Download  Print this page

Advertisement

Table of Contents
FUEL
TANK
Removal:
•Unloc
k
the seat
and
swi ng it
open.
•Turn
t he
fue
l
tap to the "OFF
"
position
,
slide
the hose
clamp down, and
pul
l the
fuel
hose
off
the tap.
•Unhook
the
rubber retainer
on the rear
of
the fuel
tan
k
by
pulling
both tabs
outward.
A. Rubber Retainer Tab
•Lift
up the rear end
of
the
fuel
tank,
and
pul
l
the
fu(.I
tan
k
off toward
the rear.
Installation:
•Make
su
re
that
the
rubber dampers
are
in
pl
ace,
and
install the ru
bber
retainer.
• Mount
the
fuel
tank and
hook
the
rubber
re
taine
r
onto
the
hook
pins.
Fit
the fuel
hose
back
onto
th
e
fuel tap,
and
slide
the
clamp back
into place.
•Push
the
seat
back down.
CARBURETORS
Removal:
•Remove
the fuel tank
(Pg. 39).
•Pull
out the
overflow
and
breather
tubes
from between
the
rear
of
the engine
and the
swing
arm.
•Loosen
the
carburetor
holder
clamp
and the
air cleaner
duct
clamp
for
each
carburetor,
and
slip
them
out of
place.
A. Carburetor Holder Clamp
8
.
Air Cleaner Duct
Clamp
DISASSEMBLY-ENGINE
INSTALLED 39
•Pu
ll
the c,trbu
re tors
off to the
rear and
out.
Be sure
not
to
damage the thro
ttl
e
cables.
''~-
•Turn
in fu
ll
y
the
lockn
u
ts
and
adjusting
nuts
at
t~e
,:~,._
upper
end
of the
th
ro ttle
cables so as
to
give the cab
ts
plenty of play.
-
~
@~:u:~@
:a~;~~;;rs t~it~~~~tt!~o:a:~e~a:~mpl:~~
.
may cause
throttle
cable damage.
·
•Loosen the locknuts and
turn
out the
cable
adjusters
on the lower
ends
of
the
throttle
cables all
the
way,
to
remove
them
from
the adjuster
brackets.
A. Adjusters
B. Lockouts
C.
Adjuster
Bracket
•Disconnect
the
cable
nip
ples
from the
pulley
.
Installation:
•Fit
the ni
pple
of
the decelerator throttle
cable
into
the rear socket in
the
pulley,
and
screw
the adjuiter
in
to
its
bracket.
Fit the
othe
r cable
nipple into
the
fron
t
socket
in
the
pulley,
and
install
the
adj uster
onto the
brac
ket.
A. Decelerator
Throttle
Cable
B. Accelerator Throttle Cable
•Cente
r
each adjus
te
r
in
place
in the
bracket,
and
tighten
the
locknuts.
•Make
su
re th at
the carburetor
hol
der clamps
and air
cleaner
duc
t
clamps
are in
place,
and
that the screw
heads are facing
outward.
•Slip the
carburetors
back
into
place.
•Check
that the
ducts and holders
are
all
properly
fitted
o
n the
carburetors, and
t ighten
the clamps.
•Rou te
the
carburetor overflow
tubes
(2) and
breather
tubes (2)
to the
rear or
the
engi ne.

Advertisement

Table of Contents

   Also See for Kawasaki Z250 1981

This manual is also suitable for:

Kz350 1981

Comments to this Manuals

Symbols: 0
Latest comments: