Specifications; General Safety Rules - Makita 3708 Instruction Manual

ENGLISH
1 Loosen
2 Tighten
3 Hold
4 Wing nut
5 Spring washer
6 Flat washer (small)
7 Base
8 Flat washer (large)
9 Bolt
10 Trimmer shoe
11 Adjusting roller
12 Scale
13 Bit protrusion
14 Lever
15 Graduation
16 Wing bolt
17 Amount of chamfering
18 Switch lever
19 Workpiece

SPECIFICATIONS

Model
Collet capacity .................................................................................... 6 mm or 1/4"
-1
No load speed (min ) ......................................................................... 35,000
Overall length...................................................................................... 308 mm
Net weight........................................................................................... 1.3 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS.
Work area safety
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
Explanation of general view
20 Feed direction
21 Bit revolving direction
22 (View from the top of the tool)
23 Correct bit feed direction
24 Trimmer shoe, straight guide
or trimmer guide
25 Bolt
26 Guide plate
27 Straight guide
28 Flat washer
29 Wave washer
30 Wing nut
31 Clamp screw (A)
32 Centre hole
33 Nail
34 Adjusting screw
35 Clamp screw (B)
36 Trimmer guide
37 Bit
2.
3.
Electrical safety
4.
5.
6.
GEA001-3
7.
8.
38 Guide roller
39 Screws
40 Screwdriver
41 Templet guide
42 Convex portions
43 Straight bit
44 Templet
45 Distance (X)
46 Not available
47 Not available
48 Not available
49 Not available
50 Not available
51 Not available
52 Not available
53 Not available
54 Not available
55 Limit mark
56 Brush holder cap
3708/3708F
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
3708FC
6 mm or 1/4"
26,000
308 mm
1.3 kg
7