Download  Print this page

How To Use - Panasonic NI-L70SR Operating Instructions Manual

Electric cordless steam iron
Hide thumbs

Advertisement

See
section
"
HOW
TO CONTROL TEMPERATURE
"
and
the following
charts:
Temperature
Level
Steam/Dry
Selector
Position
LOW
MtU
HIGH
Dry
(Non-Steam)
Regular
Steam
5.
Hold
the
iron
horizontally
and
move
the
Steam/Dry
Selector
into
the
desired
steam
position
after
the
Temperature
Control
light
turns
on
continuously.
You can
then
start ironing.
Note:
Anti-Drip
System
will
activate
when
the
temperature
of
the Soleplate's surface
drops. At the
same
time,
the
steam
will
stop;
it
is
not
a
sign
of
malfunction
when
you hear a
clicking
sound.
In
this situation,
you have
to
put
your
iron
back on
the
Power Base
to
reheat.
HOW
TO USE
AS A DRY
IRON
1
.
Move
the
Steam/Dry
Selector
to
the
Dry
position.
2.
Plug the cord
into
a standard
120V-60Hz
electrical outlet.
3.
Set
the
iron
on
the
Power Base
securely.
The
green
"
OFF
"
light
will
turn on.
NOTE:
If
the
green
light
does
not
turn on,
replace the
iron
on
the
Power Base
again, or
the
Temperature
Control
Pad
cannot
function.
4.
Push
the
"
SET
"
Pad
until
the red
blinking
light
reaches your
desired
temperature
level.
Wait
until
the
Temperature
Control
light
turns
on
continuously.
You
can
then
start ironing.
SPECIAL
FUNCTIONS
1
.
Jet
of
Steam
The"Jet
of
Steam"feature provides
extra
steam
which
goes deep
into
the
garment and
is
helpful
for
removing
stubborn
wrinkles.
The
"Jet of
Steam"
feature
operates
properly
only
in
the
"HIGH"
indication
area
of
the
"SET" Pad
when
steam
or dry
ironing
( If
used
at
lower
setting,
water
spotting
will
occur
because
the
iron
is
not hot
enough
to
change
water
to
steam
).
If
you have
not
used
the
"
Jet
of
Steam
"
feature
for
a
long
time,
it
is
necessary
to
clean the
inside
of
the
iron
before using
this
feature
on any
clothes
to
be
ironed.
Simply
test
the
"Jet of
Steam"
feature several
times
away
from
the
ironing
board
and
clothes
to
be
ironed.
This
will
prevent
brown
spotting or
water
spotting
on
the
clothes.
1
.
Fill
iron
with water.
See
section
"
HOW
TO
FILL
WITH
WATER
".
2.
Plug the cord
into
a standard 120V-
60Hz
electrical outlet.
3.
Set
the
iron
on
the
Power Base
securely.
The
green
"
OFF
"
light
will
turn on.
4.
Push
the
"
SET
"
Pad
to
the
"
HIGH
"
temperature
level.
The
red
light
starts blinking.
5.
Preheat
the
iron
until
the
light
turns
on
continuously, usually
about
1-2 minutes.
6.
Simply
pump
the
"
Jet
of
Steam
Button
"
when
steam
is
desired.
Pump
the
"
Jet
of
Steam
Button
"
several times
at
the
beginning
of
each
ironing
session.
7.
Allow
at least
5
seconds between uses
of "Jet of
Steam
Button
"
to
prevent water
spotting.
Use
a press
cloth
if
necessary.
-8-

Advertisement

loading

  Related Manuals for Panasonic NI-L70SR

This manual is also suitable for:

Ni-l71sr