Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Philips DVR I Series
Summary of Contents for Philips DVR I Series
-
Page 1: Digital Video Recorders
DVR1 Series Digital Video Recorders Philips Communication, Security & Imaging... -
Page 3: Table Of Contents
1.3.2 Connection of Alarm Contact ...4 Programming the REO System Monitor...5 Programming the DVR1...5 Remote Viewing Considerations ...5 INSTALLATION GUIDE FOR THE COMBINED PHILIPS MULTIPLEXER, INTUIKEY KEYBOARD & DVR1 SERIES SYSTEM ...6 Overview ...6 Required Software Version ...6 Installation ...6 DVR1 Keyboard Menus ...7... -
Page 4: Reo Quick Install Guide
REO QUICK INSTALL GUIDE Introduction This guide provides the steps necessary to install the DVR1 in combination with a REO Multiplexer or REO Switcher Monitor. If you are not familiar with the operations of the DVR1 and the REO Monitor, refer to the corresponding instruction manuals. Required Software Version Ensure that the DVR1 and REO monitor’s software version is equal to or higher than noted below. -
Page 5: Programming The Reo System Monitor
• For a DVR1 connected directly to a Hub, use a Straight Through cable. • For a DVR1 connected directly to a PC, use a Crossover cable. • For a DVR1 connected via standard phone line (POTS) using LAN modems, refer to the Philips CSI Web site. A PSTN-LAN modem can be used for remote access to one of the Philips digital products through a POTS line. -
Page 6: Installation Guide For The Combined Philips Multiplexer, Intuikey Keyboard & Dvr1 Series System
This new software simplifies retrieval of the DVR1’s recorded video via the IntuiKey keyboard. Required Software Version Ensure that the keyboard, DVR1, and Philips Multiplexer software versions are equal to or higher than those noted below. Software for these products is available at www.philipscsi.com. -
Page 7: Dvr1 Keyboard Menus
DVR1 Keyboard Menus There are two new keyboard menus that provide direct access to the DVR1 menus and its recorded video (refer to the keyboard’s instruction manual for further information on keyboard menus). DVR1 Controls 2.4.1 DVR1 Controls Menu To view the DVR1 CONTROLS menu, at the Keyboard’s MULTIPLEXER MAIN MENU, select RECORDER CONTROLS, then DVR1 CONTROLS. -
Page 8: Dvr1 Playback Conrols Menu
2.4.2 DVR1 Playback Controls Menu Below is a list of the new Keyboard Softkey buttons for the DVR1 Playback Controls menu along with an explanation of the functions they perform. Softkey Exit Full, Quad, Multi Pause, Play Forward, Play Reverse, Frame Advance, Frame Reverse, Fast Reverse, Fast Forward, Increase Speed, Decrease Speed... -
Page 9: Rs-232 Remote Protocol
RS-232 REMOTE PROTOCOL Supported Command Sequences The DVR1 supports the following command sequences, entered via PC once communication has been established between the PC and the DVR1. The Baud Rate should be set at 9600 Baud, with 1 Stop Bit, 8 Data Bits, and Parity at None. All byte values entered at the PC must be in hexadecimal values. - Page 10 SET CLOCK Example: In this example, 14:39 on December 25, 2000 is used to demonstrate the Set Clock Command String. Notation Used in Value Column Year Character #1 Year Character #2 Month Character #1 Month Character #2 Day Character #1 Day Character #2 Hour Character #1 Hour Character #2...
- Page 12 3935 890 41811 02-18 © 2002 by Philips Electronics N.V. © 2002 by Philips Communication, Security & Imaging, Inc. All Rights Reserved. Philips ® is a registered trademark of Philips Electronics N. A. Corp. Data subject to change without notice...