Download  Print this page

Programming An H.323 Qsig Network; Assigning The Hunt Pattern - Panasonic KX-NS1000 Installation Manual

Pure ip-pbx.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Table of Contents
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416

Advertisement

5.6 Programming an H.323 QSIG Network

There are 2 methods to programme the Virtual 16-Channel VoIP Gateway Card (V-IPGW16 card) to establish
VoIP communications between PBXs at different locations, as follows:
PBX code method
Extension number
method
Note
For a detailed explanation about each method, refer to "4.3 Private Network Features" in the Feature
Guide.
Portions of this software are © 1996–2006 RADVISION Ltd. All intellectual property rights in such
portions of the Software and documentation are owned by RADVISION and are protected by United
States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION
and its suppliers retain all rights not expressly granted.

5.6.1 Assigning the Hunt Pattern

The hunt pattern determines how to route incoming calls through virtual IP trunks to the PBX. The procedure
below demonstrates the process of programming the hunt pattern of the local PBX. After the hunt pattern at
the local PBX has been fully assigned, repeat the procedure for the hunt pattern at the remote PBX with the
appropriate setting values.
The caller dials the unique PBX code of the PBX to which the called party is
connected, in addition to the destination number.
The caller dials only the destination number of the called party to call through
PBXs at different locations (hence there are fewer digits to dial than with the
PBX code method).
1.
Status Light
2.
a.
Click Setup ® PBX Configuration ®
Configuration ® Slot.
b.
Click Virtual ® V-IPGW16.
c.
If the V-IPGW16 card's status light is green, move
the mouse pointer over the card, select Ous from the
menu that appears, and then click OK on the
dialogue box. The status light will turn red.
d.
Move the mouse pointer over the installed
V-IPGW16 card. A menu will be shown under the
mouse pointer.
e.
Click Shelf Property.
f.
Click Hunt Pattern.
a.
When using the PBX code method:
In the Leading Number cell, type the local PBX
code and extension starting digit.
When using the extension number method:
In the Leading Number cell, type the local extension
starting digit.
b.
Click OK to return to the Shelf Property screen.
5.6.1 Assigning the Hunt Pattern
Installation Manual
231

Advertisement

Table of Contents

   Related Manuals for Panasonic KX-NS1000

Comments to this Manuals

Symbols: 0
Latest comments: