Download  Print this page

Advertisement

Table of Contents
296 SUPPLEMENT-1982 KZ305B
A.
Adjusting Nut
B. Locknut
•Back o
ut
both
the
belt
adjusting
nuts
fu lly,
and
push
ful ly the
wheel forward for easier
belt
removal.
• Remove
the. rear
wheel
(p.
296).
•Mark the direction of
belt rotation on the
belt with
chalk
so
that the
belt
can
be
rei nstalled in
t
he same
direction
to
ensure
longer
belt
life.
Remove the
engine
pulley
cover (p.
294).
• Remove the
engine
pulley
(P. 295).
Remove the
swing
arm.
Free
the belt
from
the
motorcycle.
Installation
Notes:
1. Be
sure that the belt
is
installed
in
the
s.ame
direc-
tion as
before
removal. When
instal ling a new
belt,
t
he
red
paint
mark
on
the
side
of
the belt
should
face
inwards
of
the
motorcycle
.
A.
Red Paint Mark
2.
Tighten the
engine
pulley
nut to
69
N-m
(7.0
kg·m,
51
ft-lb)
of torque.
3.
Bend the sides or t he
splined
washer over
the sides
of the
engine pulley
nut
4.
Check
t
hat
t
he
engine
pulley
cover
knock
pins
(2)
are in
place.
5.
Lubricate
the
swing
arm
pivot
(p.
232).
6.
Apply grease
to the cap
inner surfaces
and
install
the
cap
on each
side
of the swing arm
pivot
7.
Tighten
the
pivot
shaft nut
to
78 N-m
(8 .0
kg-m,
58
ft-lb)
of torque.
8.
Apply
a
litt
le
grease
to
inside surface
of t he hole
in
the
coupling where
the
rear
hub
fits.
9.
Check
to
see
that
the
wheel
coupli
ng,
coupling
collar, coup ling sleeve, rubber damper,
and
brake
panel
are
in
place.
"JO.
Adjust
the
drive
belt
tension
usi ng
the
tension gauge
(p. 293).
11.
Adjust
the rear
brake (p.
193).
REAR
WHEEL,
BRAKE
Refer
lo
p.p.
202
-
205,
noting
t
he follow
ing.
Removal:
• Raise the
rear
wheel
off
t
he
grou
nd.
•Remove
the
mufflers (p.
44).
Remove the
belt
guard.
• Take
out
the
cotter
pin, and remove the
,tXlc
nu
t
•Remove the
clip,
nu
t, lockwasher,
and
bolt
at
the
rear
end of
the torque
link.
A. Torque Link Nut
C. Adjusting Nut
B.
Clip
•Remove
the adjusting
nut
from
the
end
of the
brake
rod, and free
the rod from the cam
lever.
• Remove the spring
scat
and spring from the brake rod,
and
remove the
brake rod
joint
from the
brake
cam
lever.
Loosen
the left
and
right
belt adjuster
lock
nuts.
•Back out
both
the
belt adjusting
nu
ts evenly, and
push
fu
lly
the whee
l forward
fo
r
eas ier
wheel
removal.

Advertisement

Table of Contents

   Also See for Kawasaki Z250 1981

This manual is also suitable for:

Kz350 1981

Comments to this Manuals

Symbols: 0
Latest comments: