Yamaha E115A Service Manual page 253

I.
Identification...............................................1-5
Ignition and ignition control system ...........8-6
Installing the PCV ....................................5-26
Installing the PTT unit (ET)......................7-31
Installing the clamp bracket (ET) .............7-31
Installing the drive shaft ...........................6-16
Installing the lower unit ............................6-19
Installing the power unit ...........................5-49
Installing the propeller shaft housing .......6-17
Installing the steering arm .......................7-18
Installing the upper case..........................7-19
Installing the water pump and shift rod....6-18
Intake manifold.........................................5-22
L.
Lower unit .........................................3-11, 6-1
Lower unit (115B, 140B models) .............2-12
Lower unit (E115A models) .......................2-7
Lubricating the outboard motor................3-14
Lubricating the throttle gear.......................7-4
M.
Maintenance interval chart ........................3-1
Maintenance specification .........................2-5
Manual format ............................................1-1
Measuring the forward and reverse gear
backlash.................................................6-26
Measuring the peak voltage ......................8-1
P.
PTT electrical system ..............................7-57
PTT motor................................................7-38
PTT unit ...................................................7-34
Parts, lubricant, and sealant ......................1-3
Port view ....................................................8-2
Power unit...........................................3-3, 5-1
Power unit (115B, 140B models) .............2-10
Power unit (E115A models) .......................2-5
Predelivery check ....................................1-12
Propeller selection ...................................1-11
Propeller shaft housing ..............................6-6
Propeller size ...........................................1-11
R.
Removing the PTT unit (ET)....................7-30
Removing the clamp bracket (ET) ...........7-30
Removing the clamp bracket
(MH, WH, E) ..........................................7-24
Removing the crankcase .........................5-34
Removing the cylinder head ....................5-29
Removing the drive shaft .........................6-13
61U5H11
Removing the electrical component ........5-20
Removing the exhaust cover ...................5-26
Removing the flywheel magnet ...............5-19
Removing the intake manifold .................5-24
Removing the lower unit ............................6-4
Removing the piston, connecting rod
assembly and crankshaft assembly.......5-35
Removing the power unit .........................5-17
Removing the propeller shaft housing
assembly..................................................6-8
Removing the starter motor pinion ..........8-14
Removing the steering arm .....................7-17
Removing the water pump and shift rod....6-5
S.
Safety while working ..................................1-3
Selecting the forward gear shim ..............6-24
Selecting the pinion shim.........................6-23
Selecting the reverse gear shim ..............6-25
Selection ..................................................1-11
Self-protection............................................1-3
Serial number ............................................1-5
Shimming........................................6-22, 6-23
Special service tool....................................1-6
Specified torque.......................................2-19
Starboard view ...........................................8-3
Starter motor (WH, E, ET) .......................8-12
Starting system ..........................................8-9
Symbol .......................................................1-2
Synchronizing the carburetor.....................3-5
T.
Test run ....................................................1-16
Tightening torque.....................................2-19
Tiller handle ...............................................7-1
Tilt cylinder and trim cylinder ...................7-48
Top cowling ................................................3-2
Top view .....................................................8-5
Troubleshooting the PTT unit.....................9-6
Troubleshooting the lower unit ...................9-7
Troubleshooting the power unit..................9-1
U.
Upper case, steering arm ..........................7-8
V.
Ventilation ..................................................1-3
1
2
3
4
5
6
7
8
9
i-3