Download  Print this page

Specifications - Mitsubishi Electric PAR-F27MEA-US Instruction Book

Hide thumbs
   

Advertisement

[PROCEDURE]
1. Set the air conditioner to the off state with the remote controller [ON/OFF] button. The remote controller display shifts to the OFF window display
shown at the left.
2. When the [CHECK] and [MODE] buttons 1 are pressed and held down at the same time for two seconds, the remote controller switches to the
remote controller function selection mode and the "OPERATION MODE DISPLAY SELECTION MODE" window appears. The other three modes can
be selected by operating the [SET TEMP.] (
OPERATION MODE DISPLAY SELECTION MODE (When you want to change the AUTO mode display)
• "AUTO" "COOL/HEAT" flashes and "ON" or "OFF" lights. Each time the [TIMER SET (
"OFF" display is switched.
CENTRALLY CONTROLLED
DRY
COOL
DAILY
AUTO
AUTO
TIMER
AUTO OFF
ON
OFF
AUTO
FAN
FAN
CLOCK
SPEED
CHECK
SET TEMP.
REMAINDER
HEAT
VENTILATION
STAND BY
ERROR CODE
DEFROST
• When "ON" was selected, "AUTO" "COOL" or "AUTO" "HEAT" is displayed during AUTO mode operation.
• When "OFF" was selected, only "AUTO" is displayed during AUTO mode operation.
ROOM TEMPERATURE DISPLAY SELECTION MODE (When you want to change room temperature display/no display)
• "88 °C" flashes at the room temperature display and "ON" or "OFF" lights. Each time the [Time selection (
state, the "ON" and "OFF" display is switched.
CENTRALLY CONTROLLED
DRY COOL
DAILY
AUTO
AUTO
TIMER
AUTO OFF
ON
OFF
AUTO FAN
FAN
CLOCK
SPEED
CHECK
SET TEMP.
REMAINDER
HEAT
VENTILATION
STAND BY
ERROR CODE
DEFROST
• When "ON" was selected, the room temperature is continuously displayed in the ON window.
• When "OFF" was selected, the room temperature is not displayed in the ON window.
SET TEMPERATURE RANGE LIMIT MODE (When you want to change the set temperature adjustment range)
1) Cool/dry mode temperature selection
"COOL/DRY" and "LIMIT TEMP." light on the display and the set temperature adjustment range in the cool (dry) mode is displayed.
The lower limit temperature of the set temperature display flashes. This temperature value can be set and changed.
[Lower limit temperature adjustment range]: 65 °F
fixed. Only the lower limit temperature can be changed.)
CENTRALLY CONTROLLED
DRY COOL
DAILY
AUTO
AUTO
TIMER
AUTO OFF
ON
OFF
AUTO FAN
FAN
CLOCK
SPEED
CHECK
SET TEMP.
REMAINDER
HEAT
VENTILATION
STAND BY
ERROR CODE
DEFROST
[When set temperature adjustment range in cool/dry mode is 65 °F to 87 °F]
2) Each time the [TIMER SET (
temperature adjustment range.
CENTRALLY CONTROLLED
DRY COOL
DAILY
AUTO
AUTO
TIMER
AUTO OFF
ON
OFF
AUTO FAN
FAN
CLOCK
SPEED
CHECK
SET TEMP.
REMAINDER
HEAT
VENTILATION
STAND BY
ERROR CODE
DEFROST
[When set temperature adjustment range was set to 75 °F to 87 °F]
3) When the [SET TEMP. (
window.
"HEAT" and "LIMIT TEMP." light on the display and the heat mode set temperature adjustment range is displayed.
The upper limit temperature value can be changed by pressing the [TIMER SET (
selection.
Upper limit temperature adjustment range: 61 °F to 83 °F (61 °F
61 °F is fixed. Only the upper limit temperature can be changed.)
3. At the end of selection of each function, release the remote controller function selection mode and display the OFF window by pressing the [CHECK]
and [MODE] buttons 1 at the same time for two seconds.
4

Specifications

Item
mm
Size (H × W × D)
in
kg
Weight
lb
Power requirement
Power consumption
Environmental conditions
Material
) button 2 or (
1Hr.
SENSAOR
INSIDE
FILTER
CHECK MODE
[TIMER SET (
TEST RUN
NOT AVAILABLE
LIMIT TEMP.
1Hr.
SENSAOR
INSIDE
FILTER
CHECK MODE
[TIMER SET (
TEST RUN
LIMIT TEMP.
NOT AVAILABLE
87 °F (Mid temperature indoor unit: 55 °F
1Hr.
SENSAOR
INSIDE
FILTER
CHECK MODE
TEST RUN
NOT AVAILABLE
LIMIT TEMP.
)] button 4 is pressed, the lower limit temperature value is increased or decreased. Set it to the desired set
) or (
1Hr.
SENSAOR
INSIDE
FILTER
CHECK MODE
TEST RUN
NOT AVAILABLE
LIMIT TEMP.
)] button 2 is pressed after the setting above, the remote controller switches to the heat mode temperature selection
120 × 130 × 19
4-3/4 × 5-1/8 × 3/4
0.2
7/16
DC30 Power supplied from M-NET transmission line (Normally, power is received from the outdoor unit over the
indoor/outdoor unit M-NET transmission line.)
0.5 W
Temperature 32 (0) to 104 °F (40°C), humidity 30 to 90 % RH (No condensation)
PS
) button 3. Display the mode whose function you want to change.
) or (
CENTRALLY CONTROLLED
DRY
COOL
DAILY
TIMER
AUTO OFF
AUTO
FAN
CLOCK
CHECK
SET TEMP.
HEAT
) ((
))] button
STAND BY
DEFROST
CENTRALLY CONTROLLED
DRY COOL
DAILY
TIMER
AUTO OFF
AUTO FAN
CLOCK
CHECK
SET TEMP.
HEAT
) ((
))] button
STAND BY
DEFROST
) or (
83 °F for mid temperature indoor unit also) (The lower limit temperature
Contents
)] button 4 is pressed in this state, the "ON" and
1Hr.
SENSAOR
AUTO
AUTO
INSIDE
ON
OFF
FAN
SPEED
REMAINDER
FILTER
CHECK MODE
VENTILATION
TEST RUN
ERROR CODE
NOT AVAILABLE
LIMIT TEMP.
)] button 4 is pressed in this
) or (
1Hr.
SENSAOR
AUTO
AUTO
INSIDE
ON
OFF
FAN
SPEED
REMAINDER
FILTER
CHECK MODE
VENTILATION
TEST RUN
LIMIT TEMP.
ERROR CODE
NOT AVAILABLE
87 °F) (Upper limit temperature 87 °F is
)] button 4, the same as cool/dry mode temperature
8

Advertisement

   Also See for Mitsubishi Electric PAR-F27MEA-US

   Related Manuals for Mitsubishi Electric PAR-F27MEA-US

Comments to this Manuals

Symbols: 0
Latest comments: