GE L60 Instruction Manual page 155

5 SETTINGS
Table 5–7: L60 FLEXLOGIC™ OPERANDS (Sheet 4 of 7)
OPERAND TYPE OPERAND SYNTAX
ELEMENT: OPEN POLE OP ΦA
OPEN POLE OP ΦB
Open Pole Detector
OPEN POLE OP ΦC
OPEN POLE BKR ΦA OP
OPEN POLE BKR ΦB OP
OPEN POLE BKR ΦC OP
OPEN POLE BLK N
OPEN POLE BLK AB
OPEN POLE BLK BC
OPEN POLE BLK CA
OPEN POLE REM OP ΦA
OPEN POLE REM OP ΦB
OPEN POLE REM OP ΦC
OPEN POLE OP
ELEMENT: PH DIR1 BLK A
Phase Directional PH DIR1 BLK B
Overcurrent PH DIR1 BLK C
PH DIR1 BLK
ELEMENT: PH DIST Z1 PKP
Phase Distance PH DIST Z1 OP
PH DIST Z1 OP AB
PH DIST Z1 OP BC
PH DIST Z1 OP CA
PH DIST Z1 PKP AB
PH DIST Z1 PKP BC
PH DIST Z1 PKP CA
PH DIST Z1 SUPN IAB
PH DIST Z1 SUPN IBC
PH DIST Z1 SUPN ICA
PH DIST Z1 DPO AB
PH DIST Z1 DPO BC
PH DIST Z1 DPO CA
PH DIST Z2 to Z3
ELEMENT: PHASE IOC1 PKP
Phase PHASE IOC1 OP
Instantaneous PHASE IOC1 DPO
Overcurrent PHASE IOC1 PKP A
PHASE IOC1 PKP B
PHASE IOC1 PKP C
PHASE IOC1 OP A
PHASE IOC1 OP B
PHASE IOC1 OP C
PHASE IOC1 DPO A
PHASE IOC1 DPO B
PHASE IOC1 DPO C
PHASE IOC2
ELEMENT: PHASE OV1 PKP
Phase Overvoltage PHASE OV1 OP
PHASE OV1 DPO
PHASE OV1 PKP A
PHASE OV1 PKP B
PHASE OV1 PKP C
PHASE OV1 OP A
PHASE OV1 OP B
PHASE OV1 OP C
PHASE OV1 DPO A
PHASE OV1 DPO B
PHASE OV1 DPO C
GE Multilin
OPERAND DESCRIPTION
Open pole condition is detected in phase A
Open pole condition is detected in phase B
Open pole condition is detected in phase C
Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase A
Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase B
Based on the breaker(s) auxiliary contacts, an open pole condition is
detected on phase C
Blocking signal for neutral, ground, and negative-sequence overcurrent
element is established
Blocking signal for the AB phase distance elements is established
Blocking signal for the BC phase distance elements is established
Blocking signal for the CA phase distance elements is established
Remote open pole condition detected in phase A
Remote open pole condition detected in phase B
Remote open pole condition detected in phase C
Open pole detector is operated
Phase A Directional 1 Block
Phase B Directional 1 Block
Phase C Directional 1 Block
Phase Directional 1 Block
Phase Distance Zone 1 has picked up
Phase Distance Zone 1 has operated
Phase Distance Zone 1 phase AB has operated
Phase Distance Zone 1 phase BC has operated
Phase Distance Zone 1 phase CA has operated
Phase Distance Zone 1 phase AB has picked up
Phase Distance Zone 1 phase BC has picked up
Phase Distance Zone 1 phase CA has picked up
Phase Distance Zone 1 phase AB IOC is supervising
Phase Distance Zone 1 phase BC IOC is supervising
Phase Distance Zone 1 phase CA IOC is supervising
Phase Distance Zone 1 phase AB has dropped out
Phase Distance Zone 1 phase BC has dropped out
Phase Distance Zone 1 phase CA has dropped out
Same set of operands as shown for PH DIST Z1
At least one phase of PHASE IOC1 has picked up
At least one phase of PHASE IOC1 has operated
At least one phase of PHASE IOC1 has dropped out
Phase A of PHASE IOC1 has picked up
Phase B of PHASE IOC1 has picked up
Phase C of PHASE IOC1 has picked up
Phase A of PHASE IOC1 has operated
Phase B of PHASE IOC1 has operated
Phase C of PHASE IOC1 has operated
Phase A of PHASE IOC1 has dropped out
Phase B of PHASE IOC1 has dropped out
Phase C of PHASE IOC1 has dropped out
Same set of operands as shown for PHASE IOC1
At least one phase of Overvoltage 1 has picked up
At least one phase of Overvoltage 1 has operated
At least one phase of Overvoltage 1 has dropped out
Phase A of Overvoltage 1 has picked up
Phase B of Overvoltage 1 has picked up
Phase C of Overvoltage 1 has picked up
Phase A of Overvoltage 1 has operated
Phase B of Overvoltage 1 has operated
Phase C of Overvoltage 1 has operated
Phase A of Overvoltage 1 has dropped out
Phase B of Overvoltage 1 has dropped out
Phase C of Overvoltage 1 has dropped out
L60 Line Phase Comparison Relay
5.4 FLEXLOGIC™
5
5-63