Allgemeines Impressum Sicherheitshinweise Elektro-Automatik GmbH & Co. KG Helmholtzstrasse 31-33 • Das Gerät ist nur mit der angegebenen Netzspannung 41747 Viersen zu betreiben! Germany • Keine mechanischen Teile, insbesondere aus Metall, Telefon: 02162 / 37850 durch die Lüftungsschlitze in das Gerät einführen! Fax: 02162 / 16230 •...
Über das Gerät Einleitung Ansichten Die Labornetzgeräte der Serie PS 2000B sind sehr kom- Bedien- und Anschlußelemente pakte und robuste Geräte, die auf kleinem Raum eine Viel- zahl von interessanten Möglichkeiten bieten. Die Geräte Netzschalter eignen sich aufgrund des berührungsfreien Aufbaus und Dient zum Einschalten oder Ausschalten des Gerätes.
Page 5
Über das Gerät Bild 1 Bild 2a. Rückansicht 100W / 160W Bild 2b. Rückansicht 320W Bedienungsanleitung Stand: 18.04.2013 PS 2000 B Single Serie...
Über das Gerät Bedienung 4.2.2 Taste On/Off Diese Taste dient zum manuellen Ein- oder Ausschalten 4.1 Anzeige des Ausganges, sofern sich das Gerät nicht im Fernsteue- rungsbetrieb befindet. Der Zustand des Ausganges wird mit dem Statustext (ein) oder (aus) in der Anzeige angezeigt. Die Taste kann durch den Zustand LOCK blockiert sein.
Bedienung des Gerätes Welche Firmware-Version Ihr Gerät hat, können Sie nur Es läuft ein Countdown ab. Man hat nun folgende Mög- herausfinden, indem Sie die Gerätedaten über die USB- lichkeiten: Schnittstelle auslesen. Dazu können die Software EasyPS a) Man wartet, bis der Countdown abgelaufen ist. Danach 2000 von www.elektroautomatik.de herunterladen und ist das Bedienfeld gesperrt und LOCK aktiv.
Bedienung des Gerätes Weitere Anwendungen 5.4 Überstrom Bei Überstrom durch eine zu hohe Belastung kann das 7.1 Reihenschaltung Gerät auf zwei Arten reagieren: Mehrere Geräte gleichen Typs, aber zumindest gleichen 1. Abschaltung des Ausganges (OCP) oder Nennstromes, können in Reihe geschaltet werden, um die 2.
Bedienung des Gerätes 7.3 Fernsteuerung mit EasyPS2000 Das Gerät kann über die separat erhältliche Windows- Software EasyPS2000 und ein USB-Kabel (im Kit mit der Software bereits enthalten) ferngesteuert werden. Für weitere Informationen lesen Sie bitte im Handbuch zur Software EasyPS2000 bzw. auf der Hersteller-Webseite nach.
Über das Gerät 8.2 84V-Modelle PS 2084-03B PS 2084-05B PS 2084-10B Netzeingang Eingangsspannung 100…240V ±10% 100…240V ±10% 100…240V ±10% Frequenz 45…65Hz 45…65Hz 45…65Hz Sicherung T 2A T 3.15A T 6.3A Leistungsfaktor > 0.99 > 0.99 > 0.99 Leistungsaufnahme im Leerlauf Ausgang - Spannung Einstellbereich 0...84V...
Page 13
General About Safety instructions Elektro-Automatik GmbH & Co. KG Helmholtzstrasse 31-33 41747 Viersen • Only operate the device at a mains voltage as stipulated on the type plate! Germany • Never insert mechanical parts, especially from metal, Phone: +49 2162 / 37850 through the air ventilation slots! Fax: +49 2162 / 16230...
About the device Introduction Views The laboratory power supplies of the series PS 2000B are 3.1 Controls & sockets very compact and rugged devices and incorporate intere- sting features within small dimensions. The contactless design makes them ideally suited for operation in schools, Power switch educational facilities, workshops or laboratories.
Page 15
About the device Figure 1 Figure 2a. Rear view 100W / 160W models Figure 2b. Rear view 320W models Instruction manual Date: 18-04-2013 PS 2000 B Single Series...
Operating the device Handling 4.2 Pushbuttons 4.2.1 Pushbutton Preset 4.1 The display This button is used to switch to preset mode and for acti- vation/deactivation of the LOCK mode. Push Display Mode Display of U/I set values Display of OVP/OCP set values Activation/Deactivation of LOCK mode (also see 4.5)
Operating the device A countdown will be running. During this countdown you All set values are internally stored every 10 seconds have two options: and restored after powering the device next time. Thus it a) Wait until the countdown has finished. After this, the may happen, that the device does not restore the most control panel LOCK is active.
Operating the device Other applications 5.4 Overcurrent The device can react in two different ways to overload 7.1 Series connection resp. overcurrent: Several units of preferrably same type, but at least with 1. By switching the output off (OCP) or identical nominal current, can be connected in series in 2.
Operating the device 7.3 Remote control with EasyPS2000 The device can be remotely controlled via the USB port by means of a PC and a Windows software called Ea- syPS2000. The software and a USB cable are included in a seperately available kit.
About the device 8.2 84V models PS 2084-03B PS 2084-05B PS 2084-10B Mains input Input voltage 100…240V ±10% 100…240V ±10% 100…240V ±10% Frequency 45…65Hz 45…65Hz 45…65Hz Fuse T 2A T 3.15A T 6.3A Power factor > 0.99 > 0.99 > 0.99 Power consumption at output off Output - Voltage Adjustable range...
Page 24
EA-Elektro-Automatik GmbH & Co. KG Entwicklung - Produktion - Vertrieb Development - Production - Sales Helmholtzstraße 31-33 41747 Viersen Germany Telefon: 02162 / 37 85-0 Telefax: 02162 / 16 230 ea1974@elektroautomatik.de www.elektroautomatik.de...