Table of Contents
Advertisement
KDC-MP4032
How to enter the test mode
Press and hold the [1] and [3] keys and reset.
(While "– – – –" is being displayed, power can be ON for 30
minutes.)
How to clear the test mode
Reset, momentary power down, Acc OFF, Power OFF, de-
tach the panel.
Test mode default condition
• Source is STANDBY.
• Display lights are all turned on.
• The volume is at -10dB (The display is 30).
• LOUD is OFF.
• CRSC is off regardless of the availability of switching func-
tion.
• SYSTEM Q is NATURAL (=FLAT).
• BEEP should always function when the key is pressed.
Special display in tuner mode
Error is found in front-end, etc. if indications below are dis-
played while in tuner mode.
"TNE2P_NG" : Front-end E2PROM values are still default
(not determined).
"TNCON_NG" : Cannot communicate with the front-end.
K3I forced switching
Every time when [6] key is pressed in tuner FM mode,
switched in the following order: AUTO → Forced WIDE →
Forced MIDDLE → Forced NARROW → AUTO. Default
status is AUTO, and displayed as shown below.
AUTO: FM1_98.1A
Forced WIDE: FM1_98.1W
Forced MIDDLE: FM1_98.1M
Forced NARROW: FM1_98.1N
CD receiver test mode specification
• Display mode default setting shall be P-TIME.
• Jumps to the following tracks by pressing the [
No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →
No. 22 → No. 14 → No. 9 (recursive)
Note that when playing an MP3 / WMA / AAC disc with 8
files or less, the disc is played from the 1st track in the
normal order.
• Pressing the [
] key goes back by 1 track from the track
being played.
• When playing an MP3 / WMA / AAC disc, display the file
format before starting to play each file. ("MP3", "WMA",
"AAC")
10
TEST MODE
• While in CD source, press the [1] key to jump to No. 28.
• While in CD source, press the [2] key to jump to No. 14.
• While in CD source, press the [3] key to display the CD
mechanism model name and the version. Press the [3] key
again to go back to the normal screen. (Time code display)
• When CD is the source, press the [6] key to jump to No. 15.
At this time, the volume value is set to 27 (4V PRE).
AUDIO adjust mode
• Press the [AUD] key and enter the audio adjustment mode.
• Press the remote control [∗] key and [AUD] key to go into
the audio adjustment mode.
• Both AUDIO FUNCTION MODE and SETUP MODE ad-
justment items are included.
• By pressing [AUD] key and then [FM] key, switch the item
to be adjusted in the following order. (Only in forward rota-
tion)
The default item shall be Fader, and then the item is for-
warded in the following order: Balance → Bass Level →
Middle Level → Treble Level → HPF Front → HPF Rear →
LPF Sub Woofer (thereafter arbitrary).
• Continuous forwarding by remote control is prohibited.
• Fader is adjusted by the VOL knob and [
3 steps: R15 ↔ 0 ↔ F15. (Default value: 0)
• Balance is adjusted by the VOL knob and [
in 3 steps: L15 ↔ 0 ↔ R15. (Default value: 0)
• Bass/Middle/Treble Level are adjusted by the VOL knob and
[
] / [
• HPF Front / Rear is adjusted by the VOL knob and [
] keys in 2 steps: Through ↔ 180Hz. (Default value:
[
Through)
• LPF Sub Woofer is adjusted by the VOL knob and [
] keys in 2 steps: 60Hz ↔ Through. (Default value:
[
Through)
• Sub Woofer Phase is adjusted by the VOL knob and [
] key.
] keys in 2 steps: Reverse ↔ Normal. (Default value:
[
Normal)
• Volume Offset is adjusted by the VOL knob and [
keys in 2 steps: -8 ↔ 0. (Default value: 0)
• Loudness ON/OFF is adjusted by the VOL knob and [
] keys in 2 steps: OFF ↔ ON. (Default value: OFF)
[
6 6 8 0 : 0 1 2 3
Model name
Version
] keys in 3 steps: -8 ↔ 0 ↔ +8. (Default value: 0)
] / [
] keys in
] / [
] keys
] /
] /
] /
] / [
]
] /
Advertisement
Table of Contents
