Specifications - Mitsubishi Electric GT1665HS-VTBD Manual

Graphic operation terminal

Hide thumbs

page of 6

/ 6
Bookmarks

3. Specifications

3.1 General Specifications

Item

Operating ambient temperature

0 to 40C

Storage ambient temperature

-20 to 60C

Operating ambient humidity

10 to 90% RH, non-condensing (The wet bulb temperature is 39C or less.)

Storage ambient humidity

10 to 90% RH, non-condensing (The wet bulb temperature is 39C or less.)

Conforms to JIS

Vibration resistance

B3502 and

IEC61131-2

Shock resistance

Conforms to JIS B3502, IEC 61131-2 (147 m/s

Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and

Operating atmosphere

must be no direct sunlight. (Same as for saving)

2000 m (6562 ft) max.

Operating altitude

 or less

Overvoltage category

Pollution degree

2 or less

Cooling method

Self-cooling

*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.

When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,

and the sheet may be peeled off.

*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the

machinery within the premises. Category  applies to equipment for which electrical power is supplied from fixed facilities. The surge voltage withstand level for up to the

raged voltage of 300 V is 2500 V.

*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.

In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.

3.2 Performance Specifications

Item

Type

TFT color liquid crystal display (High intensity and wide angle view)

Screen size

6.5"

640  480 dots

Resolution

W132.5 (5.22)  H99.4 (3.91) [mm] (inch)

Display size

16-dot standard font: 80 characters  30 lines, 12-dot standard font: 106 characters  40 lines

Display character

Display

section

Display color

65536 colors

Display angle

Left/Right: 80 degrees, Top: 60 degrees, Bottom: 80 degrees (Horizontal format)

Intensity of LCD only

550[cd/m

]

Intensity adjustment

8-level adjustment

Life

Approx. 41,000h. (Operating ambient temperature: 25C)

LED type

Backlight

Backlight off/screen saving time can be set.

Type

Analog resistive film

Minimum 2  2 dots (per key)

Key size

To u c h

N u m b e r o f p o i n t s t o u c h e d

panel

Simultaneous presses not allowed. (Only 1 point can be touched.)

simultaneously

Life

1 million times or more (operating force 0.98N max.)

Flash memory (Internal), for storing project data (15Mbytes) and OS

Memory

C drive

Life (Number of write times): 100,000 times

Buzzer output

Single tone (tone length adjustable)

Operation switch

6 switches (6 contacts/common), N/O contact, Maximum rating 10mA/24VDC, Life: 1,000,000 times

1 switch (single wiring) (IDEC HE3B-M2PB), Enable switch (deadman switch) 3-position system of OFF

Grip switch

2 N/O contacts, Maximum rating 1A/24VDC (resistance load), Maximum rating 0.3A/24VDC (induction load), Life: 100,000

times

1 switch (single wiring) (IDEC XA1E-BV303R)

Switch

Emergency stop switch

2 N/C contacts, Maximum rating 1A/24VDC (resistance load), Maximum rating 0.3A/24VDC (induction load), Life: 100,000

times

1 switch (single wiring) (IDEC AS6M-2KT1PB)

Keylock switch

2-notch type (Manual stop at each position/A key can be inserted and removed on only the left side./On the right side, a key

(2-position switch)

cannot be removed./Two keys are provided.)

2-position, Maximum rating 1A/24VDC (resistance load), Maximum rating 0.3A/24VDC (induction load), Life: 100,000 times

Environmental protective structure

IP65F (valid when the external cable is connected, except for the connector conversion box side)

Specifications

Frequency

Acceleration

Half-amplitude

5 to 9Hz

3.5mm

Under intermittent

vibration

9 to 150Hz

9.8m/s

5 to 9Hz

1.75mm

Under continuous

vibration

9 to 150Hz

4.9m/s

, 3 times each in X, Y and Z directions)

Specifications

GT1665HS-VTBD

Item

External dimensions

Weight

Compatible software package

POWER LED

LED

Sweep Count

LED for operation switch display 6 LEDs, green (lighting control from the display section)

LED for grip switch display

10 times each in X,

Y and Z directions

Built-in clock precision

Type

Battery

Backup target

Life

RS-422/485

RS-232

Ethernet

Built-in

interface

USB

CF card

*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is impossible to completely avoid this symptom, as the liquid crystal display

comprises of a great number of display elements. Flickers may be observed depending on the display color.

Please note that these dots appear due to its characteristic and are not caused by product defect.

Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast adjustment. However, please note that

these phenomena appear due to its characteristic and are not caused by product defect.

There is a difference in the display brightness and the color tones between liquid crystal display panels. When using multiple liquid crystal display panels, please note

that there is an individual difference between them.

A crosstalk (shadow as an extension of the display) may appear on the liquid crystal display panel. Please note that it appears due to its characteristic.

When the display section is seen from the outside of the display angle, the display color seems like it has changed. Please note that it is due to its characteristic.

Please note that the response time, brightness and color of the liquid crystal display panel may vary depending on the usage environmental temperature.

When the same screen is displayed for a long time, an incidental color or partial discoloration is generated on the screen due to heat damage, and it may not disappear.

To prevent heat damage, the screen saver function is effective.

For details on the screen saver function, refer to the following.

 GT16 Handy GOT User's Manual

*2 Gradation inversion is a characteristic of liquid crystal displays. Please be forewarned that depending on the displayed color, the visualization may be difficult even within

the described view angle.

*3 The GOT screen saving/backlight off function prevents images from becoming permanently etched on the display screen.

 GT16 Handy GOT User's Manual

*4 The touch panel is analog resistive film-type. If you touch the panel simultaneously in 2 points or more, the switch that is located around the center of the touched point,

if any, may operate. Do not touch the panel in 2 points or more simultaneously.

*5 ROM in which new data can be written without deleting the written data.

*6 Note that this does not guarantee all user's operation environment. The protection is not applied when the interface environment protection cover or environment

protection back cover is removed. In addition, the product may not be used in environments under exposition of oil or chemicals for a long period of time, or in

environments filled with oil-mist.

*7 If the operating ambient temperature is other than 25C, the error may become large.

OFF

Specifications

GT1665HS-VTBD

W201 (7.91)  H230 (9.06)  D97 (3.82) [mm] (inch)

Approx.1.2kg (GT16 Handy GOT main unit only)

GT Designer3 Version1.14Q or later

1 LED

Lit in green: Power is correctly supplied.

Lit in orange: Screen saving and backlight not lit.

Blinks in orange/green: Blown back light bulb.