CONTENTS DISPLAY (4-line Dot Matrix DISPLAY)........P. 3 GETTING STARTED ..............P. 4 Power ON, OFF ................P. 4 Display Contrast Adjustment.............P. 4 Mode Selection .................P. 4 Calculator Set-up Menu ............P. 5 Before Using the Calculator ............P. 7 INPUTTING EXPRESSIONS AND VALUES ........P. 8 Input Capacity ................P.
How to use the Slide Cover Open or close the cover by sliding as shown in the figure. OPEN CLOSE DISPLAY (4-line Dot Matrix DISPLAY) <Status Indicators> : Shift key : Alpha key : Independent memory : Store memory : Recall memory STAT : Statistics mode : Degree Mode...
GETTING STARTED Power ON, OFF First time operation: 1. Pull out the battery insulation sheet, then the battery will be loaded. 2. Press to reset the calculator. Power ON: When is pressed. Power OFF: are pressed. When the calculator is not used for about 7 minutes, it will automatically power off.
Operation Mode Indicator COMP Normal calculation STAT Statistical calculation STAT TABLE Function Table calculation Initial mode is COMP mode. Calculator Set-up Menu Press to enter the Calculator Set-up Menu; press for next / previous page. Press To select the calculator input & output format [1] Maths or [2] Line [1] Maths –...
Page 6
To select the angle unit [3] Deg, [4] Rad or [5] Gra [3] Deg: Angle unit in Degree [4] Rad: Angle unit in Radian [5] Gra: Angle unit in Gradient 90º = radians = 100grads To select display digit or notation [6] Fix, [7] Sci or [8] Norm [6] Fix: Fixed Decimal, [Fix 0~9?] appears, specify the number of decimal places by pressing [0] –...
To select the statistical display format [3] STAT ([1] ON or [2] OFF) [1] ON: Show FREQ (Frequency) Column in Statistical Data Input Screen [2] OFF: Hide FREQ (Frequency) Column in Statistical Data Input Screen To select the decimal point display format [4] Disp ([1] Dot or [2] Comma) [1] Dot: specify dot format for Decimal point result display [2] Comma: specify comma format for Decimal point...
INPUTTING EXPRESSIONS AND VALUES Input Capacity F-718S allows you to input a single calculation up to 99 bytes. Normally, one byte is used as each time you press one of the numeric keys, arithmetic keys, scientific function keys or . Some functions require 4 – 13bytes. , and the direction keys will not use up any bytes.
Page 9
Omit the multiplication sign and final close parenthesis. Example: 2 x log 100 x (1+3) = 16 Operation 1: Display 1 Including 2xlog(100) x (1+3) Operation 2: Display 2 2log(100)(1+3 Omitting Omitting *1. Omit multiplication sign (x) - Input before an open parentheses : 1 x (2+3) - Input before scientific functions that includes parenthesis: 2 x cos(30)
Page 10
Deleting and Correcting an Expression In insert mode: Move the cursor to the right of the character or function that needs to be deleted, then press In overwrite mode: Move the cursor under the character or function being deleted, then press Example: 1234567 + 889900 (1) Replace an entry (1234567 1234560)
Inputting and Display result in Maths Mode In Maths Mode, the Input and display result of fraction or certain functions (log, x , x , , 10 , e , Abs) is shown in Handwriting/Mathematics format. Example in Key in operation Display Maths mode Remark...
Page 12
Function Calculation Input Ranges Functions Input Range |x| <9×10 sinx |x| <157 079 632.7 |x| <1x10 |x| <9×10 cosx |x| <157 079 632.7 |x| <1x10 Same as sinx, except when |x| =(2n-1)×90 tanx Same as sinx, except when |x| =(2n-1)× /2 Same as sinx, except when |x| =(2n-1)×100 9.999 999 999x10 sinhx...
Page 13
Functions Input Range |x|,|y| 9.999 999 999x10 Pol(x,y) 9.999 999 999x10 9.999 999 999x10 Rec(r, ) : Same as sinx |a|,b,c <1x10 °′ ″ The display seconds value is subject to an error of +/-1 at the second decimal place |x|<1x10 Deciaml Sexagesimal Conversions...
Functions Input Range |x|<1x10 One-variable |x|<1x10 Statistical |FREQ|<1x10 calculation Two-variable |x|<1x10 Statistical |y|<1x10 calculation |FREQ| <1x10 • Errors are cumulative in the case of consecutive calculations, this is also true as internal consecutive calculation are performed in the case of ^(x √y, √, x!, nPr, nCr , etc.
Page 15
Fractions: a b/c, d/c Prefix symbol: (–) (negative sign) ˆ ˆ ˆ ˆ Statistical estimated value calculation: x, y, x1, x2 Multiplication where sign is omitted: Multiplication sign omitted immediately before , e, variables (2 , 5A, A, etc.), functions with parentheses (2 (3), Asin(30), etc.) Permutations, combinations: nPr, nCr 10th Multiplication and division: ×, ÷...
Calculation Stacks This calculator uses memory areas, called “stacks”, to temporarily store numeric value (numbers) and commands (+, –, x…) according to their precedence during calculations. The numeric stack has 10 levels and command stack has 128 levels. A stack error [Stack ERROR] occurs whenever you try to perform a calculation that exceeds the capacity of stacks.
BASIC CALCULATIONS Press to enter COMP mode. During the busy calculation, the calculator shows only the indicators (without any calculation result). You can press key to interrupt the calculating operation. Arithmetic Calculations • To calculate with negative values (exclude the negative exponent) enclose then with parentheses.
Page 18
Example in Key in operation Display Maths mode 23 + 7 23+7 2 x sin A = 1 2sin(A Clear memory Independent Memory • Independent memory uses the same memory area as variable M. It is convenient for calculating cumulative total by just pressing (add to memory) or (subtract from memory)
Fraction Calculations The calculator supports Fraction calculation and the conversions between Fraction, Decimal point, Mixed fraction and Improper fraction. • Specify the fraction calculation result display format by either mixed fraction (a b/c) or improper fraction (d/c) in set-up menu. •...
Percentage Calculations Example in Key in operation Display Maths mode To calculate 25% of 820x25% The percentage of 750÷1250% 750 against 1250 Degree-Minutes-Seconds Calculations Use degrees (hours), minutes and seconds key to perform a sexagesimal (base-60 notational system) calculation or convert the sexagesimal value into decimal value.
Replay & Multi-statements Replay Memory Function • Replay memory is only available in COMP mode. • After the calculation is executed, the calculation input and result will be stored in the replay memory automatically. • Pressing ) can replay the performed calculation input and result history.
FUNCTIONAL SCIENTIFIC CALCULATIONS Press to enter COMP mode. = 3.1415926535897932324 e = 2.7182818284590452324 Square, Root, Cube, Cube Root, Power, Power Root, Reciprocal and Pi Example in Key in operation Display Maths mode = 0.6217559776 0.6217559776 Logarithm, Natural logarithm, Antilogarithm and logab Example in Key in operation Display...
Press the corresponding number key for the angle unit you need. Then the display will show the Indicator accordingly. Convert an angle unit between “Degree”, “Radian” and “Gradient” by pressing Then, pressing , or will convert the displayed value into the selected angle unit. Example in Key in operation Display...
Random Number Generation : Generate a random number between 0.000 and 0.999. And the display result will be fraction format in Maths mode status. : Generate a random number between two specified positive integers. The entry is divided by “.” Example in Key in operation Display...
Quotient and Remainder Calculations “Quotient” (Q) is the result of a division problem, “Remainder” (r) is the value remaining in an integer division problem. The calculated quotient value (Q) and remainder (r) will be stored into memory variables “C” and “D” automatically assigned.
Display Values Exchange In Maths mode, pressing to change the calculation result value between fraction form Decimal form, form Decimal form, √ form Decimal form. In Line mode, pressing to ONLY change the calculation result value between fraction form Decimal form, the other and √...
STATISTICAL CALCULATIONS Press to enter Statistical calculation mode and “STAT” indicator lights up. Press (Type) to select the calculation type. Statistical Type Selection There are 8 types of Statistical Calculation, after entered the Statistical Type Selection screen, then press the number to select the type of Statistic Calculation.
• After turned on Data Frequency “FREQ” in calculator’s setup menu, the FREQ column will be added into the above screen. • The followings are the maximum number of line for data input. Statistic type FREQ ON FREQ OFF Single Variable (only x input) 2 Variable (x &...
Statistical Calculation Screen After inputting the STAT Data, press to enter Statistical Calculation screen. Statistical Calculation screen are in Line mode for input & output Display Use Statistical Menu to calculate the Statistical result. (S-SUM, S-VAR, S-PTS, Reg). Statistical Menu In Statistical Data Input screen or Statistical Calculation screen, you can press to display the Statistical...
Page 32
Statistical calculation result in [4] S-SUM, [5] S-VAR, [6] S-PTS, [7] Reg STAT STAT Type Value Symbol Operation sub-menu S-SUM 1 & 2 variable Summation of all x value ∑x STAT Summation of all x value ∑x 2-variable Summation of all y value ∑y STAT only...
Please use the regression to estimate the effectiveness (estimate the value of y) if the advertisement expenses X=30, and estimate the advertisement expenses level (estimate the value of X ) for effectiveness y = 50. Key in operation Display (Quad) 48.69615715 31.30538226 -167.1096731...
Page 35
3. Input the start, end & step information • Input the value, press to confirm on the following screens • Input expression and display result value in following screens are in Line mode status • There are maximum of 30 x-values for generate function table.
BATTERY REPLACEMENT When the display characters are dim or show the follow message on the screen, turn the calculator off and replace the lithium battery immediately. LOW BATTERY Please replace the lithium battery using the following procedures, 1. Press to power off the calculator. 2.
• Do not under any circumstances dismantle his device. If you believe that the calculator is not functioning properly, either bring or mail the device together with the guarantee to service representative of Canon Business office. • Never dispose the calculator improperly such as burning;...