Entering Letters/Characters; Specifications; Questions And Answers - Siemens Gigaset AS180DUO Manual

Hide thumbs

Advertisement

Appendix

Entering letters/characters

Press the relevant key the number of times indi-
cated.
Briefly press the hash key
"Abc" to "123" mode, from "123" to "abc" mode and
from "abc" to "Abc" mode.
Standard characters
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x
1
1)
1 £ $ ¥ ¤
2
a
b
c
2
ä
I
d
e
f
3
ë
4
g h
i
4
ï
5
j
k
l
5
L
m n o 6
ö ñ ó
M
p
q
r
s
7
N
t
u
v
8 ü ú ù û
O
w x
y
z
9
Q
.
,
?
!
0 +
P
*
/
(
)
< = > %
#
# @
\
Abc
123
-->
-->
123
abc
1) Space

Specifications

Recommended batteries
Technology:
Nickel-metal-hydride (NiMH)
Size:
AAA (Micro, HR03)
Voltage:
1.2 V
Capacity:
400–800 mAh
We recommend the following types of battery:
GP 550/700 mAh
Yuasa Phone 700/800 mAh
Peacebay 550/650 mAh
(Valid at the time of going to press)
The handset is supplied with recommended batter-
ies.
Base station power consumption
In standby mode
– Handset in base station
– Handset outside base station
During a call
General specifications
DECT standard
GAP standard
Range
Base station power supply
Environmental conditions
in operation
#
to switch from
á
à
â
ã
ç
é
è
ê
í
ì
î
ò
ô
õ
ß
ÿ
ý æ ø
å
-
:
¿
¡
"
'
& §
approx. 1.3 W
approx. 1.3 W
approx. 1.5 W
is supported
is supported
up to 300 m outdoors
up to 50 m indoors
230 V ~/50 Hz
+5°C to +45°C, 20% to
75% relative humidity
11

Questions and answers

If you have any queries about the use of your
telephone, visit our website at
www.gigaset.com/customercare
for 24-hour support. The table below contains a list
of common problems and possible solutions.
Problem
Nothing
appears in the
display.
No wireless
connection to
the base sta-
tion, Base
flashes in the
display.
;
_
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
Cause
Solution
The handset is not
Press the end call
a
switched on.
key
5 seconds or place
the handset in the
base station.
The batteries are
Charge or replace the
flat.
batteries.
The handset is
Move the handset
outside the range
closer to the base
of the base sta-
station.
tion.
¢
The handset is not
Register the handset
registered.
page 9.
The base station is
Check the mains
not turned on.
connector on the base
station
The phone cord
Please always use the
supplied has not
phone cord supplied
been used or has
or ensure that the
been replaced by
pin connections are
a new cord with
correct when purchas-
the wrong jack
ing from a retailer:
connections.
3-4 assignment of
telephone leads/EURO
CTR37.
You have entered
Reset the system PIN
¢
the wrong
to the default 0000
system PIN.
page 10.
All handsets are de-
registered. All set-
tings are reset. All
lists are deleted.
for approx.
¢
page 3.

Advertisement

loading