Additional Safety Instructions For Batteries And Chargers - Black & Decker CS36BS Original Instructions Manual

Labels on tool
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not expose the battery to heat.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the appliance/tool.
u
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not damage/deform the battery pack either by puncture
u
or impact, as this may create a risk of injury and fire.
Do not charge damaged batteries.
u
Under extreme conditions, battery leakage may occur.
u
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions below.
u
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Chargers
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to the
voltage on the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Use your BLACK+DECKER charger only to charge
u
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
u
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
(Original instructions)
The appliance/tool/battery must be placed in a well
u
ventilated area when charging.
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with
u
a regular mains plug.
Features
1. On/off trigger
2. Forward/reverse slider
3. Bit holder (1`/4" Hex Shank)
4. LED light
5. Bit storage
5a. Magnetic bit/screw holder
Assembly
Fitting and removing a drill bit or a screwdriver bit
(fig. A)
This tool uses screwdriver bits and drill bits with a 6.35 mm
(1/4") hexagonal shank. The tool can store 8 of these bits in
the bit storage compartment (5) or individually in the magnetic
bit/screw holder (5a) as shown in figure D.
To fit a bit, insert the bit shaft into the bit holder (3).
u
To remove a bit, pull the bit shaft out of the bit holder (3).
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Before first use, the battery must be charged for at least
u
10 hours.
Charging the battery (fig. B)
Insert the charger plug (7) into the charger connector (6).
u
Plug in the charger (7).
u
Leave the tool connected to the charger for
u
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40°C.
ENGLISH
10 hours.
5