Sleep Operation - Haier HSU-26HEK03/R2(DB)/I Operation Manual

Operation

Sleep Operation

Press button to enter additional options.
When display cycles to ,
Then press to enter sleep function.
1. Operation Mode
In COOL, DRY mode
1 hour after SLEEP mode starts, the temperature will become 1°C higher
than the temperature setting. After another hour the temperature rises by
another 1°C. The unit will run for a further 6 hours. The temperature is higher
than the temperature setting, so that the room temperature won't be too cold
for you to sleep.
SLEEP operation starts
1 hr
Rises 1
1 hr
Temp.setting
In COOL, DRY mode
2. In HEAT mode
1 hour after SLEEP mode starts, the temperature will become 2°C lower than
the temperature setting. After another hour, the temperature decreases by a
further 2°C. After another 3 hours, the temperature will rise by another 1°C. The
unit will run for a further 3 hours. The temperature is lower than the temperature
setting, so that the room temperature won't be too hot for you to sleep.
Temp.setting
1 hr Decreases 2
1 hr
SLEEP
operation starts
In HEAT mode
3. In AUTO mode
The unit operates in the corresponding sleep mode for the automatically
selected operation mode.
4. In FAN mode
The SLEEP function does not operate in FAN mode.
5. Set the fan speed change when sleeping
If the fan speed is high or medium, you can set it to lower the fan
speed after you go to sleep. If it is already set at low fan speed,
it is unchanged.
Note
When the TIMER function is set, the sleeping function can't be
set up. After the sleep function is set up, if you reset the
TIMER function, the sleep function will be cancelled.
3
will
SLEEP operation stops
Approx.6hrs
Rises 1 O C
O C
Unit stop
Unit stop
C
O
Decreases 2 C
O
3 hrs
Rises 1 C
3 hrs O
SLEEP
operation stops
Timer On-Off Operation
1. After unit starts, select your desired operation mode.
2. Press the TIMER button to change to TIMER mode. Every time the button is
pressed, the display changes as follows:
0.5h 0.5h
TIMER ON TIMER OFF TIMER ON-OFF
Remote controller:
Then select your desired TIMER mode (TIMER ON or TIMER OFF or TIMER
ON-OFF). "ON" or "OFF" will
3. Press / button to set the time.
Press the button for each time, setting time in the
by 0.5 hour every time and after 12 hours, increased by 1 hour every time.
Press the button for each time, setting time in the
decreased by 0.5 hour every time and after 12 hours, decreased by
1 hour every time. It can be adjusted within 24 hours.
4. timer setting
After adjusting the time, press the
ON or OFF button will not
5. Cancel timer setting
Press the timer button repeatedly until the time display does not show.
Hints:
After replacing batteries or a power failure, the time setting should be reset.
DRED Operation
(This function is unavailable on some models.)
Haier Peaksmart enabled air-conditioners have a Demand Response Mode display
on the indoor unit.
The display could be labelled d1, d2, d3 (wording may differ model to model).
These modes are described in more detail below:
M o e d D p s i y a l e D r c s t p i n o i
Your air-conditioner will continue
to cool or heat during the peak
DRM3 d3 demand event. The energy
consumed by your air-conditioner
is capped to 75%.
Your air-conditioner will continue
to cool or heat during the peak
DRM2 d2 demand event. The energy
consumed by your air-conditioner
is capped to 50%.
Your air-conditioner is still tuned
on and the fan will continue to
DRM1 d1 operate. Your compressor is
turned off and cool/hot air will no
longer be generated
BLANK
0.5h 0.5h
TIMER OFF-ON
12 hours increased
12 hours
button and the time. The
any more.
W h t a o t o d
No action is required.
No action is required.
DRM1 mode is only activated during
emergency demand management
situations. This mode will automatically reset
the device within 2 hours .If your air-con is in
this mode for longer than 2 hours please
contact Energex on 13 12 53.