COLOR TELEVISION RECEIVER Chassis : S64A(P)_Unlimited Model : WS32Z419D8XXEU SERVICE Manual COLOR TELEVISION RECEIVER FEATURES Slimfit(Low Depth) CRT ■ ■ ■ Built In D-TV(IDTV) DVB-T Broadcasting Receiver ■ ■ ■ Flash Download OTA(Over The Air) D-TV S/W Upgrade ■ ■ ■...
Provides S-IF Analog audio And Digital audio signal input and decoding functions. I2C-Comunication,Master Control Micom, Unit(ROM), Flash Down Load. - CXA2165 : H-out,VD-P,VD-N,RGB output,Video and Deflection Signal Processing. - MST3383M : HDMI decoding Functions - STi5517 : CPU of Digital Block.DEMUX, MPEG Decoder Samsung Electronics...
※ Options - 1 Component(480i/480p/576i/576p/720p/1080i 50Hz/60Hz) 1 HDMI(480p/576p/720p/1080i 50Hz,60Hz) ■ Remocon : TM86 ■ Power Supply - Europe(230V), CIS(160V- 300V) ■ Power Supply and Power Comsumption - Input : AC 230V - Max Power : 180W / Stand by : Less than 3W Samsung Electronics...
S-Video Side : 1 Side : 1 Side : 1 Y/Pb/Pr Rear : 1 Ports HDMI Rear : 1 Digital Audio Out Video Out Rear : 1 Rear : 1 Rear : 1 Audio Out Rear : 1 Samsung Electronics...
4. When replacing the CRT Ass'y : No adjustments required. 5. When replacing the front panel master power switch : No adjustments required. 6. When replacing the Side AV : No adjustments required. 7. When replacing the control switch : No adjustments required. Samsung Electronics...
Option(XX XX XX) YC Delay EEPROM Checksum(XXXX) Reset T_ULTPEU_XXXX XX-XX-XX 3. Functions of the Keys within Service Mode MENU Show all menus Move the cursor to select an item. ▲ / ▼ Adjust the selected configuration value ◀ / ▶ Samsung Electronics...
Adjust H Shift Adjust V Linearity Adjust Upper Linearity Lower Linearity V SC H Parabola Adjust Upper Corner Adjust Lower Corner Adjust H Trapezium Adjust Adjust Angle Adjust V Position ※ Input NTSC signal.Then, can control this articles. Samsung Electronics...
Page 13
V Amp Adjust V Shift Adjust H EW Adjust H Shift Adjust V Linearity Adjust Upper Linearity Lower Linearity V SC H Parabola Adjust Upper Corner Adjust Lower Corner Adjust H Trapezium Adjust Adjust Angle Adjust V Position Samsung Electronics...
Page 14
V Amp Adjust V Shift Adjust H EW Adjust H Shift Adjust V Linearity Adjust Upper Linearity Lower Linearity V SC H Parabola Adjust Upper Corner Adjust Lower Corner Adjust H Trapezium Adjust Adjust Angle Adjust V Position Samsung Electronics...
Page 15
G CutOff B CutOff Adjust R Drive Adjust G Drive B Drive Adjust Sub Bright Adjust Sub Contrast Adjust Bright VCTP Contrast VCTP SAT-VCTP Tint VCTP SC_RGB_BRTADJ SC_RGB_CONADJ RGB U_Sat RGB V_Sat RGB24_BRTADJ RGB24_CONADJ RGB24_ USATADJ RGB24_ VSATADJ Samsung Electronics...
Page 16
Lmix offset Peak Center Freq Peaking Coring CTI BW CTI LP CTI Gain CTI Coring V Peaking V Peak Coring gain V Peak high gain V Peak coring high IF Comp Filter DHYAPRESC DHCAPRESC Nega Peaking DCE Gain CORBP Samsung Electronics...
Page 26
R drive offset Cool 1 B drive offset Cool 1 R cutoff offset Cool 1 B cutoff offset Cool 1 R drive offset Cool 2 B drive offset Cool 2 R cutoff offset Cool 2 B cutoff offset Cool 2 3-18 Samsung Electronics...
Page 27
Lmix gain_AV Lmix offset_AV LTI Gain SD Peak_f0_SD Peak_cor_SD CTI_gain_SD Lmix gain_SD Lmix offset_SD LTI Gain HD Peak_f0_ HD Peak_cor_ HD CTI_gain_ HD Lmix gain_ HD Lmix offset_ HD ※ Convert by DTV mode.then,can control this article. Samsung Electronics 3-19...
Page 29
Left Blanking (480) Right Blanking (480) Left Blanking (720) Right Blanking (720) Left Blanking (1080) Right Blanking (1080) RGB Tint DVD Tint Bypass Deint SLMCSW DCE Gain TTX V-Position TTX H-Position PIP CONT PIP-Bright PIP-SCURVE PIP-CTI PIP-Sharp PIP-Tint Samsung Electronics 3-21...
Page 30
R drive offset 1080P G drive offset 1080P R cutoff offset 1080P G cutoff offset 1080P R drive offset 1080i G drive offset 1080i R cutoff offset 1080i G cutoff offset 1080i R drive offset 720P-60HZ G drive offset 720P-60HZ 3-22 Samsung Electronics...
Page 32
High DEV OFF/ON OFF/ON Time Sync OFF/ON OFF/ON Txt Group West EU West EU OSD Language ENGLISH / CIS ENGLISH ENGLISH Digital NR OFF/ON Carrier Mute OFF/ON Search-LNA OFF/ON HDMI OFF/ON WSS Wide Fix OFF/ON Blue Screen OFF/ON 3-24 Samsung Electronics...
② Press "Info → Menu → Mute → Power On" using the remote control and enter Factory Mode. ③ Enter Deflection Mode. ④ Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4. Samsung Electronics 3-25...
Page 34
⑦ When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. 3-26 Samsung Electronics...
6. Slowly turn the Dynamic Focus VR clockwise so that the 2nd line is the most clearly displayed. 7. Check the entire screen focus and repeat steps 3 to 6, if necessary. Samsung Electronics 3-27...
Page 36
5. Adjust the Screen VR of FEB so that the highest point of the Pedestal Level is 175V. ※ Screen Voltage Measurement Data Item Data Required Adjustment The Highest Voltage among RK, GK and Screen Voltage Screen Voltage BK 190Vp-p-3V 3-28 Samsung Electronics...
Page 37
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. Samsung Electronics 3-29...
2) Check that the Master Switch has been pressed. 3) Check that the transmitter is turned on. 4) Check that transmitter device selection is set to TV. 5) Check that the signal cable is properly connected. 6) Check that channel setting has been set. Samsung Electronics...
Page 69
When the screen is not properly displayed and the left or right side of the picture is shrunk, or the top or bottom of the screen is expanded or shrunk, check if the Deflection Board is out of order. Samsung Electronics...
Page 70
Power Board and the Def lection Board properly connected? Replace the Is a CRT high voltage been measured? Main Board Is the cable f rom the Connect the cable Main Board to t he CRT Ass' y properly connected? Samsung Electronics...
Cannot select an A/V channel. out, you cannot select an A/V channel. Check if the connector is properly connected. Cannot select a menu. Check if the menu is grayed out. If a menu is grayed out, it cannot be selected. Samsung Electronics...
Page 72
■ Set the auto volume control to ON. There is a lot of noise. Keep the antenna away from the power cord or connectors if possible. The selected language does not Press the Multiplex button to select the TV. appear. Samsung Electronics...
Page 73
This noise may occur when the plastic material inside the TV expands or contracts according The TV makes a noise as if to the seasonal temperature or humidity. This is like the noise from a furniture/cabinet/sink something is dropping inside. unit, and there is no need for concern. Samsung Electronics...
Therefore, you can determine whether the software has been properly downloaded, if you know the correct checksum for that version of the software. You can check the checksum according in the following order. Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 0xab2b) ■ Checksum Examples T_ULTPEU_1002 : Checksum = 0x4faa Samsung Electronics...
OK or Low L804 Open R817 Line Change Change 12V Line HC401 H-OUT TR Cehck Materials B+ check Check Materials F-Box Check IC801S and Change the Module B+(132V) Line F/BACK LINE CHECK Change No-Power PC801S/DZ801/Q803... Materials Repair End Samsung Electronics...
If no signal is received even though the RF signal from the external aerial is connected to the MAIN Board Tuner, check the following items. - Supply Power: 5V, 3.3V, 33V - Check for an RF defect: Check the CVBS output - Check for an AUDIO defect: Check the SiF Signal output 6-12 Samsung Electronics...
Page 80
It receives the EXT1/EXT2/signal and consists of monitor output (video and audio). The signal is input to VSP9402 through the port. If no signal input/output is detected, check the following items. - Power supply : VSP9402(3.3V,1.8V) , CXA2180(5V) - Check if the input and output jacks are defective. Samsung Electronics 6-13...
Page 81
The signal is received from the Audio Processor (VCT69xyP) and sound is output at 10W + 10W power. - Power supply :15V - Check for input defects : L/R - Check for output defects : L+, L-, R+, R- 6-14 Samsung Electronics...
Page 82
It processes the one chip that Micom, Switching, Decoder - Power supply : 8V, 5V, 3.3V, 1.8V - Check for input defects : RF, SCL, SDA, S-Video(Y,C), SIF, Scart 1/2, Component 1/2, HDMI - Check for output defects : RF, Monitor out, R/G/B Sound L/R Samsung Electronics 6-15...
Page 83
R/G/B. It also outputs the V/H Drive, E/W and performs the ABL and EHT operation. If V-Drive output is not detected, check for an IC defect. - Power supply : 5V, 9V - Check for input defects : R/G/B, H/V - Check for output defects : 6-16 Samsung Electronics...
Page 89
S- MUTE2 Fr om M icom #49 COMP1 I N - L 4052 COMP1 I N SCLK HDMI I N - L #121 LRCLK #122 HDMI I N - R DATA 3383M #120 7-2-3 CRT Diagram t l i Samsung Electronics...
*GT804 : This is a ground port to prevent high voltage due to lighting. *CN802 : This is a 3 pin port connected to the AC power cable. It is connected to the power cable socket. *GT805, GT806 : This is a port connected to the D-Coil surrounding the CRT. Samsung Electronics...
Page 95
PCB Diagram 9-1-3 Main Board Connector Pin CN401 CN601 Connected to the CRT Board Connected to the Speaker Port PIN No. Pin Name PIN No. Pin Name 200V Heater -16.5V +16.5V Samsung Electronics...
* CN05 : This is a 4 pin port connected to the Control Ass'y, and receives TV/Video, Menu, Ch Up/Down and Vol -/+ signals. * CN03 : This is a 8 pin port connected to the Side AV, and receives S-Video2 and AV4 external inputs. Samsung Electronics...
Page 97
Connected to the CRT Ass'y Connected to the Control Ass'y Connected to the Side AV Port PIN No. Pin Name PIN No. Pin Name PIN No. Pin Name SV-C-IN KEY-1 SV-C-ID F-CVBS IN B-OUT KEY-2 FAV-L-IN G-OUT FAV-R-IN R-OUT 12V_A POWER TILT Samsung Electronics...
* CNC02 : This is a port that receives power for the CRT and AMP from the Main Board. * FV1 : A port to connect the VM signal to the DY Ass'y. * FN1 : A port to connect signals to the Tilt Coil and is regured for the screen slant adjustment. Samsung Electronics...
Page 99
PIN No. Pin Name 200V B-OUT Heater G-OUT -16.5V +16.5V R-OUT 12V_A POWER TILT Connected the VM signal to the DY Ass'y Connects the signal to the Tilt Coil PIN No. Pin Name PIN No. Pin Name TILT TILT Samsung Electronics...
Schematic Diagram 10. Schematic Diagram 10-1 MAIN 10-1-1 POWER & DEF This Document can not be used without Samsung’s authorization. TP03 TP02 TP01 Power Signal TP04 TP05 TP06 TP08 TP07 Samsung Electronics 10-1...
Page 101
Schematic Diagram 10-1-2 Tuner This Document can not be used without Samsung’s authorization. Power Signal TP13 TP14 TP12 TP15 TP16 TP17 TP09 TP10 TP19 TP18 TP11 10-2 Samsung Electronics...
Schematic Diagram 10-2 Feature Box 10-2-1 Signal Input This Document can not be used without Samsung’s authorization. Power Signal 10-4 Samsung Electronics...
Page 104
Schematic Diagram 10-2-2 VCTP This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-5...
Page 105
Schematic Diagram 10-2-3 HDMI This Document can not be used without Samsung’s authorization. Power Signal 10-6 Samsung Electronics...
Page 106
Schematic Diagram 10-2-4 CXA2165 This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-7...
Press to see an on-screen menu of your TV’ s features. Press the MENU button in DTV mode to display the DTV menu. The analog menu appears when you press the MENU button again. To dismiss the menu, press the MENU button once again. Samsung Electronics 11-1...
Because there are three sets of input jacks, you can connect three different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.) Please insert the card as shown Inserting the CI (Common Interface) card If you want to watch the scrambled channel, insert the CI card into the “COMMON INTERFACE” slot. Cable Television Network 11-2 Samsung Electronics...
Page 112
PCMCIA Slot supports the DVB Common Interface (DVB-CI) standard. This connection is provided for future expansion of your Samsung DTV set allowing the installation of DVB-CI compatible peripherals, for example a DVB-CI module to support pay TV services. The availability of DVB-CI peripherals varies country by country. Please contact your retailer for information about the availability of DVB-CI peripherals in your region.
You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, DVD, Cable box, and Samsung Set-top Boxes.
Notice: Disassemble the product after disconnecting the power cord and discharge the unit to prevent an electric shock and damage to the product due to static electricity. Power ① Remove the power cord fixing the Back Cover Cord Samsung Electronics 12-1...
Page 115
② To separate the power cord, slide the fixing clip and lift the cable up. ① Separate the CRT Ass'y from the CRT ② Separate the TBC wire, GND, VM and Tilt cables from the CRT Ass'y sequentially. 12-2 Samsung Electronics...
Page 116
Notice: Take care when separating the wires because pulling the wires by force may damage the socket. In addition, sepa- rate the wires on a flat and clean surface so as to prevent scratching of the material and the PCB. Samsung Electronics 12-3...
Page 117
② First separate the cable from the Splitter using a tool such as nippers. Notice: Since pulling the wire by force may damage the coating of the wire, separate the wire holding the metal part with the tool. ① Remove the DY Connector from the Main Board. 12-4 Samsung Electronics...
- A circuit for correcting the spool shape which appears on the left and right part of a picture. This is caused by the difference between the distances from the center of a picture to each corner. KA393, FQP630 etc. (Adopt PWM circuit) Samsung Electronics 13-1...
- Consists of L304, C305, C439, R312. Symmetrize the up and down amplitude using the saturable reactor of L304 and adjust Vertical Gain by controlling the capacity value of C305 and C439 If the correction vector is excessive, one can slightly reduce the resistance of R312 Samsung Electronics 13-3...
Page 121
< Ve r t i c a l W ave fo r m < No r m a l Ve r t ical a f t e r co r r e ct i i o n > S i g na l > 13-4 Samsung Electronics...
Page 122
..D415 : moves to the right of a picture ..D417 : moves to the left of a picture Total Length of a Picture Moved (m/m) Condition Left Center Right To Left To Right To Left To Right To Left To Right After Samsung Electronics 13-5...
Page 123
It detects the ABL voltage and inputs to Q401 Gate through R423 resistance. Then the ABL voltage change is sent to IC401(KA393) output and controls the DC of Q404(FQP630) Gate terminal, to keep the picture size from changing. 13-6 Samsung Electronics...
Page 124
COMP capacity value, therefore, should be varied +/- 1step from the factory- adjusted condition, since a gain widely varies dependant on the SET distribution. ▶ Before and After of E/W Circuit Correction Samsung Electronics 13-7...
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. Samsung Electronics 14-1...
Anynet is an AV network system that enables the easy-to-use AV interface for users by controlling connected AV devices Reception Sensitivity Amplification through the Anynet menu when AV devices of Samsung A signal amplification technique that amplifies weak broadcast- Electronics are connected.