I Contents （目次） Specifications （総合仕様; Specifications - Yamaha MG10/2 Service Manual

I

SPECIFICATIONS

I
General Specifications
Frequency Characteristics (ST OUT)
Total Harmonic Distortion (ST OUT)
1
Hum and Noise
Maximum Voltage Gain 2
Monaural/Stereo Input Gain Control
Monaural/Stereo High Pass Filter
Crosstalk (1 kHz)
Monaural/Stereo Input Channel Equalization:
3
Max. Variation
Monaural/Stereo Input Peak Indicator
Level Meters
Phantom +48 VDC Power (Balanced input)
Included Accessory
Option
Power Supply
Power Consumption
Max. Dimensions (W x H x D)
Weight
Where 0 dBu = 0.775V and 0 dBV = 1 V
1
Measured with 12.7 kHz, -6 dB/oct. low pass filter (equivalent to 20 kHz, -∞ filter).
(CH MIC INPUT to ST, AUX, EFFECT SEND)
2
Turning PAN/BAL to left or right.
3 Shelving turnover/rolloff frequency: 3 dB before maximum cut or boost.
20 Hz-20 kHz +1 dB, -3 dB @+4 dBu, 10 kΩ (with gain control at maximum level)
0.1 % (THD+N) @+14 dBu, 20 Hz-20 kHz, 10 kΩ (with gain control at maximum level)
(CHs 1 and 2)
-128 dBu Equivalent input noise (CHs 1 and 2)
-100 dBu Residual output noise (ST OUT)
-87 dBu (91 dB S/N) ST, Master fader at nominal level and all Ch at minimum level.
-85 dBu (89 dB S/N) All channel mix controls at minimum level.
ST, Master fader and one Ch fader at nominal level.
-64 dBu (68 dB S/N)
(CHs 1 and 2)
→
60 dB CH MIC INPUT CH INSERT OUT
→
76 dB CH MIC INPUT ST OUT
→
64.2 dB CH MIC INPUT REC OUT
→
70 dB CH MIC INPUT AUX SEND1 (PRE)
→
76 dB CH MIC INPUT AUX SEND2 (POST)
→
76 dB ST CH MIC INPUT ST OUT
→
50 dB ST CH LINE INPUT ST OUT
→
41 dB ST CH LINE INPUT AUX SEND1 (PRE)
→
47 dB ST CH LINE INPUT AUX SEND2 (POST)
→
26 dB ST CH INPUT ST OUT
→
12 dB AUX RETURN ST OUT
→
23.8 dB 2TR INPUT ST OUT
44 dB variable
80 Hz 12 dB/octave
-70 dB between input channels
-70 dB between input/output channels (CHs 1 to 6)
+/-
15 dB
HIGH 10 kHz shelving
MID 2.5 kHz peaking
LOW 100 Hz shelving
On each channel: red indicator lights if post-EQ signal (on ST channels, if either post-EQ sig-
nal or post-mic-amp signal) comes within 3 dB of the clipping level.
Two 12-point LED meters [Stereo (L, R)]
Peak point: red indicator
+5, +3, +1, and 0 points: yellow indicators
-1, -3, -5, -7, -10, -15, -20: green indicators
Supplied when Phantom +48 V switch is ON.
Power adaptor (PA-10)
Microphone-stand adaptor (BMS-10A)
USA and Canada: 120 V AC, 60 Hz
Europe: 230 V AC, 50 Hz
Australia: 240 V AC, 50 Hz
Korea: 220 V AC, 60 Hz
China: 220 V AC, 50 Hz
19 W
251 x 65 x 290.5 mm
1.8 kg
MG10/2
3