Download  Print this page

Installation; Remote Resources; Remote Resources Configuration - GE C30 Instruction Manual

Controller system.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416

Advertisement

REMOTE RESOURCES

Once teleprotection is enabled and the teleprotection input/outputs are configured, data packets are transmitted
continuously every 1/4 cycle (3/8 cycle if using C37.94 modules) from peer-to-peer. Security of communication channel
data is achieved by using CRC-32 on the data packet.
Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive. As such, they cannot be used
simultaneously. Once teleprotection inputs and outputs are enabled, direct inputs and outputs are blocked, and
vice versa.
NUMBER OF TERMINALS
NUMBER OF CHANNELS
set the
NUMBER OF CHANNELS
channels).
LOCAL RELAY ID NUMBER
multiplexers or modems, it is desirable to ensure that the data used by the relays protecting a given line is from the correct
relays. The teleprotection function performs this check by reading the message ID sent by transmitting relays and
comparing it to the programmed ID in the receiving relay. This check is also used to block inputs if inadvertently set to
loopback mode or data is being received from a wrong relay by checking the ID on a received channel. If an incorrect ID is
found on a channel during normal operation, the
event with the same name and blocking the teleprotection inputs. For commissioning purposes, the result of channel
identification is also shown in the
default value of "0" for the
channel systems, the same
has to be programmed on the receiving end.
NUMBER

5.3.17 Installation

5
SETTINGS  PRODUCT SETUP  INSTALLATION
 INSTALLATION
— To safeguard against the installation of a relay without any entered settings, the unit does not allow
RELAY SETTINGS
signaling of any output relay until
UNIT NOT PROGRAMMED self-test error message displays until the relay is put into the "Programmed" state.
— This setting allows the user to uniquely identify a relay. This name appears on generated reports.
RELAY NAME
5.4 Remote resources

5.4.1 Remote resources configuration

When the C30 is ordered with a process card module as a part of HardFiber system, an additional Remote Resources
menu tree is available in the EnerVista software to allow configuration of the HardFiber system.
5-118
— Specifies whether the teleprotection system operates between two peers or three peers.
— Specifies how many channels are used. If the
to "2." For a two-terminal system, the
,
TERMINAL 1 RELAY ID NUMBER
TELEPROT CH1 ID FAIL
STATUS  CHANNEL TESTS  VALIDITY OF CHANNEL CONFIGURATION
indicates that relay ID is not to be checked. On two- terminals two-
LOCAL RELAY ID NUMBER
LOCAL RELAY ID NUMBER
RELAY SETTINGS:
Not Programmed
RELAY NAME:
Relay-1
is set to "Programmed." This setting is "Not Programmed" by default. The
RELAY SETTINGS
NUMBER OF TERMINALS
NUMBER OF CHANNELS
, and
TERMINAL 2 RELAY ID NUMBER
or
TELEPROT CH2 ID FAIL
is transmitted over both channels; as such, only the
Range: Not Programmed, Programmed
Range: up to 20 alphanumeric characters
C30 CONTROLLER SYSTEM – INSTRUCTION MANUAL
CHAPTER 5: SETTINGS
is "3" (three-terminal system),
can set to "1" or "2" (redundant
— In installations that use
FlexLogic operand is set, driving the
actual value. The
TERMINAL 1 ID

Advertisement

Table of Contents

   Also See for GE C30

   Related Manuals for GE C30

Comments to this Manuals

Symbols: 0
Latest comments: