Installation - Black & Decker DV4800 Original Instructions Manual

Table of Contents

Advertisement

Available languages

Available languages

  • ENGLISH, page 1
ENGLISH
Fig. A
8.
9.
10. Wet/Dry foam insert (WD4810, WD7210 and WD9610
Only)
11.
Fig. B
12. Squeegee (WD4810, WD7210 and WD9610 Only)
13. Powered brush head (DV9610P Only)

Installation

The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
suitable for the wall type and is appropriate to the weight of
the appliance.
Mark the location of the screw holes (within reach of an
u
electrical outlet for chargeing the vac while it is on the wall
bracket).
Insert the charger cord into the curved slot in the wall
u
mount bracket leaving approximately 8-9 inches excess.
Hang the appliance on the wall by placing the opening
u
on the base of the vac over the hooks in the wall mount
bracket.
Assembly
These models may be supplied with some of the following
accessories:
A squeege tool (12) for wet use on hard surfaces.
u
(WD4810, WD7210 and WD9610 Only)
A powered brush head (13) for vacuuming on cut pile
u
carpeting. The brush head is particularly useful for picking
up hair, threads, etc. (DV9610P Only)
Fitting (Fig. D)
Insert the appropriate accessory into the front of the appli-
u
ance. Make sure that the accessory is pushed fully in.
Use
u
24 hours.
Place the appliance on the charging base whenever it is
u
not in use. (WD4810, WD7210 and WD9610 Only)
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
6
(Original instructions)
Charging the battery (Fig. E & F)
Make sure that the appliance is switched off. The battery
u
will not be charged with the on/off switch in the on posi-
tion.
Plug the jack plug of the charger (6) into the charging
u
socket (4) of the appliance (Fig. E). (DV4800 and
Only)
DV9610P Only)
Place the appliance on the charging base (7) (Fig. F).
u
(WD4810, WD7210 and WD9610 Only)
Plug in the charger. Switch on at the mains. The charging
u
indicator (3) will be lit.
Leave the appliance to charge for at least 16 hours.
u
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
Dry pick up (DV4800, DV9610P)
For everyday spills of dry material.
u
Wet and dry pick up (WD4810, WD7210 and
WD9610 Only)
For everyday spills of dry material, use your appliance
u
without the squeegee accessory.
Warning! Your product is designed for light spills only.
This appliance can also be used to pick up everyday liquid
u
spills. Use the squeegee accessory on non-absorbent,
hard surfaces. On absorbent surfaces, such as carpet,
your appliance will pick up wet spills better without the
accessory.
For best performance on hard surface wet pickups, insert
u
squeegee into the bowl nozzle opening.
For best results when using this accessory, hold the appli-
u
ance at an angle of 45° and pull it slowly towards you.
u
there is any liquid in the bowl, do not turn the unit upside
down, sideways, point the nozzle upward, or shake the
vac excessively.
After picking up liquid substances clean the appliance and
u
not properly cleaned after wet pickups.
Before charging, be sure to empty all liquid contents and
u
dry thoroughly, to avoid damage to your appliance.

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dv9610pWd7210Wd9610Wd4810

Table of Contents