Philips MCD802/12 Quick Start Manual

Welcome to Philips! What's in the box
Micro DVD Theater
Register your product and get support at
www.philips.com/welcome
MCD802
Remote control
Power cord
1
Quick start guide
Install remote control batteries
A
1
Connect
2
Setup
3
Enjoy
Connect control cable
B
EN
1
Connect
Connect speakers
C
Composite video Control cable
cable (yellow)
Right speaker
XXXXXXX
XXXXXX XXXXXX
Quick start guide
1
Connect
2 Setup
2 Enjoy
Eng
FM wire antenna Quick start guide User manual
Connect
Connect FM antenna
D
1
Open the battery compartment.
2
Insert 2 AAA batteries with correct
polarity (+/-) as indicated.
3
Close the battery compartment.
Connect TV
E
1
Connect the supplied control cable to the
CONTROL CABLE jacks on the main unit.
1
Connect
Connect power
F
D Note
• Ensure that the colors of the speaker
wires and terminals are matched.
Left speaker
1
Hold down the socket fl ap.
2
Insert the stripped part of the wire com-
pletely.
• Insert the right speaker wires to
" SPEAKER RIGHT ", left speaker wires
to " SPEAKER LEFT ".
3
Release the socket fl ap.
1
Connect the supplied FM wire antenna to
C Caution
• Risk of product damage! Ensure that the
the FM ANTENNA socket on the unit.
power supply voltage corresponds to
the voltage printed on the back or the
underside of the unit.
• Risk of electric shock! When you unplug
the AC power cord, always pull the plug
from the socket. Never pull the cord.
• Before connecting the AC power cord,
ensure you have completed all other
connections.
1
Connect the supplied composite video
cable to:
TV • the VIDEO socket on this unit.
• the video input socket on the TV.
2
Setup
A Set the clock
1
In standby mode, press CLOCK to activate
1
Connect the power cord to the AC the clock setting mode.
MAINS~ jack on the main unit.
The time digits are displayed and begin to blink.
»
2
Connect the power plug to the wall outlet. If the time digits are not displayed, press
»
and hold for more than 2 seconds to
switch to standby mode, then repeat step 1.
2
Press / to set the hour.
3
Press / to set the minute.
4
Press and hold CLOCK to select 12-hour
or 24-hour format.
5
P ress CLOCK to confi rm .
3
Enjoy
E Tip
• See the User Manual for how to connect
other devices to this system.
A
Play disc
1
Press DISC to select the disc source.
2
Press to open the disc compartment.
3
Insert a disc with the printed side facing
up, then close the disc compartment.
Play starts automatically.
»
• To pause/resume play, press .
• To stop play, press 9 .
B
Play from USB
1
Flip open the USB socket cover on the
front panel.
2
Insert the USB plug of a USB device into
the USB socket.
3
Press USB to select the USB source.
Play starts automatically.
»
• To pause/resume play, press .
• To stop play, press 9 .
3
Enjoy
Program and tune to radio
C
stations
E Tip
• For optimal reception, fully extend and adjust
the position of the FM antenna.
First time tuning
When you access to radio mode for the fi rst
time, follow the instructions to install the radio
stations.
1
Press TUNER .
' AUTO INSTALL ... PRESS PLAY' is displayed.
»
2
Press .
All detected radio stations are stored.
»
Once complete, it tunes to the fi rst preset
»
radio station.
• To stop auto tuning, press 9 .
Reinstall and listen to radio stations
1
Press TUNER to select the tuner source.
2
Press and hold PROG for more than 2 sec-
onds to activate automatic program mode.
All available stations are programmed in the
»
order of waveband reception strength.
3
Press J/ K to select a preset number.
E Tip
• Detailed features and additional functions are
described in the user manual.
© Royal Philips Electronics N.V. 2009
All rights reserved.
Specifi cations are subject to change without notice.
Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners.
Printed in China
MCD802_12_QSG_V2.0