Disassembly - JVC LT-37M60BU Service Manual

www.freeservicemanuals.info
3.1 DISASSEMBLY PROCEDURE
CAUTION AT DISASSEMBLY:
• Be sure to perform the SYSTEM SETTEING, at the end of the procedure.
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers)
makes service procedure manageable.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
3.1.1 REMOVING THE STAND (Fig.1)
(1) Remove the 2 screw [A], then remove the STAND
COVER.
(2) Remove the 4 screws [B], then remove the STAND.
3.1.2 REMOVING THE REAR COVER (Fig.1)
• Remove the STAND.
(1) Remove the JACK COVER (L/R).
(2) Remove the 10 screws [C], the 3 screws [D], and the 2
screws [E].
(3) Remove the REAR COVER.
3.1.3 REMOVING THE REGULATOR PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 4 screws [F], then remove the FAN
BRACKET.
(2) Remove the 1 screw [G], then remove the POWER CORD
HOLDER.
(3) Remove the POWER CORD from the POWER PWB.
(4) Remove the REGULATOR PWB.
3.1.4 REMOVING THE POWER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
(1) Remove the 4 screw [H], then remove the POWER PWB.
3.1.5 REMOVING THE PANEL I/F PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
(1) Remove the 4 screws [J], then remove the PANEL I/F
PWB.
3.1.6 REMOVING THE ANALOG SYGNAL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
(1) Remove the 3 screws [K], then remove the TERMINAL
BASE.
(2) Remove the 4 screws [L], then remove the PANEL I/F
PWB BRACKET.
(3) Remove the 3 screws [M] and 2screw [N], then remove the
ANALOG SIGNAL PWB.
SECTION 3

DISASSEMBLY

3.1.7 REMOVING THE FRONT CONTROL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 3 screws [P], then remove the CONTROL
ASSY with the FRONT CONTROL PWB.
(2) Remove the FRONT CONTROL PWB.
3.1.8 REMOVING THE RECEIVER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 3 screws [Q] and the 1 screw [R], then remove
the TUNER BASE.
(2) Remove the 4 screws [S], then remove the RECEIVER PWB.
3.1.9 REMOVING THE CONNECTOR PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the TOP SHIELD CASE.
(1) Remove the 4 screws [T], then remove the RECEIVER
PWB BRACKET.
(2) Remove the 1 screw [U], then remove the CONNECTOR PWB.
3.1.10 REMOVING THE DIGITAL SIGNAL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the TUNER BASE.
(1) Remove the 7 screws [V] and the 3 screws [W], then
remove the SHIELD COVER.
(2) Remove the 5 screws [X], then remove the DIGITAL
BRACKET.
(3) Remove the DIGITAL SIGNALPWB.
CAUTION :
Make sure to perform the "SYSTEM SETTEING" according to
before page, when DIGITAL SIGNAL PWB is replaced.
Digitized in Heiloo Netherland
4/19/2017
(No.YA360)1-11