Download  Print this page

GE C30 Instruction Manual Page 141

Controller system.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416

Advertisement

CHAPTER 4: INTERFACES
Category
Block or gate
Message
affected
Error
Input
Unrecognized Parameter
(SYMBOL_ID,Name,SheetRefere
nce)
Warnings
When using the 'Reset OP' operand, a warning can appear indicating that this is a disabled feature. This means that the
Reset Settting's FlexLogic operand is set to OFF. Resetting of the relay can be done by pressing the reset button on the front
panel of the relay or by sending a Reset command through communications.
Table 4-4: Warning messages from compiling
Category
Block or
gate
affected
Minor warning
Input
Major warning
Tag-Out
Major warning
All
Minor warning
=VO
Minor warning
Input
Setting warning
Input
Major warning
Input
Major warning
Input
Setting warning
Input
Setting warning
Input
4.4.1.5 Rapidly add logic blocks in sequence
Blocks are added by clicking an element then clicking in the drawing area, or by dragging and dropping the element onto
the canvas. Blocks can be added rapidly in sequence, for example when you have inputs 1 to 10, without having to select
the element each time.
To rapidly add logic blocks:
1.
In Engineer, click File > Preferences. The window opens.
2.
Click the Editor entry.
3.
Enable the Repeat Symbol check box.
4.
Click the Ok button to save and exit from the window.
5.
In the logic diagram, select an element, then click in the drawing area to add it, click again to add a second box, and
so on.
C30 CONTROLLER SYSTEM – INSTRUCTION MANUAL
Description
An Input symbol is configured to an item that is not recognized by the
current order code and version. Possible cause: The order code and/or
version of the settings file was converted causing the input parameter to
become unavailable.
Message
Input set to unused VO
(SYMBOL_ID,Name,Sheet)
Tag-out not connected
(TAG_ID,Sheet)
Symbol not connected
(SYMBOL_ID,Name,Sheet)
Virtual Output n using default
name (VO_ID,Sheet)
Input using default name
(SYMBOL_ID,Name,Sheet)
Input using disabled feature
(SYMBOL_ID,Name,Sheet)
Input set to OFF
(SYMBOL_ID,Sheet)
Input set to ON
(SYMBOL_ID,Sheet)
Contact Output Operate is OFF
(SYMBOL_ID, Contacts)
Contact Output Seal-In is OFF
(SYMBOL_ID, Contacts)
FLEXLOGIC DESIGN AND MONITORING USING ENGINEER
Description
An Input symbol is using an unassigned Virtual Output
A Tag-Out symbol has no input
A symbol's input and/or output is not connected and is not part of a
VO block. Draw the input and/or output to the block.
The Assigned Virtual Output is using the default name. Change the
name.
An Input symbol is using a Contact Input, Contact Output, Digital
Element, FlexElement, or Digital Counter set to the default name.
Change the name so that it is unique.
An Input symbol is using a disabled Virtual Input, Contact Input, Digital
Element, FlexElement, Digital Counter, Control Pushbutton,
Programmable Pushbutton, Contact Output, or Protection/Monitoring
Element. Enable it and try again.
An Input symbol is set to OFF
An Input symbol is set to ON
The symbol block is using the default setting of OFF
The symbol block is using the default setting of OFF
4
4-41

Advertisement

Table of Contents

   Also See for GE C30

   Related Manuals for GE C30

Comments to this Manuals

Symbols: 0
Latest comments: