Download  Print this page

GE C30 Instruction Manual Page 140

Controller system.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416

Advertisement

FLEXLOGIC DESIGN AND MONITORING USING ENGINEER
The following information is contained in the compile window.
4
Number of Lines Saved — The number of compiled logic lines eliminated by using the optimization algorithm, as set in the
Optimize Compiled Output option of the Preferences. In the example shown, no lines were saved because the optimizer is
disabled.
FlexLogic Lines — The number of lines that the compiled logic uses, for example seven of 512 available.
Virtual Output equations — The number of FlexLogic equations used in the Logic Designer window.
Timers used — The number of timers used in the Logic Designer window.
Memory Used — The percent of memory used in the Logic Designer window.
Errors
Table 4-3: Errors from compiling
Category
Block or gate
affected
Error
All
Error
Tag-In
Error
1 Shots
Error
=VO
Error
Timer
4-40
Figure 4-42: Compiled results
Message
Number of lines (nnn) exceeds
maximum limit of 512
Tag-in not configured (TAG_ID,
SheetReference)
One Shot is over limit
(SYMBOL_ID, SheetReference)
VO has no inputs (VO_ID,
SheetReference)
Timer used more than once
(TIMER_ID, SheetReference)
Description
The compiled result exceeds the limit of 512. Reduce the number of
equations to 512 or less.
A Tag-In is connected to a circuit but the Tag-In is not referencing an
existing Tag-Out
The number of One-Shots contained within all of the VO blocks has
exceeded the maximum allowed for the firmware revision. This value can
either be 0 or 32.
A Virtual Output block is located within the FlexLogic diagram and there
is no block connected as input to it. Connect and identify the inputs.
The same timer is used in more than one place in the editor. This means
either the circuit that the Timer belongs to has been branched, or the
Timer has been duplicated.
C30 CONTROLLER SYSTEM – INSTRUCTION MANUAL
CHAPTER 4: INTERFACES

Advertisement

Table of Contents

   Also See for GE C30

   Related Manuals for GE C30

Comments to this Manuals

Symbols: 0
Latest comments: