Specific Safety Rules - Black & Decker BDCR20 Instruction Manual

power t ool i nunexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) if devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot be
controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures
reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation, if damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control
g) Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack:
b) Use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
c) When battery pack is not in use,
keep it away from other metal
objects like paper clips, coins, keys,
nails, screws, or other small metal
objects that can make a connection
from one terminal to another.
Shorting the battery terminals together
may cause bums or a fire.
d) Under abusive conditions,
liquid may be ejected from the
battery, avoid contact, if contact
accidentally occurs, flush with
water, if liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery may
cause irritation or bums.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power
tool is maintained.
SPECiFiC SAFETY RULES
• Hold power tool by insulated gripping
surfaces, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a "live" wire may
make exposed metal parts of the power
tool "live" and could give the operator an
electric shock:
• Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
• When not in use, place tool on its
side on a stable surface where it will
not cause a tripping or falling hazard.
Some tools with large battery packs will stand
upright but may be easily knocked over.
• Keep hands away from cutting area.
Never reach underneath the material for
any reason. Hold front of saw by grasping
the contoured gripping area. Do not insert
fingers or thumb into the vicinity of the
reciprocating blade and blade clamp. Do
not stabilize the saw by gripping the shoe.
• Keep blades sharp. Dull blades may
cause the saw to swerve or stall under
pressure.
• Use extra caution when cutting
overhead and pay particular attention
to overhead wires which may be hidden
from view. Anticipate the path of falling
branches and debris ahead of time.
• When cutting pipe or conduit ensure that they
are free from water, electrical wiring, etc.