For European Countries; Fig.11 - Makita 2704 Instruction Manual

For the button type switch
► Fig.13: 1. Switch
CAUTION:
• Before operation, make sure that the tool is
turned on and off.
To start the tool, press the ON ( I ) button.
To stop it, press the OFF ( O ) button.
Sub table (R)
► Fig.14: 1. Lever
► Fig.15: 1. Sub table (R)
This tool is provided with the sub table (R) on the right
side of the main table. To use the sub table (R), raise
both levers on the front right side, pull out the table (R)
fully and then lower the levers to secure it.
When using the sub table (R ), locate the scale plate
on the sub table after loosening the screw on it with
a screwdriver so that it becomes successive with the
scale plate on the main table.
► Fig.16: 1. Scale plate 2. Screw
Sub table (back)
(optional accessory for other than
European countries)
► Fig.17: 1. Sub table (back) 2. Screw
To use the sub table (back), loosen the screws on the
left and right hand sides under the table and pull it out
backwards to the desired length. At the desired length,
tighten the screw securely.
NOTE:
• When using the sub table (back ) during use of
the rip fence, pull out the sub table (back) more
than 50 mm so that it does not hit against the
top end of the rip fence.
Sub table (L) (optional accessory)
► Fig.18: 1. Screw 2. Sub table (L)
Sub table (L) (optional accessory) can be installed on
the left side of the table to obtain wider space.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
The tool is shipped from the factory with the saw blade
and blade guard not in the installed condition. Assemble
as follows:
Installing or removing saw blade
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the
blade.
• Use only the Makita socket wrench provided to
install or remove the blade. Failure to do so may
result in overtightening or insufficient tightening
of the hex bolt. This could cause an injury.
• Use the following saw blade. Do not use saw
blades which do not comply with the character-
istics specified in these instructions.
For Model Max. dia.
2704 260 mm
CAUTION:
• Check the arbor hole diameter of the blade
before installing the blade. Always use the
correct ring for the arbor hole of the blade you
intend to use.
► Fig.19: 1. Offset wrench 2. Hex nut 3. Wrench
Remove the table insert on the table. Hold the outer
flange with the offset wrench and loosen the hex nut
counterclockwise with the wrench. Then remove the
outer flange.
Assemble the inner flange, ring, saw blade, outer flange
and hex nut onto the arbor, making sure that the teeth
of the blade are pointing down at the front of the table.
Always install the hex nut with its recessed side facing
the outer flange.
► Fig.20: 1. Inner flange 2. Ring 3. Saw blade
4. Outer flange 5. Hex nut
For all countries other than European
countries
CAUTION:
• The silver ring 25.4 mm in outer diameter is
factory-installed onto the spindle. The black ring
25 mm in outer diameter is included as standard
equipment. Before mounting the blade onto the
spindle, always be sure that the correct ring for
the arbor hole of the blade you intend to use is
installed onto the spindle.

For European countries

CAUTION:
• The ring 30 mm in outer diameter is factory-in-
stalled between the inner and outer flanges.
• Keep the flange surface clean of dirt or other
adhering matter; it could cause blade slippage.
Be sure that the blade is installed so that
the teeth are aligned in the cutting (turning)
direction.
To secure the blade in place, hold the outer flange with
the offset wrench, then tighten the hex nut clockwise
with the wrench. BE SURE TO TIGHTEN THE HEX
NUT SECURELY.
► Fig.21: 1. Offset wrench 2. Wrench
12 ENGLISH
Min. dia. Blade thickness
230 mm 1.8 mm or less 2 mm or more
Kerf