Download  Print this page

2-pole Magnet And Centering Magnet Adjustment; Centering Magnet Adjustment; 4-pole Magnet Adjustment; Blue Defocus Adjustment - Sony KP-51WS510 Service Manual

Color rear video projection.
Hide thumbs

Advertisement

Table of Contents
2-6. 2-POLE MAGNET AND CENTERING
MAGNET ADJUSTMENT
1. Set the picture mode to PRO and picture to MAX.
2. Either select the PJED Test Pattern dot hatch signal or apply an
external dot signal.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
4. Turn the focus VR on the focus block to the left (counter clockwise)
and set it to overfocus to enlarge the spot.
5. Adjust the CRT's 2-pole magnet so that the small bright spot is in the
center.
6. Align the focus VR on the focus block and set it for the best focus.
7. Apply a Monoscope signal to the set.
8. Adjust the H-CENTERING and V-CENTERING roughly by the
centering magnets.
9. Check 2-pole magnet adjustment. If necessary repeat steps 1-6.
10. Repeat steps 1 through 9 for the red CRT covering the green and
blue CRT lenses with lens caps to allow only red to show (or use the
method shown in the note below for turning off the CRTs individually
without using lens caps) and adjust the red focus control on the focus
block.
11. Repeat steps 1 through 9 for the blue CRT covering the red and
green CRT lenses with lens caps to allow only blue to show (or
use the method shown in the note below for turning off the CRTs
individually without using lens caps) and adjust the blue focus control
on the focus block.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams by controlling the service mode 2150P-2 1 RGBS.

2-7. CENTERING MAGNET ADJUSTMENT

Not required - Combined with 2-6 2-Pole And Centering Magnet
Adjustment.

2-8. 4-POLE MAGNET ADJUSTMENT

1. Set the picture mode to PRO and picture to MAX.
2. Receive the Dot signal.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
4. Turn the (green) focus VR on the focus block to the right (clockwise)
and set it to under-focus to reduce the spot.
5. Adjust the 4-pole magnet so that the small spot in the center of the
screen becomes round for green and red.
6. Adjust the blue spot to an oval shape X:Y=1:1.2
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams by controlling the service mode 2150P-2 1 RGBS.
������������������

2-9. BLUE DEFOCUS ADJUSTMENT

1. Setup: Apply a Dot Hatch Signal and set the mode to Pro Mode.
Change the color temperature to Cool in the user's menu.
2. Cover the red and green CRT lenses with lens caps to allow only blue
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
4. Turn the blue focus VR on the focus block to the right (clockwise) to
make the round dot oval.
5. Check the flare with a high luminance signal to make sure the flare is
minimal while the bright spot is located in the center, If not, readjust
the 2 and 4-pole magnets.
6. Check for uniformity on a 100% IRE to an all white signal.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams by controlling the service mode 2150P-2 1 RGBS.
— 17 —
KP-51WS510/57WS510/65WS510
��������������������
������������������������
D2
D1
Blue
D1:D2 = 1:1.2

Advertisement

Table of Contents

   Related Manuals for Sony KP-51WS510

This manual is also suitable for:

Kp-57ws510Ra-6aKp-65ws510

Comments to this Manuals

Symbols: 0
Latest comments: