Table of Contents
Advertisement
•
Select the required quantity of water by pressing the
icons (B7) and (B8). The progress bar shows the
quantity of water selected.
•
Press the OK icon (B9) to confirm (or the ESC icon (B6) to
cancel the operation.
•
Press the ESC (B6) icon (B6) twice to exit the menu.
•
The appliance is now reprogrammed with the new settings
and is ready.
MAKING CAPPUCCINO
N.B.: Set the quantity of coffee you want to use to make
the cappuccino in the "Program cappuccino" function in the
menu.
•
Select the taste of the coffee you want to use to make the
cappuccino by pressing the
•
Remove the lid of the milk container.
•
Fill the container with about 100 grams of milk for each
cappuccino to be prepared (fig. 15). Never exceed the MAX
level (corresponding to about 750 ml) marked on the con-
tainer. You should ideally use skimmed or semi-skimmed
milk at refrigerator temperature (about 5°C).
•
Make sure the intake tube is correctly inserted in the rubber
washer (fig. 16) then replace the milk container lid.
•
Position the frothed milk regulator (C1) between the words
CAPPUCCINO and CAFFELATTE printed on the milk container
lid. The quantity of froth can be adjusted by moving the
regulator towards the word CAFFELATTE for a denser froth.
Moving it towards the word CAPPUCCINO obtains a less
dense froth.
NO froth
"Denser" froth
frothed milk regulator
"Less dense" froth
•
Remove the hot water spout and attach the milk container
to the nozzle (fig. 17).
•
Position the milk spout as shown in fig. 18 and then place a
sufficiently large cup under the coffee and milk spouts.
•
Press the
icon (fig. B12). "CAPPUCCINO..." is displayed
and after a few seconds, frothed milk flows out of the milk
spout into the cup below. (La fuoriuscita del latte si inter-
rompe automaticamente). (Delivery stops automatically).
icon (B4).
10
•
The appliance delivers coffee.
•
The cappuccino is now ready. Sweeten to taste and, if de-
sired, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or
coffee can be interrupted by pressing the
NOTE 2: If the milk in the container finishes while delivering
frothed milk, remove the container and add milk. Reattach and
press the
(B12) to request a cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino.
"PRESS CLEAN!" flashes on the display.
•
Place a recipient under the milk spout (fig. 20).
•
Press the CLEAN button on the lid (C3) and hold down for at
least 5 seconds (fig. 20) to start the cleaning function.
The appliance displays the message "CLEANING!" above a
progressive bar.
You should not release the CLEAN button until the bar is
complete indicating that cleaning is concluded.
When the CLEAN button is released, the function stops.
After cleaning, remove the milk container and place in the
refrigerator.
The milk should not be left out of the refrigerator for more
than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk the ap-
pliance delivers automatically into the cup, proceed as described
in the section "Changing the quantity of coffee and milk for cap-
puccino".
CHANGING THE QUANTITY OF COF-
FEE AND MILK FOR CAPPUCCINO
The appliance is set by default to automatically deliver a normal
cappuccino.
To change these quantities, proceed as follows:
Changing the quantity of milk
•
Fill the container with milk up to the maximum level indi-
cated on the container.
•
Press the
icon (B2) to enter the menu, then press the
icons (B7) and (B8) (fig. 2) until "PROGRAM CAP-
PUCCINO" is displayed.
•
Press the OK icon (B9) to confirm. "PROGRAM MILK" is dis-
played.
•
Press the OK icon (B9) again.
•
Select the quantity of milk required by pressing the
icons (B7) and (B8). The progress bar shows the quantity of
EN
icon (B12).
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
