Mitsubishi Electric MELSEC iQ-F FX5 User Manual page 116

Address: CH
Decimal
(hexadecimal)
165(A5H) CH3
166(A6H) CH3
167(A7H) CH3
168(A8H) CH4
169(A9H) CH4
170(AAH) CH4
171(ABH) CH4
172(ACH) CH4
173(ADH) CH4
174(AEH) CH4
175(AFH) CH4
176(B0H) CH4
177(B1H) CH4
178(B2H) CH4
179(B3H) CH4
180(B4H) CH4
181(B5H) CH4
182(B6H) CH4
183(B7H) CH4
184(B8H) CH4
185(B9H) CH4
186(BAH) CH4
187(BBH) CH4
188(BBH) CH4
189(BCH) CH4
190(BEH) CH4
191(BFH) CH4
192(C0H) CH4
193(C1H) CH4
194(C2H) CH4
195(C3H) CH4
APPX
114
Appendix 4 Buffer Memory Areas
Setting detail
Standard PID Heating/cooling
control PID control
External output range lower limit
Transistor output functions selection
Startup tuning implementation command
Set value (SV) setting
Alert 1 set value
Alert 2 set value
Alert 3 set value
Alert 4 set value
Heater disconnection alert setting
AUTO/MAN mode System area
switching
Manual output settings System area
AT (auto tuning) implementation command
Operation mode setting
Proportional band (P) Heating proportional
setting band (P) setting
System area Cooling proportional
band setting
Integral time (I) setting
Differential time (D) setting
Control response parameter
System area Overlap/dead band
Upper limit output Heating upper limit
limiter output limiter
Lower limit output System area
limiter
System area Cooling upper limit
output limiter
Output change ratio System area
limiter
Sensor correction value setting
Controller sensitivity (dead band) setting
Control output cycle Heating control output
setting cycle setting
System area Cooling control output
cycle setting
Primary delay digital filter setting
Setting variation rate limiter
AT bias
Normal Operation/ System area
Reverse Operation
Setting
Monitor/Settings/ Default
Selection range value
(Upper and lower limit reverse 0
operation disabled)
Page 161 0
0: Disabled 0
1: Enabled
Within setting limiter range 0
Depends on alert mode and 0
input type
Depends on alert mode and 0
input type
Depends on alert mode and 0
input type
Depends on alert mode and 0
input type
0 to 1000 (0.0 to 100.0 A) (0: 0
Heater disconnection
detection function OFF)
0: AUTO 0
1: MAN
-50 to +1050 -50/0
0: Stop AT 0
1: Implement AT
0: Not used 3
1: Monitor only
2: Monitor + alert
3: Monitor + alert + control
0 to 10000 (0.1 to 1000.0% 30
span)
Set 0 to use position 2
controls.
1 to 10000 (0.1 to 1000.0% 30
span)
0 to 3600 s 240
0 to 3600 s 60
0: Slow 0
1: Regular
2: Fast
-100 to +100 0
Lower limit output limiter +1 to 1000
1050/0 to 1050
-50 to upper limit output limiter 0
-1

0
0 to 1000 0
-5000 to +5000 0
0 to 100 10
5 to 1000 (0.5 to 100.0s) 300
5 to 1000 (0.5 to 100.0s) 0/300
0 to 100 s (0: Function OFF) 0
0 to 1000 0
±Input span [, , digit]
0
0: Normal Operation 1/0
1: Reverse Operation
Data type Backup

Setting
Setting 

Setting

Control

Control

Control

Control
Control 

Control
Setting 

Setting

Normal
Setting 

Control
Control 

Control

Control

Setting

Setting

Setting
Setting 

Setting

Setting

Setting

Setting

Setting
Setting 

Setting

Setting

Setting
Setting 