Download  Print this page

Optimal Definition Profiles - Cisco TelePresence MX700 Administrator's Manual

Hide thumbs

Advertisement

Cisco TelePresence MX700 and MX800
Contents

Optimal definition profiles

Under ideal lighting conditions the bandwidth (call rate)
requirements can be substantially reduced.
The optimal definition profile should reflect the lighting
conditions in your room and the quality of the video input
(camera); the better the lighting conditions and video input,
the higher the profile. Then, in good lighting conditions, the
video encoder will provide better quality (higher resolution or
frame rate) for a given call rate.
In general, we recommend the optimal definition profile
set to Normal. However, if lighting conditions are good we
recommend that you test the endpoint on the various Optimal
Definition Profile settings before deciding on a profile.
Go to System Configuration on the web interface and
navigate to
Video > Input > Connector n > OptimalDefinition >
Profile
to choose the preferred optimal definition profile.
You can set a resolution threshold to determine when to allow
sending video at 60 fps. For all resolutions lower than this
threshold, the maximum transmitted frame rate will be 30 fps;
for higher resolutions, 60 fps will be possible if the available
bandwidth is adequate.
Go to System Configuration on the web interface and
navigate to
Video > Input > Connector n > OptimalDefinition >
Threshold60fps
to set the threshold.
The video input quality settings must be set to Motion for the
optimal definition settings to take any effect. With the video
input quality set to Sharpness, the endpoint will transmit the
highest resolution possible, regardless of frame rate.
Go to System Configuration on the web interface and
navigate to
Video > Input > Connector n > Quality
video quality parameter to Motion.
You can read more about the video settings in the
► System settings
chapter.
D15119.02 MX700 and MX800 Administrator Guide TC7.2, AUGUST 2014.
Introduction
Web interface
High
Typically used in dedicated video
conferencing rooms. Requires very good
lighting conditions and a good quality
video input to achieve a good overall
experience.
Under ideal conditions the bandwidth
requirements can be reduced by up to
50% compared to Normal.
to set the
System settings
Medium
Typically used in rooms with good and
stable lighting conditions and a good
quality video input.
The bandwidth requirements can be
reduced by up to 25% compared to
Normal.
Typical resolutions used for different optimal definition profiles, call rates and frame rates
Optimal Definition
Frame rate
Profile
768 kbps
Normal
1280 × 720
30 fps
Medium
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080
High
1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080
Normal
768 × 448
60 fps
Medium
1024 × 576
High
1280 × 720
Normal
1024 × 576
30 fps
Medium
1280 × 720
High
1280 × 720
Normal
640 × 360
60 fps
Medium
768 × 448
High
1024 × 576
H.265 is preferred over H.264, and the maximum bit rate for H.265 is 3 Mbps. When the user sets a higher bit
*
rate, the codec will still use H.265 at 3 Mbps as long as all codecs involved supports H.265.
132
Setting passwords
Normal
This setting is typically used in office
environments where the room is normally
to poorly lit.
Call rate
1152 kbps 1472 kbps 2560 kbps
4 Mbps
*
1280 × 720
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080
1024 × 576
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080
1280 × 720
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080
768 × 448
1024 × 576
1280 × 720
1280 × 720 1920 × 1080
1024 × 576
1024 × 576
1280 × 720 1920 × 1080 1920 × 1080
1280 × 720
1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080
www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved.
Administrator Guide
Appendices
Appendices
6 Mbps
*
1280 × 720
1280 × 720
1280 × 720

Advertisement

Table of Contents

   Also See for Cisco TelePresence MX700

This manual is also suitable for:

Telepresence mx800

Comments to this Manuals

Symbols: 0
Latest comments: