Mounting The Swivel And Tv To The Stand; Making Basic Connections To The Tv - Philips Cineos HDTV Monitor with Pixel Plus Quick Use And Setup Manual

Hdtv monitor with pixel plus
Table of Contents

Advertisement

Mounting the Swivel and TV to the Stand

1
Install the plastic position pins in the stand.
2
Place the TV and mounted swivel on the stand, aligning the
front and sides of the TV with the front and sides of the
stand. This will help properly seat the TV on the position-
ing pins and align the pre-drilled holes on the stand and
swivel. You do not need the rubber bumpers and long
screws if you have already attached the swivel to the TV.
3
Use the supplied screws (2) and screw key to fasten the swivel to
the stand. Install the back cover by sliding it up into the groove
above the opening, the slide into the lower groove.
Note: If accessories and cables protrude from the stand, leave the
back cover off.
4
Place accessory devices—HD satellite receiver, cable box, DVD
player, or VCR, for example—inside the stand. (See below and
Directions for Use manual for connection information.) Route the
power cords through the opening in the bottom of the stand shelf,
and route the connection cables through the openings in the back of
the stand.
5
Before swiveling the TV, make sure you have left enough slack in
the cords of any connected accessory devices. This will prevent
damage to the cords.
3
NOTE:
Installing these
screws
reduces the
risk of the TV
sliding.
Screws
Placing the TV on the Stand
without the Swivel
If you should decide not to purchase the optional swivel, you can
place the TV directly on the stand.
• First locate the nut and washer for each supplied rubber locator
(2).
• Place the rubber locators over the pre-drilled holes in the stand.
• Place the washer and nut on each rubber locator.
• Tighten each nut.
• Place the TV and mounted swivel on the stand, aligning the
front and sides of the TV with the front and sides of the stand.
This will help properly seat the TV. The rubber locators will
prevent the TV from sliding.
Cable TV
Connect the cable TV signal to the TUNER jack on the back of
the TV. See page 8 for details on using Autoprogram to store chan-
nels in the TV's memory.
NOTE: This connection will supply stereo sound to the TV if it is
being broadcast by the station you are watching.
1
4

Making Basic Connections to the TV

Positioning
Pins
DVD619
DVD/CD PLAYER
OPEN/CLOSE
STOP
PLAY
PAUSE
STANDBY-ON
GUIDE
PREV
NEXT
POWER
SELECT
POWER
INFO
HIGH DEFINITION
Rubber Locators
DVI
G
S-VIDEO
R
L
V
Pr
Pb
Y
R
L
V
R
L
R
L
R
L
V
G
S-VIDEO
RGB+HV
Pr
Pb
Y
R
L
STANDARD/
HD INPUTS
TUNER
STANDARD/
Pr
Pb
Y
HD INPUTS
R
L
3
2
5
Back of TV
DVI
G
S-VIDEO
R
L
V
Pr
Pb
Y
R
L
V
R
L
R
L
R
L
V
G
S-VIDEO
RGB+HV
Pr
Pb
Y
R
L
STANDARD/
HD INPUTS
Pr
Pb
Y
STANDARD/
HD INPUTS
R
L
Connect the incoming cable
TV signal to the TUNER
jack on the back of the TV.
DVI
G
S-VIDEO
R
L
V
Pr
Pb
Y
R
L
V
R
L
R
L
R
L
V
G
S-VIDEO
RGB+HV
R
L
Pr
Pb
Y
STANDARD/
HD INPUTS
TUNER
Pr
Pb
Y
STANDARD/
R
L
HD INPUTS
Incoming
Cable TV
Signal
TUNER

Advertisement

Table of Contents
loading

Table of Contents