supplied not supplied not supplied not supplied DVD mechanism deck section (CDM69EH) not supplied not supplied not supplied F901 not supplied not supplied not supplied not supplied (LF board) not supplied not supplied not supplied Ref.
  • Page 101: Dvd Mechanism Deck Section-1 (Cdm69Eh)

    HCD-X1V 8-4. DVD MECHANISM DECK SECTION-1 (CDM69EH) S702 M761 not supplied (ST ENCODER board) DVD mechanism deck section-2 RELAY board (including ST ENCODER board) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-725-13 STOCKER MOTOR BOARD 4-239-689-01 GEAR (STOCKER DECELERATION) 3-087-053-01 +BVTP2.6 (3CR)
  • Page 102: Dvd Mechanism Deck Section-2 (Cdm69Eh)

    HCD-X1V 8-5. DVD MECHANISM DECK SECTION-2 (CDM69EH) DVD mechanism deck section-3 DVD mechanism deck section-4 optical pick-up section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-727-13 SW (1) BOARD 3-087-053-01 +BVTP2.6 (3CR) 1-686-728-13 SW (2) BOARD 1-686-729-13 SW (3) BOARD 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING...
  • Page 103: Dvd Mechanism Deck Section-3 (Cdm69Eh)

    HCD-X1V 8-6. DVD MECHANISM DECK SECTION-3 (CDM69EH) not supplied not supplied not supplied supplied supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-040-01 SPRING (DISC STOPPER), TORSION 4-240-039-01 LEVER (DISC STOPPER) 4-992-069-01 SCREW (+PTPWH) (M2) (DIA. 7)
  • Page 104: Dvd Mechanism Deck Section-4 (Cdm69Eh)

    HCD-X1V 8-7. DVD MECHANISM DECK SECTION-4 (CDM69EH) not supplied not supplied DVD mechanism deck section-5 M781 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4954-626-1 LEVER (ROLLER) ASSY 3-087-053-01 +BVTP2.6 (3CR) 4-239-666-01 GEAR 4-239-668-01 LEVER (CENTER)
  • Page 105: Dvd Mechanism Deck Section-5 (Cdm69Eh)

    HCD-X1V 8-8. DVD MECHANISM DECK SECTION-5 (CDM69EH) DVD mechanism deck section-6 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-240-020-01 GEAR (TIMING) 4-239-699-01 PULLEY 4-239-708-02 BELT (FRONT), TIMING 4-247-349-02 BELT (ROLLER V) 4-239-697-01 GEAR (CENTER) 4-227-899-31 SCREW (DIA. 12), FLOATING...
  • Page 106: Dvd Mechanism Deck Section-6 (Cdm69Eh)

    HCD-X1V 8-9. DVD MECHANISM DECK SECTION-6 (CDM69EH) M771 not supplied not supplied S771 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-239-693-02 CAM (GEAR) 4-241-731-01 SHUTTER (A), LEVER 1-686-723-13 SENSOR BOARD 4-239-696-01 GEAR (EJECT LOCK) 4-241-732-01 SHUTTER (B), LEVER...
  • Page 107: Optical Pick-Up Section (Khm-310Cab Or Khm-313Cab)

    HCD-X1V 8-10. OPTICAL PICK-UP SECTION (KHM-310CAB or KHM-313CAB) (including sled motor, not supplied spindle motor) (sled motor) not supplied (spindle motor) not supplied Note: Refer to the Servicing Notes “HOW TO IDENTIFY OPTICAL PICK-UP BLOCK” (page 7), if replacing the Ref. No.601.
  • Page 108: Electrical Parts List

    HCD-X1V SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark 0 are parts list may be different from the parts are seldom required for routine service.
  • Page 109 HCD-X1V Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3159 1-112-246-11 ELECT 100uF C3162 1-112-246-11 ELECT 100uF C3275 1-162-964-11 CERAMIC CHIP 0.001uF C3163 1-104-329-11 CERAMIC CHIP 0.1uF C3276 1-163-021-11 CERAMIC CHIP 0.01uF C3277 1-162-964-11 CERAMIC CHIP 0.001uF...
  • Page 110 HCD-X1V Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3801 1-115-339-11 CERAMIC CHIP 0.1uF L3152 1-456-680-11 CHOKE, COIL 10uH C3903 1-107-826-11 CERAMIC CHIP 0.1uF L3171 1-457-077-11 AIR-CORE COIL C3904 1-107-826-11 CERAMIC CHIP 0.1uF L3172 1-457-078-11 AIR-CORE COIL...
  • Page 111 HCD-X1V Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3023 1-216-833-11 METAL CHIP 1/10W R3202 1-216-809-11 METAL CHIP 1/10W R3203 1-216-797-11 METAL CHIP 1/10W R3024 1-216-809-11 METAL CHIP 1/10W R3204 1-216-864-11 SHORT CHIP R3025 1-216-815-11 METAL CHIP...
  • Page 112 < CONNECTOR > < IC > CN801 1-784-871-51 CONNECTOR, FFC (LIF (NON-ZIF)) 19P CN803 1-784-860-51 CONNECTOR, FFC (LIF (NON-ZIF)) 8P IC1000 6-600-466-01 IC TORX147L (SONY) (DIGITAL IN TV OPTICAL) < DIODE > IC1001 6-600-466-01 IC TORX147L (SONY) (DIGITAL IN VIDEO1 OPTICAL) D801...
  • Page 113 HCD-X1V DISPLAY DMB12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D803 8-719-069-56 DIODE UDZSTE-176.2B < TRANSFORMER > D804 8-719-988-61 DIODE 1SS355TE-17 D805 8-719-988-61 DIODE 1SS355TE-17 T801 1-443-757-11 TRANSFORMER, DC-DC CONVERTER ************************************************************ D817 8-719-045-55 LED SEC1201C (FOCUS SUR)
  • Page 114 HCD-X1V DMB12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C158 1-162-970-11 CERAMIC CHIP 0.01uF C160 1-162-970-11 CERAMIC CHIP 0.01uF C712 1-107-826-11 CERAMIC CHIP 0.1uF C161 1-162-970-11 CERAMIC CHIP 0.01uF C713 1-164-172-11 CERAMIC CHIP 0.0056uF 10%...
  • Page 115 HCD-X1V DMB12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FL602 1-233-893-21 FILTER, CHIP EMI FL603 1-234-177-21 FILTER, CHIP EMI R117 1-216-841-11 METAL CHIP 1/10W FL701 1-234-177-21 FILTER, CHIP EMI R118 1-216-801-11 METAL CHIP 1/10W FL703...
  • Page 116 HCD-X1V DMB12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R207 1-216-826-11 METAL CHIP 2.7K 1/10W R208 1-216-839-11 METAL CHIP 1/10W R760 1-216-809-11 METAL CHIP 1/10W R209 1-216-839-11 METAL CHIP 1/10W R762 1-216-864-11 SHORT CHIP R763...
  • Page 117 HCD-X1V DMB12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1177 1-216-809-11 METAL CHIP 1/10W RB108 1-234-400-21 CONDUCTOR, NETWORK (2010X4) R1178 1-216-821-11 METAL CHIP 1/10W RB109 1-234-400-21 CONDUCTOR, NETWORK (2010X4) R1179 1-216-809-11 METAL CHIP 1/10W RB110...
  • Page 118 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < LED > < FUSE HOLDER > D811 8-719-079-89 LED SML-020MDT-T86 (DISC 1) FH901 1-533-313-11 FUSE HOLDER D812 8-719-079-89 LED SML-020MDT-T86 (DISC 2) FH902 1-533-313-11 FUSE HOLDER...
  • Page 119 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-107-826-11 CERAMIC CHIP 0.1uF C306 1-107-826-11 CERAMIC CHIP 0.1uF 1-107-826-11 CERAMIC CHIP 0.1uF C307 1-162-960-11 CERAMIC CHIP 220PF 1-107-826-11 CERAMIC CHIP 0.1uF 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 120 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C519 1-107-826-11 CERAMIC CHIP 0.1uF C723 1-107-826-11 CERAMIC CHIP 0.1uF C520 1-127-715-11 CERAMIC CHIP 0.22uF C724 1-162-917-11 CERAMIC CHIP 15PF C521 1-162-970-11 CERAMIC CHIP 0.01uF C522 1-127-715-11 CERAMIC CHIP 0.22uF...
  • Page 121 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FILTER > < TRANSISTOR > FL501 1-233-893-21 FILTER, CHIP EMI Q301 8-729-027-24 TRANSISTOR DTA114TKA-T146 FL502 1-234-177-21 FILTER, CHIP EMI Q302 8-729-027-24 TRANSISTOR DTA114TKA-T146 FL503 1-234-177-21 FILTER, CHIP EMI...
  • Page 122 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-801-11 METAL CHIP 1/10W 1-216-801-11 METAL CHIP 1/10W R348 1-216-849-11 METAL CHIP 220K 1/10W R200 1-218-285-11 METAL CHIP 1/10W R349 1-216-841-11 METAL CHIP 1/10W R350 1-216-841-11 METAL CHIP...
  • Page 123 HCD-X1V MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R471 1-216-822-11 METAL CHIP 1.2K 1/10W R573 1-216-845-11 METAL CHIP 100K 1/10W R472 1-216-827-11 METAL CHIP 3.3K 1/10W R574 1-216-864-11 SHORT CHIP R473 1-216-825-11 METAL CHIP 2.2K...
  • Page 124 HCD-X1V MAIN MODE MOTOR POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark RB603 1-233-576-11 RES, CHIP NETWORK 100 (3216) R708 1-216-827-11 METAL CHIP 3.3K 1/10W RB621 1-233-576-11 RES, CHIP NETWORK 100 (3216) R709 1-216-833-11 METAL CHIP...
  • Page 125 HCD-X1V POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C919 1-100-566-91 CERAMIC CHIP 0.1uF 0 D907 6-501-193-01 DIODE 1SS355WTE-17 0 C920 1-113-925-11 CERAMIC 0.01uF 250V C921 1-100-566-91 CERAMIC CHIP 0.1uF 0 D908 6-501-193-01 DIODE 1SS355WTE-17...
  • Page 126 HCD-X1V POWER POWER-SW RELAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark (US, CND) A-4731-113-A RELAY BOARD, COMPLETE 0 R912 1-216-363-00 METAL OXIDE 0.33 ********************** (AEP, UK) (Including ST ENCODER BOARD) 0 R914 1-243-665-11 METAL 0.05 <...
  • Page 127 HCD-X1V ROLLER MOTOR ST ENCODER SENSOR STOCKER MOTOR SW (1) SW (2) SW (3) SW (4) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-686-726-13 ROLLER MOTOR BOARD MISCELLANEOUS ******************** ************** 1-833-130-11 WIRE (FLAT TYPE) (8 CORE)
  • Page 128: Revision History

    HCD-X1V REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

Table of Contents