Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems D1528ENR3
Summary of Contents for Alliance Laundry Systems D1528ENR3
- Page 1 Washer-Extractors STANDARD and PRO Controls Refer to Page 7 for Model Identification CFD32C_SVG Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) D1528ENR3 www.alliancelaundry.com April 2014...
-
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 4: Safety Information
Wear hand and eye protection when adding detergents and W023 chemicals. Always read and follow manufacturer’s instruc- tions on packages of laundry and cleaning aids. Heed all • Read all instructions before using the washer. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 5: Safety Decals
Common sense, caution and care must be exer- cised when installing, maintaining, or operating the washer. Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... - Page 6 Do not bypass any safety devices in the machine. WARNING Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage. W728 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
-
Page 7: Introduction
© D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 8: Replacement Parts
Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Ripon, Wisconsin Alliance International: +32 56 41 20 54 Wevelgem, Belgium © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3... -
Page 9: Cygnus Operation
3. Close the door by pushing the door handle toward the ma- balance conditions and may lead to premature bearing and seal chine. Refer to Figure 4 . failure. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... - Page 10 BLEACH Figure 5 6. If necessary, reduce the cycle’s water levels. Press the ECO Wash Keypad. Refer to Figure 6 . The ECO Wash LED lights © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
-
Page 11: Information Menu - Standard Control
Refer to Figure 9 . a. Press and hold the 1 keypad. b. While continuing to press the 1 keypad, press and release the 2 keypad. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 12: Pro Control
The display alternates between “tEMP” and the water temperature in °C or °F. Operational Keypad CFD1024R_SVG 1. Display 2. Start/Stop Keypad 3. Navigation Buttons Figure 11 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3... -
Page 13: Display Identification
3. Close the door by pushing the door handle toward the ma- balance conditions and may lead to premature bearing and seal chine. Refer to Figure 14 . failure. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... - Page 14 Fast Hot Chemical Sluice 1000 CHM2227N_SVG 2. Powder Detergent CFD815N_SVG b. BLEACH Figure 15 6. Start the cycle by pressing the Start/Stop keypad. Refer to Figure 16 . © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
-
Page 15: Functions Menu - Pro Control
1. To enter the Functions Menu, press and release the keypad 8. Predefined Cycle Start Time Icon under the menu icon. Refer to Figure 19 . Figure 20 2. The Functions Menu options are as follows: © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... - Page 16 NOTE: This symbol is only displayed in the Func- tions Menu if Load-Dependent Wash has been enabled for the cycle. Load-Dependent Wash can be enabled or disabled using the PC software, Cygnus Assist. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
- Page 17 3. The water temperature and soak time can be modified. adjust the selected number. To modify the soak temperature… Press the keypad under the water temperature icon. Refer to Figure 33 . © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT...
- Page 18 Time icon. Refer to Figure 39 . The Predefined Cycle stituted for one another. Start Time screen appears. Refer to Figure 40 . © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
-
Page 19: Information Menu - Pro Control
3. To exit the Functions Menu, press the Start/Stop keypad. Re- fer to Figure 19 . Figure 44 2. To modify the cycle... Information Menu – PRO Control © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... - Page 20 Refer to Figure 44 . d. Press the keypad under the check mark icon to confirm the cycle setting adjustment. Refer to Figure 44 . © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
-
Page 21: Tilting Option
NOTE: If the machine senses that it is not level during a cycle, the control will end the cycle and "Error 61: Home switch open while washing" will be shown in the display. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 22: Maintenance
3. Inspect steam hose connections for leaks (where applicable). warranty and could lead to expensive inverter drive re- 4. Inspect all chemical inlets, lines and connections for leaks. pair. © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 23: Monthly
EP2 grease into the grease injection ports located on the Cabinet Hard- 14, 18, 25, 65, 56-73 back of the machine. Refer to Figure 47 . mount 75 and 100 © D1528ENR3 Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT... -
Page 24: Quarterly
H042I_SVG 1. Cap 2. Steam Filter Element Figure 48 5. Tighten motor mounting bolt locknuts and bearing bolt lock- nuts. 6. Vacuum lint from motor vents. © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT D1528ENR3...
Need help?
Do you have a question about the D1528ENR3 and is the answer not in the manual?
Questions and answers